GMC LS8B - Manuals - manualsarea.com

Page 2 - Contents; Full 2 Years Home Use Warranty

Contents Warranty 2 Introduction 3 Description of symbols 3 Specifications 3 Safety rules for laser lights 3 Safety instructions 4 Additional safety rules for band saws 5 Unpacking 6 Accessories 6 Know your product 7 Assembly 8 Upper blade guide adjustment 8 Lower blade guide adjustment 9 Housing do...

Page 3 - Do not stare directly at the laser beam. A; Dear Customer; Carefully read through this entire Instruction; Environmental protection

Description of symbols The rating plate on your tool may show symbols. Theserepresent important information about the product orinstructions on its use. Wear hearing protection. Wear eye protection. Wear breathing protection. Conforms to relevant standards forelectromagnetic compatibility. Specifica...

Page 4 - Safety instructions; Consider the environment in which you are working.

• Never aim the beam at any person or an object otherthan the work piece. • The laser beam shall not be deliberately aimed atpersonnel and shall be prevented from being directedtowards the eye of a person for longer than 0.25s. • Always ensure the laser beam is aimed at a sturdy workpiece without re...

Page 5 - Have your tool repaired by a qualified person.; Additional safety rules for band saws

8. Use safety accessories. Safety glasses and earmuffs should always be worn. A face or dust mask is alsorequired if the operation creates dust. 9. Do not abuse the power cord. Never pull the cord to disconnect the charger from the power point. Keep thecord away from heat, oil and sharp edges. 10. D...

Page 6 - Unpacking; Work table

• Support the work properly. • Never reach over the blade to remove waste or off cuts. • Do not attempt to free a jammed blade before firstswitching off the machine. • Do not slow or stop a blade with a piece of wood. Letthe blade come to rest naturally. • If you are interrupted when operating the s...

Page 7 - Know your product

Know your product 1. Saw blade2. Upper housing locking screw3. Lower housing locking screw4. Upper housing door5. Lower housing door6. Laser assembly7. Laser on/off switch8. Blade tension knob9. On/Off switch10. Work table trunnion11. Work table12. Table insert13. Rip fence14. Rip fence locking hand...

Page 9 - Lower blade guide adjustment; Lower Blade Guide Adjustments

9 3. To adjust the height of the upper blade guide loosenthe blade guide lockingknob (17) and then adjustthe height using the bladeguide setting knob (16). 4. Tighten the blade guide locking knob (17) tosecure the upper bladeguide in place. 5. The upper blade guide consists of a thrust bearingthat s...

Page 10 - Housing doors

10 4. The work table needs to be tilted 45° or removedbefore the thrust bearinglocking screw and guidepins can be adjusted. Thrust bearing adjustment 5. To adjust the thrust bearing loosen the thrustbearing locking screw using the Allen key supplied. It iseasier to access the thrust bearing screw if...

Page 13 - Operation

13 1. Remove the rip fence (13) from the table. 2. Remove the U shape from under the work table byremoving the two screwsand two thumb nuts. 3. Open both housing doors.4. Swing the lower blade guide out of the way. 5. Loosen the blade tension knob to slacken the blade. 6. Remove the blade by guiding...

Page 14 - DO NOT

14 Using the REDEYE laser line generator WARNINGS. Do not stare directly at the laser beam. Never aim the beam at any person or an object other than thework piece.Do not deliberately aim the beam at personnel and ensurethat it is not directed towards the eye of a person.Always ensure the laser beam ...

Page 16 - GMC Product Type; Save this Manual for future reference.

Carefully read the entire Instruction Manual before using this product. Before returning this product for a Warranty Claim or any other reason Please Call 1300 880 001 (Australia)or 0800 445 721 (New Zealand) When you make your call, please have the following information at hand: • GMC Product Type ...