Graco 309273 - Manuals - manualsarea.com

Page 2 - PRESSURE RELIEF; – Do this when cleaning, repairing or shuting down sprayer; Turn power; OFF; Put drain tube in pail; WARNING

2 309273 PRESSURE RELIEF – Do this when cleaning, repairing or shuting down sprayer WASTE RESÍDUOS À JETER DESECHO 1. Turn pressure to lowest setting. Turn power OFF . Unplug sprayer. 2. Trigger gun to relieve pressure. 3. Put drain tube in pail . Turn prime valve down. WARNING Fire and explosion ha...

Page 3 - Component Identification; Paint position

3 309273 Power Switch Pressure Control Component Identification Suction Tube Filter Prime Valve Prime/drain position Paint position Spray Gun Trigger Safety Put trigger safety ON when not spraying. Take trigger safety OFF before triggering gun. Digital Display (Not available on all models) 15/20A Sw...

Page 4 - Connect Graco airless hose to sprayer.; Setup

4 309273 1. Connect Graco airless hose to sprayer. Tighten securely. 2. Connect other end of hose to gun. Setup 3. Tighten securely. 4. Remove tip guard.

Page 6 - Plug power supply cord into a properly grounded; Startup; to flush out storage oil shipped in

6 309273 PAINT FLUSH 7. Turn power OFF . 8. Plug power supply cord into a properly grounded electrical outlet. 9. Turn prime valve down. 10. Place suction tube and drain tube in grounded metal pail partially filled with flushing fluid. Attachground wire to pail and to true earth ground. Do 1 . – 5 ....

Page 7 - Do not stop leaks with your hand or a rag!; ON

7 309273 FLUSH Note: Inspect fittings for leaks. Do not stop leaks with your hand or a rag! If leaks occur, do Pressure Relief . Tighten leaky fittings. Repeat Startup, 1. – 5 . If no leaks, continue to trigger gun until system is thoroughly flushed. Proceed to 6. Startup 15 SEC 1. Turn prime valve ...

Page 8 - General Surfaces Tip Recommendations Chart; Trigger gun again into flushing fluid pail until

8 309273 FLUSH PAINT General Surfaces Tip Recommendations Chart Wood Interior Cab-inets, Paneling Interior Walls or CeilingsDrywall, Plaster Over Hang Surfaces Materials FilterMesh 6–8 8–10 10–12 12–14 OrificeSize (in.) Fan Width (in.) at 12 in. Masonry Block, Stucco, Concrete Wood ExteriorShingle, ...

Page 10 - Put trigger safety ON, return SwitchTip

10 309273 Spray Test Pattern heavyedges Clearing Tip Clogs 1. Trigger gun and spray test pattern. Slowly adjust pressure to eliminateheavy edges. Use smaller tip size ifpressure adjustment can not eliminateheavy edges. 2. Hold gun perpendicular, 10–12 in. (25–30 cm) from surface. Spray backand forth...

Page 11 - Cleanup; PAINT

11 309273 Cleanup PAINT 1. Turn power OFF . 2. Turn pressure to lowest setting. Trigger gun to relieve pressure. 3. Turn prime valve down. 4. Remove filter assembly and assemble gun without filter. Perform AutoClean procedure (Manual 309278) or follow conventional flushing/cleaning procedure that fo...

Page 12 - Remove siphon tube set from paint and place

12 309273 5. Remove guard and SwitchTip. 6. Clean filter, guard and SwitchTip in flushing fluid. PAINT FLUSH 7. Remove siphon tube set from paint and place in flushing fluid. Use water for water basepaint and mineral spirits for oil base paint. 8. If sprayer has a filter, unscrew bowl, remove filter...

Page 13 - Take trigger safety; Turn prime valve down and allow

13 309273 PAINT FLUSH 9. Turn power ON. 10. Turn prime valve hori- zontal. 11. Hold gun against paint pail. Take trigger safety OFF . Trigger gun until flushingfluid appears. 12. Move gun to flushing pail, hold gun against pail, trigger gun tothoroughly flush system. Release trigger and put triggers...

Page 15 - Trouble Shooting

15 309273 Trouble Shooting TYPE OF PROBLEM WHAT TO CHECK If check is OK, go to next check WHAT TO DO When check is not OK refer to this column D Sprayer does not respond 1. Check if error code is displayed, page 9. 1. Refer to your repair manual. D Sprayer will not primeor takes too long toprime 1 ....

Page 16 - Wrap power cord and; Graco Phone Number

16 309273 Daily: Inspect, clean and replace as needed D Manifold filter, gun filter and inlet stainer D Wet cup for leakage, tighten if needed D TSL level D Gun trigger safety D Tip wear, replace if necessary D Electric cord and plug Weekly: D Check tightness of wet cup. D Inspect all high pressure ...