Grizzly Industrial G0462 - Manuals

-4- g0462 Wood Lathe (mfg. since 3/10) MACHINE DATA SHEET Customer Service #: (570) 546-9663 · To Order Call: (800) 523-4777 · Fax #: (800) 438-5901 MODEL G0462 WOOD LATHE WITH DIGITAL READOUT Product Dimensions: Weight....................................................................................

-6- g0462 Wood Lathe (mfg. since 3/10) For Your Own Safety, Read Instruction Manual Before Operating this Machine The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words intended to convey the level of importa...

-8- g0462 Wood Lathe (mfg. since 3/10) Additional Safety for Wood Lathes Like all machinery there is potential danger when operating this lathe. Accidents are frequently caused by lack of familiarity or failure to pay attention. Use this lathe with respect and caution to reduce the risk of operator ...

g0462 Wood Lathe (mfg. since 3/10) -9- 110v Operation SEcTION 2: cIRcUIT REQUIREMENTS Serious personal injury could occur if you connect the machine to power before com- pleting the setup process. DO NOT connect the machine to the power until instructed later in this manual. Electrocution or fire co...

-10- g0462 Wood Lathe (mfg. since 3/10) SEcTION 3: SETUp Wear safety glasses dur- ing the entire setup pro- cess! This machine presents serious injury hazards to untrained users. Read through this entire manu- al to become familiar with the controls and opera- tions before starting the machine! the ...

g0462 Wood Lathe (mfg. since 3/10) -11- Inventory the following is a list of the small components shipped with your machine. Lay the components out to inventory them. Note: If you can't find an item on this list, check the mounting location on the machine or examine the packaging materials carefully...

-12- g0462 Wood Lathe (mfg. since 3/10) The unpainted surfaces of your machine are coated with a heavy-duty rust preventative that prevents corrosion during shipment and storage. This rust preventative has been your machine's close ally and guardian since it left the factory. If your machine arrived...

g0462 Wood Lathe (mfg. since 3/10) -13- Site considerations figure 7. minimum working clearances. Wall Recommended 48" For Outboard Turning 75" 19" 30" Illustration Not To Scale Weight Load Refer to the Machine Data Sheet for the weight of your machine. Make sure that the surface upo...

-14- g0462 Wood Lathe (mfg. since 3/10) Although not required, we recommend that you mount your new machine to the floor. Because this is an optional step and floor materials may vary, floor mounting hardware is not included. generally, you can either bolt your machine to the floor or mount it on ma...

g0462 Wood Lathe (mfg. since 3/10) -15- To mount the lathe to the stand: 1. stand the legs up approximately 41" apart, then get them reasonably aligned, as shown in figure 10. Assembly figure 10. stand legs approximately 41" apart to prepare for mounting the lathe. 4. install the tool rest l...

-16- g0462 Wood Lathe (mfg. since 3/10) Test Run once the assembly is complete, test run your machine to make sure it runs properly. if, during the test run, you cannot easily locate the source of an unusual noise or vibration, stop using the machine immediately, then review the Troubleshooting on p...

-18- g0462 Wood Lathe (mfg. since 3/10) Loose hair and cloth- ing could get caught in machinery and cause seri- ous personal injury. Keep loose clothing and long hair away from moving machinery. SEcTION 4: OpERATIONS the model g0462 headstock can be positioned anywhere along the bed and pivoted up t...

g0462 Wood Lathe (mfg. since 3/10) -19- To pivot the headstock: 1. disConneCt LAthe From poWer! 2. make sure the head lock lever is tight. 3. pull the pivot lock pin out (see figure 18) and pivot the headstock clockwise 90˚ or 180˚, as shown in figure 19. the tailstock is equipped with a cam-action ...

g0462 Wood Lathe (mfg. since 3/10) -21- figure 23. inserting spur center into spindle. spur Center 5. insert the tapered end of the center into the spindle, then push it in with a quick, firm motion (see figure 23). 6. make sure the center is securely installed by attempting to pull it out by hand—a...

-24- g0462 Wood Lathe (mfg. since 3/10) spindle turning, as shown in figure 31, is the operation performed when a workpiece is mount-ed between the spindle and quill centers. Workpiece Workpiece Center Pencil Lines Marked Diagonally Across Corners figure 32. Workpiece marked diagonally from corner t...

g0462 Wood Lathe (mfg. since 3/10) -25- 1/4" figure 33. spur center properly embedded. 7. With the workpiece still attached, insert the spur center into the spindle. 8. With the live center installed in the quill, draw the quill back into the spindle as far as pos-sible without forcing the cente...

-26- g0462 Wood Lathe (mfg. since 3/10) figure 37. Attaching the faceplate to a backing block, which is glued to the workpiece. figure 35. typical faceplate turning operation. Faceplate turning, as shown in figure 35, is when a workpiece is mounted to the faceplate that is then mounted to the spindl...

g0462 Wood Lathe (mfg. since 3/10) -27- outboard turning is a variation of faceplate turn-ing and is usually done when stock diameter is greater than 12''. For the size of the model g0462 and its minimum turning speed, we recommend a maximum diameter of 17'' for outboard turning. the lathe setup at ...

-28- g0462 Wood Lathe (mfg. since 3/10) G1194—3-Jaw chuckA "must have" for the serious wood turner. this 3-jaw chuck is a self-centering style chuck used mostly for round work. All three jaws tighten together at the same time. Jaws are reversible for expanded work holding capacity. Threaded ...

-30- g0462 Wood Lathe (mfg. since 3/10) SEcTION 6: MAINTENANcE For optimum performance from your machine, follow this maintenance schedule and refer to any specific instructions given in this section. Daily check:• Loose mounting bolts. • Worn switch. • Worn or damaged wires. • damaged V-belt. • Any...

g0462 Wood Lathe (mfg. since 3/10) -31- review the troubleshooting and procedures in this section to fix or adjust your machine if a problem devel-ops. if you need replacement parts or you are unsure of your repair skills, then feel free to call our technical support at (570) 546-9663. SEcTION 7: SE...

g0462 Wood Lathe (mfg. since 3/10) -33- figure 49. Center tips touching to ensure alignment. Aligning centers to ensure accurate and safe results, make sure that the spindle and quill centers are aligned before beginning operations. To align the centers: 1. disConneCt LAthe From poWer! 2. remove the...

-34- g0462 Wood Lathe (mfg. since 3/10) READ ELECTRICAL SAFETY ON PAGE 34! these pages are current at the time of printing. however, in the spirit of improvement, we may make chang-es to the electrical systems of future machines. study this section carefully. if there are differences between your ma...

g0462 Wood Lathe (mfg. since 3/10) -35- READ ELECTRICAL SAFETY ON PAGE 34! Electrical components & Wiring Diagram Neutral Hot Ground 110 VAC NEMA 5-15 Plug (As Recommended) Paddle Switch Digital Readout Spindle Speed Sensor Motor Bk Bk Bk Bk Bk Wt Wt Wt Wt Gr Gr Gr Rd Capacitor 100MFD 250VAC fig...

g0462 Wood Lathe (mfg. since 3/10) -37- parts List REF PART # DESCRIPTION REF PART # DESCRIPTION 1 PS05M PHLP HD SCR M5-.8 X 8 40 PR58M EXT RETAINING RING 24MM 2 P0462002 MOTOR COVER 41 P0462041 SPEED CHANGE LABEL 3 PB26M HEX BOLT M8-1.25 X 30 42 P0584048 SPEED CONTROL LEVER ASSY 4 PLW04M LOCK WASHE...

-38- g0462 Wood Lathe (mfg. since 3/10) 89 90 91 93 93 94 95 Machine Labels Safety labels warn about machine hazards and ways to prevent injury. The owner of this machine MUST maintain the original location and readability of the labels on the machine. If any label is removed or becomes unreadable, ...

C U T A LO N G D O T T E D LI N E Name _____________________________________________________________________________ Street _____________________________________________________________________________City _______________________ State _________________________ Zip _____________________Phone # _____...

WARRANTy AND RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of main...

Buy Direct and Save with Grizzly ® – Trusted, Proven and a Great Value! ~Since 1983~ ORDER 24 HOURS A DAY! 1-800-523-4777 Visit Our Website Today For Current Specials!