Giant 1-Feb - Manuals - manualsarea.com

Page 2 - FastHub 400 10/100 Series Installation and Configuration Guide; Warnings; the maximum recommended ambient temperature of 113

Warnings FastHub 400 10/100 Series Installation and Configuration Guide 2-2 Warnings Translated versions of the following safety warnings are provided in Appendix E,“Translated Safety Warnings.” Warning Only trained and qualified personnel should be allowed to install or replace this equipment. Warn...

Page 3 - Installing and Starting Up the Hub 2-3; earth ground during normal use.; EMC Regulatory Statements; Taiwan

Installing and Starting Up the Hub 2-3 EMC Regulatory Statements Warning This equipment is intended to be grounded. Ensure that the host is connected to earth ground during normal use. Warning When installing the unit, the ground connection must always be made first and disconnected last. Warning Do...

Page 4 - Installation Guidelines and Requirements; Clearance to front and rear panels is such that:; — Front-panel indicators can be easily read.; switched uplink module.; — Rear-panel power connectors are within reach of power sources.; Airflow around the hub and through the vents is unrestricted.; Unpacking the Hub; Follow these steps to unpack the hub:

Installation Guidelines and Requirements FastHub 400 10/100 Series Installation and Configuration Guide 2-4 Installation Guidelines and Requirements When determining where to place the hub, ensure the following conditions are met: • Cable distances from the hub to network equipment and workstations ...

Page 5 - Package Contents; — Four rubber feet for installing the hub on a table or shelf; Note

Installing and Starting Up the Hub 2-5 Package Contents Package Contents Each hub is shipped with the following items: • FastHub 400 10/100 Series Cabling and Start Up • This FastHub 400 10/100 Series Installation and Configuration Guide • Cisco Documentation CD-ROM • AC power cord • Mounting kit co...

Page 6 - Powering Up the Hub and Running POST

Powering Up the Hub and Running POST FastHub 400 10/100 Series Installation and Configuration Guide 2-6 Powering Up the Hub and Running POST Before installing and cabling the hub, you might want power up the hub and verify that itis operational. To power up the hub, connect one end of the AC power c...

Page 7 - Installing the Hub on a Table or Shelf; To install the hub on a table or shelf, follow these steps:

Installing and Starting Up the Hub 2-7 Installing the Hub on a Table or Shelf Installing the Hub on a Table or Shelf To install the hub on a table or shelf, follow these steps: Step 1 Be sure the hub is powered off and is not connected to a power source. Step 2 Locate the adhesive strip with the rub...

Page 8 - Installing the Hub in a Rack; perform the steps in the sections that follow.; Attaching the Brackets to the Hub

Installing the Hub in a Rack FastHub 400 10/100 Series Installation and Configuration Guide 2-8 Installing the Hub in a Rack This section describes how to install the hub in 19- and 24-inch standard and telco racks. Note Be sure the hub is powered off and is not connected to a power source before yo...

Page 10 - Attaching the Hub to the Rack; Attaching the Hub to a Rack (Front Panel Forward)

Installing the Hub in a Rack FastHub 400 10/100 Series Installation and Configuration Guide 2-10 Attaching the Hub to the Rack After the brackets are attached, use two of the Phillips machine screws to securely attacheach bracket to the rack, as shown in Figure 2-4. Figure 2-4 Attaching the Hub to a...

Page 11 - Attaching the Cable Guide to the Bracket; Attaching a Cable Guide

Installing and Starting Up the Hub 2-11 Attaching the Cable Guide to the Bracket Attaching the Cable Guide to the Bracket Attaching the cable guide and securing the cables in the cable guide prevent the cables fromobscuring the hub and other devices in the rack. If the hub is in a 19- or 24-inch rac...

Page 12 - Installing the Hub on a Wall; Attaching Brackets for Parallel and Vertical Wall-Mounting

Installing the Hub on a Wall FastHub 400 10/100 Series Installation and Configuration Guide 2-12 Installing the Hub on a Wall This section describes how to attach the hub in parallel and vertically to a wall. Note Be sure the hub is powered off and is not connected to a power source before you perfo...

Page 13 - Attaching the Hub to a Wall; vertically attaching the hub to a wall.; Attaching the Hub to the Wall

Installing and Starting Up the Hub 2-13 Attaching the Hub to a Wall Attaching the Hub to a Wall For the best support of the hub and cables, make sure the hub is securely attached to a wallstud or to a firmly attached plywood mounting backboard, as shown in Figure 2-7. Youmust supply your own screws ...

Page 14 - Connecting to the Console Port (FastHub 400M Models); data bits

Connecting to the Console Port (FastHub 400M Models) FastHub 400 10/100 Series Installation and Configuration Guide 2-14 Connecting to the Console Port (FastHub 400M Models) To connect the RJ-45 console port of a FastHub 400M model to a management station ormodem, you must use the supplied RJ-45-to-...

Page 16 - Assigning IP Information to the Hub (FastHub 400M Models); Hub IP address

Assigning IP Information to the Hub (FastHub 400M Models) FastHub 400 10/100 Series Installation and Configuration Guide 2-16 Assigning IP Information to the Hub (FastHub 400MModels) After you install the hub and connect it to a management station, you can assign IPinformation to the hub. IP informa...

Page 17 - If the management station from which the FastHub 400 series Hub; The following information is displayed:; Pressing Return opens a CLI session.; Exit from the terminal session.

Installing and Starting Up the Hub 2-17 Assigning IP Information to the Hub (FastHub 400M Models) Step 5 Enter the IP address of the default gateway (for example: 10.1.105.254): Enter IP default gateway: 10.1.105.254 Note If the management station from which the FastHub 400 series Hub Manager is use...

Page 18 - Connecting to the 10/100 Network Ports and Uplink Port; — 10BaseT network devices—Category 3, 4, or 5

Connecting to the 10/100 Network Ports and Uplink Port FastHub 400 10/100 Series Installation and Configuration Guide 2-18 Connecting to the 10/100 Network Ports and Uplink Port You can connect the 10/100 network ports and the uplink port to the ports on any 10BaseTor 100BaseTX network device, such ...

Page 19 - — Let both ports autonegotiate port speed.; Caution; Follow these steps to connect to 10BaseT or 100BaseTX devices:

Installing and Starting Up the Hub 2-19 Connecting to the 10/100 Network Ports and Uplink Port • Connecting to devices that do not autonegotiate or that have their speed setting manuallyset can reduce performance or result in no link. To maximize performance, choose oneof these methods for configuri...

Page 20 - Accessing the Management Interfaces (FastHub 400M Models); If the port LED does not come on, check for the following problems:

Accessing the Management Interfaces (FastHub 400M Models) FastHub 400 10/100 Series Installation and Configuration Guide 2-20 Step 2 Connect the other end of the cable to the 10BaseT or 100BaseTX port of thenetwork device. Step 3 Check to see that the port LED for the port that you connected in Step...

Page 21 - Accessing the FastHub 400 Series Hub Manager; To access the hub manager, follow these steps:

Installing and Starting Up the Hub 2-21 Accessing the FastHub 400 Series Hub Manager Accessing the FastHub 400 Series Hub Manager To access the hub manager, all you need is the IP information of the hub (and the passwordif one has been assigned). IP information for the hub is usually assigned when t...

Page 22 - Home Page

Accessing the Management Interfaces (FastHub 400M Models) FastHub 400 10/100 Series Installation and Configuration Guide 2-22 Figure 2-10 Home Page Note You can bookmark the hub IP address to retrieve the hub manager for later use. If you are using Communicator, choose the Communicator menu option, ...

Page 23 - Accessing the CLI; You can access the CLI; Accessing the MIB Files through SNMP

Installing and Starting Up the Hub 2-23 Accessing the CLI Accessing the CLI You can access the CLI • From a console terminal connected to the hub console port. For more information, seethe “Connecting to the Console Port (FastHub 400M Models)” section on page 2-14. • Through a Telnet session from a ...

Page 24 - — Read community string. The default is public.; Using FTP to Access the MIB Files

Accessing the Management Interfaces (FastHub 400M Models) FastHub 400 10/100 Series Installation and Configuration Guide 2-24 • CISCO-SIBU-MANAGERS-MIB.my contains the MIB module for managementinterfaces on the FastHub 400M models. • CISCO-SIBU-STACKABLE-DUAL-SPEED-HUB-MIB.my contains the MIB module...

Page 25 - Using CCO to Access the MIB Files; You can access CCO in the following ways:; Remote Monitoring

Installing and Starting Up the Hub 2-25 Accessing the MIB Files through SNMP Using CCO to Access the MIB Files To access the MIB files from CCO, click Software & Support to display the SoftwareCenter site. CCO serves a wide variety of users through two interfaces that are updated and enhancedsim...

Page 26 - Where to Go Next; RMON Groups and Their Functions; Statistics; per historyControlTable entry.

Where to Go Next FastHub 400 10/100 Series Installation and Configuration Guide 2-26 Where to Go Next Now that you have installed the hub and, if you have a FastHub 400M models, assigned IPinformation to the hub, you can continue to • Chapter 3, “Configuring and Monitoring from the Hub Manager” for ...