GMC LDP13B12 - Manuals - manualsarea.com

Page 2 - Contents; Full 2 Years Home Use Warranty

2 Contents Full 2 Years Home Use Warranty Whilst every effort is made to ensure your complete satisfaction with this tool, occasionally, due to the mass manufacturing techniques, a tool may not live up to our required level of performance and you may need the assistance of our service department.Thi...

Page 4 - Safety rules for laser lights; General safety instructions; Consider the environment in which you are working.

4 Safety rules for laser lights The laser light/laser radiation used in the GMC REDEYE® system is Class 1 with maximum 1mW power and 650nm wavelengths. These lasers do not normally present an optical hazard, although staring at the beam may cause flash blindness. Warning. Do not stare directly at th...

Page 6 - Additional safety rules for drill presses

6 Additional safety rules for drill presses Warning. For your own safety, do not try to use your drill press or plug it in until it is completely assembled and installed according to the instructions and until you have read and understood the following:1. Your drill press must be bolted securely to ...

Page 8 - Accessories

8 Accessories The LDP13B is supplied with the following components:1. Base2. Column3. Rack 4. Rack Collar5. Table6. Belts (x2)7. Handle8. Keyless Chuck9. Extension Table Locking Knobs (x4)10. Motor Head11 . Handle12. Depth Scale13. Table Lock14. Worm15. Hex Keys (x3) 16. Bolts for attaching column t...

Page 9 - Know your product

9 Know your product 1. Laser light on/off switch2. Laser aperture (x2)3. On/off switch4. Pulley cover5. Base6. Column7. Rack 8. Rack Collar9. Table/Support Assembly10. Belts (x2)11. Belt Tension Lever12. Table Handle13. Keyless Chuck14. Extension Table Locking Knobs (x4) 15. Motor Head16. Feed Handl...

Page 10 - Assembly

10 Assembly 1. Place base on floor.2. Place column assembly on base and align the 4 holes in the column assembly with the holes in the base. 3. Using the 4 8mm diameter x 20mm long bolts secure the column support to the base and tighten with a wrench. 4. Loosen the screw on the rack collar using the...

Page 11 - Adjustments; Adjusting the table height

11 16. Fit the table lock into the table support assembly and tighten to secure the table. 17. Fit the depth scale/lock onto the handle. 18. Fit the handle and depth scale onto the motor head ensuring that the flats on the handle locate the flats on the shaft. 19. Secure the handle onto the motor he...

Page 12 - Installing and removing drill bits

12 1. Loosen the screw under the table by rotating it in an anti-clockwise direction. 2. Tilt the table to the desired angle as indicated on the bevel scale. 3. Tighten the screw under the table by rotating it in a clockwise direction. Note. When the table is tilted the work piece should be clamped ...

Page 13 - Changing the speed; Tool Storage; REDEYE; REDEYE; Table and Head

13 3. Holding the handle in that position rotate the depth scale to the desired drilling depth. 4. Tighten the handle screw firmly to secure the handle in position. 5. Lift the handle up and then proceed with the drilling operation. 6. To disable the depth lock loosen the handle screw and rotate the...

Page 16 - Turn the on/off switch to the off position and; Troubleshooting; Problem

16 Troubleshooting Warning. Turn the on/off switch to the off position and unplug the tool from the power supply before performing trouble shooting procedures. Troubleshooting Problem Cause Solution Drill press will not start Power cord not plugged in Ensure that the cord is connected to the power s...

Page 17 - GMC Product Type; The GMC 777 Helpline operates from 7am to; Save this Manual for future reference.

17 Carefully read the entire Instruction Manual before using this product. Before returning this product for a Warranty Claim or any other reason Please Call 1300 880 001 (Australia)or 0800 445 721 (New Zealand) When you make your call, please have the following information at hand: • GMC Product Ty...