Graco 12 VDC - Manuals - manualsarea.com

Page 2 - Models

Models 2 311304H Models Part No. Hose Nozzle 12 VDC, 10 gpm (38 lpm), 12.5 amps 260000 260069 - 12 ft (3.66 m) grounded 260079 - manual, leaded/diesel 260001 260069 - 12 ft (3.66 m) grounded 260082 - automatic, regular/diesel 260002 260069 - 12 ft (3.66 m) grounded 260078 - manual, unleaded 260003 2...

Page 4 - Warnings; WARNING

Warnings 4 311304H Warnings The following general warnings are for the setup, use, grounding, maintenance, and repair of this equipment. Addi-tional, more specific warnings may be found throughout the body of this manual where applicable. Symbols appear- ing in the body of the manual refer to these ...

Page 6 - Installation; Mounting Pump

Installation 6 311304H Installation When unpacking pump, check for shipping damage. Report any shipping damage to delivering carrier imme-diately. Mounting Pump 1. Apply PTFE thread tape (provided with the pump) to large thread of bung adapter (9) (2 in. X 1 ½ in. reducer fitting). Install bung adap...

Page 7 - Mounting Hose and Nozzle

Installation 311304H 7 3. Cut the suction tube so that it is 2 in. (55 mm) from the bottom of the tank when installed in the tank. 4. Insert gasket (7f) into union nut (1k). If using Graco supplied PVC suction tube it is not necessary to apply thread tape before assembly, just screw into pump inlet ...

Page 9 - Priming Pump; If prime is lost; Operation

Operation 311304H 9 Priming Pump All pump models should prime within 5 seconds after pump is turned on up to a height of 36 in. (91 mm). Pumps installed at height up to 5 ft. (1.52 m) may have difficulty priming. Follow procedure below to initiate prime. Pumps installed at suction height above 5 ft....

Page 10 - Troubleshooting

Troubleshooting 10 311304H Troubleshooting Problem Cause Solution Motor runs but pump will not prime. Motor rotation wrong. (12 VDC and 24 VDC units only.) Check wiring instructions for possible problems. Missing relief valve o-ring seal (4c/7a). Remove gear cover (1b) inspect seal (4c/7a), replace ...

Page 12 - Parts Drawing

Parts Drawing 12 311304H Parts Drawing 3a 3c 3d/7e 1a 8e 8b 8f 8g 1h 1e/7b/10c 1f/7c/10b 2e 2f 3b 1b 1c/ 10a 1d 4b 4a 2h 2i 8c 8a 8d 4c/ 9 7f 1k 1g/7d 2g 2c 2b 2d 5c 5a 2a 2c 6b 6c 6a Models 260000 through 260017, 260019, 260024, 260580, and 260581, 12 VDC Models 260020 and 260021, 24 VDCModels 2600...

Page 13 - Parts List

Parts List 311304H 13 Parts List Models 260000 through 260017, 260019, 260024, 260580, and 260581, 12 VDCModels 260020 and 260021, 24 VDCModels 260022 and 260023, 230 VACModels 260025 through 260028, 115 VAC Ref. No. Description Qty . 1 260458 KIT, pump with swivel, blue(includes items 1a-1k) 260459...

Page 15 - Technical Data; Performance Chart

Technical Data 311304H 15 Technical Data Valox ® is a registered trademark of the General Electric Company Performance Chart Working pressure 10 psi (0.07 MPa, 0.7 bar) Inlet size 1 in. npt Outlet size 3/4 in. npt Weight 20 lb (9 kg) Power cable 18 ft (5.5 m), 14 AWG (12 VDC and 24 VDC models only) ...

Page 16 - Graco Standard Warranty; Graco Information

All written and visual data contained in this document reflects the latest product information available at the time of publication. Graco reserves the right to make changes at any time without notice. This manual contains English. MM 311304 Graco Headquarters: Minneapolis International Offices: Bel...