Graham Field 765000 - Manuals

Graham Field 765000 – Manual in PDF format online.

Manuals:

Manual

Manual Graham Field 765000

Summary

Page 2 - CONTENTS

2 765000-INS-LAB-RevB10 CONTENTS INTRODUCTION ..................................................................................... 3 INTENDED USE OF THIS DEVICE ........................................................ 3 IMPORTANT SAFETY PRECAUTIONS .....................................................

Page 3 - INTRODUCTION; INTENDED USE OF THIS DEVICE; • Aid in the treatment and prevention of stage 1, 2, 3 and

765000-INS-LAB-RevB10 3 INTRODUCTION Use this manual for set-up and operation of the Lumex ® AltaDyne ® Sensor Plus 765000 Alternating Pressure Mattress System with Active Sensor Technology. Read all instructions before using the mattress system. Save this manual for future reference. INTENDED USE O...

Page 4 - IMPORTANT SAFETY PRECAUTIONS; Caution: Indicates a potential hazard or unsafe prac-; immediately; WARNING

4 765000-INS-LAB-RevB10 IMPORTANT SAFETY PRECAUTIONS The safety statements presented in this chapter refer to the basic safety information that should be observed by those using this Mattress System. There are additional safety statements in other chapters or sections, which may be the same as or si...

Page 5 - only; WARNING: Maximum patient weight capacity for this

765000-INS-LAB-RevB10 5 WARNING: Always use close supervision when this product is used by, on, or near children or those who require close supervision. WARNING: Use this product only as intended and described in this manual. Do not use attachments or accessories not recommended by Graham-Field. WAR...

Page 6 - equipment specified by the bed manufacturer may not; CAUTION

6 765000-INS-LAB-RevB10 WARNING: Patient entrapment with bed side rails may cause injury or death. The bed frame and its components, including the mattress, bed side rails, head and foot board, bedding, and any accessories added to the bed, can all affect the risk of entrapment. Thorough patient ass...

Page 7 - EQUIPMENT SYMBOLS; please consult your local city office, household waste disposal

765000-INS-LAB-RevB10 7 EQUIPMENT SYMBOLS Manufacturer Indicates that this product is according to the degree of protection against electric shock for type BF equipment Functional earth (for UL only) Attention! Read the instructions! Disposal of Electrical & Electronic Equipment (WEEE): Do not t...

Page 8 - PRODUCT DESCRIPTION; PUMP AND MATTRESS SYSTEM; pump and mattress system

8 765000-INS-LAB-RevB10 PRODUCT DESCRIPTION PUMP AND MATTRESS SYSTEM pump and mattress system CPR valves quick connectors (mattress-pump connectors) mattress foot end symbol pump PUMP: FRONT quick connector front panel PUMP: REAR main power switch power cord receptacle fuse hanger filter

Page 9 - Front panel, first row; The auto-adjust button

765000-INS-LAB-RevB10 9 PUMP: FRONT PANEL Front panel of pump is shown below. Descriptions of but-tons and indicators follow. Tuning button; indicators at left of button Power failure indicator Alarm mute button Service indicator Power (ON/OFF) button; indicator at right of button Panel lock button;...

Page 11 - Front panel, third row; The panel lock button sets the

765000-INS-LAB-RevB10 11 Maxfirm button: The pump will automatically enter maxfirm mode every time the power is turned on. Maxfirm mode ensures the pump is able to reach its maximum oper- ating pressure. Maxfirm mode will last for 20 minutes, and then the system will automatically enter auto-adjust ...

Page 12 - Low pressure indicator:; Check to ensure all connections are properly and se; Power failure indicator:; indicator illuminates, and the alarm sounds, when there is

12 765000-INS-LAB-RevB10 Low pressure indicator: The low pressure indicator (yellow LED) illuminates, and the alarm sounds, when an abnormally low pressure level occurs. If the low pressure indicator persistently illuminates inappropriately: 1. Check to ensure all connections are properly and se - c...

Page 13 - INSTALLATION; UNPACKING; carrier and your Graham-Field equipment provider.; PUMP AND MATTRESS SETUP; bed frame ensure that the foot; Caution: Place the device in a; into place before continuing.; Caution: Ensure that the air hoses are not kinked or

765000-INS-LAB-RevB10 13 INSTALLATION UNPACKING 1. Carefully remove all components from the carton.2. Inspect all components.3. If damage is evident to the contents, please notify the carrier and your Graham-Field equipment provider. PUMP AND MATTRESS SETUP 1. Remove all sheets, blankets, and pillow...

Page 15 - OPERATION; GETTING STARTED; ters alternate therapy mode.; QUICK DISCONNECT; Pull the power plug from the wall connector to disconnect

765000-INS-LAB-RevB10 15 OPERATION GETTING STARTED 1. Turn the main power switch to the ON position. 2. Press the front panel power button. The power indicator will illuminate. Note: The mattress system will automatically enter maxfirm mode for the quickest inflation at set-up; when inflated, it wil...

Page 16 - TRANSPORT CAP; In case of power failure or trans; CPR FUNCTION; If CPR must be performed on the patient while the mat

16 765000-INS-LAB-RevB10 TRANSPORT CAP In case of power failure or trans - port: Disconnect the quick connec - tor and cap the mattress with the transport cap to slow deflation. Note: This system is equipped with cell-on-cell technology to provide added support and prevent bottoming out in the event...

Page 17 - MAINTENANCE; CLEANING; WARNING: To reduce the risk of increased bacterial; Pump; : Wipe the pump with a clean, damp cloth and mild; Caution: Do not use phenolic products or corrosive or; : Wipe the mattress unit with a clean, damp cloth; Caution: Do not clean the mattress with phenolic; sure mattress cover and tubes are connected correctly.

765000-INS-LAB-RevB10 17 MAINTENANCE CLEANING WARNING: To reduce the risk of increased bacterial growth, infection, illness, or injury from contamination, thoroughly clean and dry the mattress system before use and as necessary during use as follows: Pump : Wipe the pump with a clean, damp cloth and...

Page 18 - Fuse replacement; Replace the fuse holder cover. Ensure that fuse holder; Air filter replacement; Use a small screwdriver to remove; STORAGE; Store mattress and pump in a dust-free environment

18 765000-INS-LAB-RevB10 Fuse replacement tool needed: small screwdriver 1. If you suspect a blown fuse, discon - nect the plug from the wall outlet immediately. 2. Use a small screwdriver to remove the cover of the fuse holder (fuse lo-cations are shown in picture at right). 3. Insert a new fuse of...

Page 19 - SPECIFICATIONS; Classification; Mattress; Note: Specifications are subject to change without notice.

765000-INS-LAB-RevB10 19 SPECIFICATIONS Pump Specification Power Supply (Note: see rating label on product) AC 120V 60 Hz 0.17A (for 120V system) Fuse Rating T1A, 250V Cycle time Fixed / 10 minutes Dimensions (L x W x H) 11.4" x 7.9" x 4.6" (29.1 x 20 x 11.7 cm) Weight 5 lb (2.2 kg) Envi...

Page 20 - LIMITED WARRANTY; GF Health Products, Inc. warrants the Lumex

20 765000-INS-LAB-RevB10 LIMITED WARRANTY GF Health Products, Inc. warrants the Lumex ® AltaDyne ® Sensor Plus 765000 Alternating Pressure Mattress Sys-tem with Active Sensor Technology for a period of twelve months for defects in workmanship and materials. If a product is deemed to be under warrant...

Page 21 - APPENDIX A: EMC INFORMATION

765000-INS-LAB-RevB10 21 APPENDIX A: EMC INFORMATION Guidance and Manufacturer’s Declaration- Electromagnetic Emissions: This device is intended for use in the electromagnetic environment specified below. The user of this device should make sure it is used in such an environment. Emissions Test Comp...