Gemini GEM-RP8 - Manuals - manualsarea.com

Page 2 - on the keypad display will be lit. If zone 2 is a motion detector, and; GEMINI Keypad; puts super-simple system control at your fingertips.; Most keypad commands involve; I N T R O D U C T I O N

Congratulations on your purchase of an advanced GEMINI-RP8 keypad. Meticulously developed by a leading manufacturer of state-of-the-art security products, this system will provide you with unprecedented peace-of-mind & incorporates some of the most sophisticated features available today. Above a...

Page 3 - Zone Test; System Information; T A B L E O F C O N T E N T S; TABLE OF CONTENTS

3 Important - Test Your System Weekly! 1 Bell / Battery Test Test your bell or siren by pressing A followed by 1 . This will cause the bell, or siren to sound for 2 seconds and also initiate a test of the battery. 2 Zone Test Walk throughout the premises, opening each protected door or window, and a...

Page 4 - G E M I N I; Status Light; AC Light; will light to indicate; K E Y P A D C O N T R O L S & I N D I C A T O R S

ARM ED C O M P U T E R I Z E D S E C U R I T Y S Y S T E M STA TUS I H G E M I N I 1 2 3 4 5 6 7 8 A 1 2 3 B 4 5 6 C 7 8 9 0 E F G J 4 Status Light will light when all zones are secure and system is ready to be Armed. AC Light will light to indicate that AC Power is present. Trouble Light H will lig...

Page 5 - bypassed; A R M I N G : S E T T I N G T H E A L A R M W H E N L E A V I N G

Arming Your System When Leaving 1 Before arming your system, make sure the green Status light is ON. This indicates that all of your protective zones are secure. If any zones are open, the corresponding Zone number will be lit. Secure these zones before proceeding. If any zones cannot be secured, se...

Page 6 - Protecting Yourself While at Home; Status; Instant Mode; Armed; Easy Exit; A R M I N G : P R O T E C T I N G Y O U R S E L F A T H O M E

Protecting Yourself While at Home 1 Before arming your system, make sure the green Status light is ON. This indicates that all of your protective zones are secure. If any zones are open, the corresponding zone number will be lit. Secure those zones before proceeding. 2 Enter your User Code and press...

Page 7 - Ambush Alarm; E M E R G E N C Y C O N D I T I O N S

Emergency Buttons 7 8 9 G The three sets of emergency buttons, if programmed, are always active whether the system is armed or disarmed. Discuss these Buttons with your installer. The emergency signal will only be activated when the two respective buttons are pressed at the same time. Fire Alarm: Si...

Page 8 - Disarming Your System when Returning; Alarm Indication; Silencing an Alarm; Abort Delay; T U R N I N G O F F T H E A L A R M ( D I S A R M I N G ) W H E N R E T U R N I N G

Disarming Your System when Returning 1 Enter your premises through the Entry/Exit door. The keypad will sound a steady tone to remind you to disarm the system before your Entry Delay time expires. 2 Enter your User Code and press D . The red Armed light will go out, indicating that the system has be...

Page 9 - F I R E P R O T E C T I O N

Preparing a Fire Escape Plan Even with the most advanced fire alarm system, adequate protection requires an escape plan. To prepare your plan, draw floor plans of your building (space is provided on the next page). Show two exits-a front or back door and a window from each room. (Make sure each wind...

Page 10 - Floorplan; Draw a plan of your premises below.

10 Floorplan Draw a plan of your premises below. F I R E P R O T E C T I O N

Page 11 - that; F U N C T I O N M E N U

By pressing A followed by the the appropriate key, (do not press simultaneously) these special functions and features can be enabled: Easy Arm (when system is disarmed) The Easy Arm feature allows the system to be armed by pressing A followed by 0 . This will allow the easy arming of the system by s...

Page 12 - S Y S T E M T R O U B L E S

12 The Control Panel is constantly monitoring its own components, as well as all critical services, such as AC power and the telephone line, to insure that it is always ready to provide the protection for which it was designed. When a system trouble does occur, it will caution you by lighting the TR...

Page 14 - P R O G R A M M I N G ( O P T I O N A L )

Your Installer has assigned a User 1 Code which can be used to not only Arm and Disarm the system, but also to enter the User Program Mode, where you can program other user codes. The following explains how you will use this code to program or erase additional user codes. Entering the User Program M...

Page 15 - G L O S S A R Y

Ambush Code - In the event that you are forced by an intruder to disarm your system, this special code can be used t o d i s a r m t h e s y s t e m , a n d simultaneously send a silent alarm to Central Station. If your system has the Ambush feature enabled, the code assigned as the User 8 code will...

Page 16 - NAPCO LIMITED WARRANTY

NAPCO LIMITED WARRANTY THE FOLLOWING STATEMENT IS REQUIRED BY THE FCC . This equipment generates and uses radio-frequency energy and, if not installed and used properly, that is, in strict accordance with the manufacturer's instructions, may cause interference to radio and television reception. It h...