GMC 1050W - Manuals - manualsarea.com

Page 2 - Contents

Page 3 - Yes; Dear Customer; Carefully read through this entire Instruction; Environmental protection

Description of symbols The rating plate on your tool may show symbols. Theserepresent important information about the product orinstructions on its use. Wear hearing protection. Wear eye protection. Wear breathing protection. Double insulated for additional protection. Conforms to relevant standards...

Page 4 - General safety instructions; Consider the environment in which you are working.

General safety instructions The tool must be used only for its prescribed purpose. Anyuse other than those mentioned in this Manual will beconsidered a case of misuse. The user and not themanufacturer shall be liable for any damage or injuryresulting from such cases of misuse.To use this tool proper...

Page 5 - Have your tool repaired by a qualified person.

15. Avoid unintentional starting. Always check that the switch is in the OFF position before plugging in thetool to the power supply. Do not carry a plugged intool with your finger on the switch. 16. Stay alert. Watch what you are doing. Use common sense. Do not operate a power tool when you aretire...

Page 6 - x Feather boards

• Before using the tool to make a cut, switch on and letit run for a while. Watch for vibration or wobbling thatcould indicate an improperly installed bit. • Take notice of the direction of rotation of the bit andthe direction of feed. • Always switch off and wait until the bit has come to acomplete...

Page 7 - Know your product; knobs

Know your product 1. Table2. Rear fence3. Infeed fence4. Outfeed fence5. Fence locking knobs6. Guide block locking knobs 7. Dust extraction hood8. Dust extraction port9. On/Off switch10. Mitre gauge11. Mitre gauge locking knob12. Spindle lock lever13. Variable speed dial14. Height adjustment lock 7 ...

Page 8 - Installing and removing collets; Always ensure the tool is switched off and the

Installing and removing collets Warning. Always ensure the tool is switched off and the plug is removed from the power point before making anyadjustments.When changing the collets or when changing bits, theheight of the motor assembly should be raised to close tothe maximum height to gain full acces...

Page 9 - Installing and removing router bits

11. Replace the collet assembly cover in the following way: 11. The collet assembly coverlocates in the centre ofthe height adjusting ringand is secured in placewith two small screws. 11. The cover is usually fittedafter the cutter has beeninstalled, thus you needto select the cover whichwill pass o...

Page 10 - Adjustments; Adjusting the speed

Adjustments Adjusting the speed 1. Adjust the variable speed dial (9) to suit differentmaterial. The tool cutsquicker and smoother atdifferent speeds and whenworking in different woodsor in plastic or aluminium. 2. Adjust the variable speed dial to a higher number forfaster speed or to a lower numbe...

Page 11 - Adjusting the fence for trimming; Installing and adjusting the feather boards

Adjusting the fence for trimming 1. When trimming timber the material coming out on the left hand side (outfeed) (4) of the cutter will bethinner than the material being fed through on theright hand side (infeed) (3). 2. The left hand guide block will need to be adjusted to compensate for the thinne...

Page 13 - Power cord maintenance

Operation 1. Insert and secure the router bit.2. Adjust the speed, depth of cut, feather boards, fence alignment and mitre gauge as required. 3. Ensure you adjust the infeed fence (3) so that it supports the uncut material and the outfeed fence (4)so that it supports the cut material, compensating f...

Page 14 - GMC Product Type; Save this Manual for future reference.

Carefully read the entire Instruction Manual before using this product. Before returning this product for a Warranty Claim or any other reason Please Call 1300 880 001 (Australia)or 0800 445 721 (New Zealand) When you make your call, please have the following information at hand: • GMC Product Type ...