Gasmate BQ1090BNG - Manuals

Page 2 - READ ME FIRST; GAS LEAK TESTING

3 2 READ ME FIRST GAS LEAK TESTING It is important that you leak test the BBQ before first use and every time the gas cylinder is refilled and reconnected to the BBQ. To Complete Leak Test • Make sure all the control knobs are OFF.• In a small container, mix up a solution of water and detergent/soap...

Page 3 - GENERAL INFORMATION; IF THERE IS A LEAK

3 2 FOR YOUR SAFETY Failure to comply with these instructions could result in a fire or explosion which could cause serious bodily injury, death or property damage. CAUTION: Accessible parts may be very hot. Keep young children away.Any modifications of this barbecue may be dangerous.DO NOT move thi...

Page 5 - ELECTRICAL INFORMATION

5 4 IMPORTANT SAFEGUARDS READ THESE INSTRUCTIONS CAREFULLY BEFORE USING THE PRODUCT. KEEP THE INSTRUCTIONS HANDY FOR FUTURE REFERENCE. Important: Always operate the Product from a power source of the same Voltage, Frequency and Rating as indicated on the Product Identification Plate. • DO NOT operat...

Page 7 - LIGHTING PROCEDURE; Burner Operation & Ignition System Check; Ignition system check

7 6 LIGHTING PROCEDURE Burner Operation & Ignition System Check 1. Turn the control knobs clockwise to “OFF” position. 2. Connect the regulator to the gas bottle. Turn the gas supply “ON” at the cylinder. Check with the use of soapy water for any gas leakage between the bottle and the regulator ...

Page 8 - OPERATING PROCEDURE

9 8 Problem Possible Reason Solution Food is not cooking or is taking too long Burner has gone out Check that the gas bottle is not empty and re-ignite the burner Cooking surface was not given enough time to warm up before the food was applied Remove the food and give the burner time to warm the coo...

Page 10 - WARNING; CLEANING THE BURNER

11 10 WARNING Beware of spiders and wasps. Burner tube should be inspected and cleaned periodically.To avoid any flare-ups, it is recommended that the drip tray be checked and emptied regularly. Contents of the drip tray may be very hot during cooking. If emptied during extended cooking extreme caut...

Page 12 - ASSEMBLY INSTRUCTIONS; STEP 2

13 12 ASSEMBLY INSTRUCTIONS IMPORTANT: Remove any transit protection material before use. Tools required: 3. Unscrew ignition cap and place a Battery (Size: AA) into place withthe (+) end facing outwards. Screw cap back on. Upon pressing the ignition button, you should hear a clicking sound. 4. For ...

Page 15 - BUILT-IN BBQ DIMENSIONS; MUST NOT BE COMBUSTIBLE.

15 14 BUILT-IN BBQ DIMENSIONS 1488 (BQ1090B) 770mm MINIMUM GAS CYLINDER NOT TO BE INSTALLED UNDERNEATH 150mm MINIMUM NOTE: TO BE INSTALLED BY AN AUTHORISED PERSON. PLEASE NOTE: MINIMUM CLEARANCE TO COMBUSTIBLES UNDER FAT TRAY IS 150mm. THE MATERIAL FOR THE CABINET (ISLAND) MUST NOT BE COMBUSTIBLE.

Page 16 - NATURAL GAS CONVERSION

17 16 NATURAL GAS CONVERSION TO BE INSTALLED ONLY ON OR IN A NON-COMBUSTIBLE ENCLOSURE Note: Recommended clearances must be maintained. Tools Required: 7mm Drill, Thin (2.5mm diameter) flat Screw Driver, Adjustable spanner, Phillips head screw driver. GAS PIPING 1. THIS APPLIANCE IS ONLY TO BE INSTA...

Page 17 - following will apply:; SAFE APPLIANCE LOCATIONS; DIAGRAMMATIC REPRESENTATIONS OF OUTDOOR AREAS

17 16 This appliance shall only be used in an above ground open-air situation with natural ventilation, without stagnant areas, where gas leakage and products of combustion are rapidly dispersed by wind and natural convection. Any enclosure in which the appliance is used shall comply with the follow...

Page 18 - Tools Required

19 18 ASSEMBLY INSTRUCTIONS Tools Required Standard Phillips-head screw driver.To join your kitchen together use 2 wing screws and nuts as shown. IMPORTANT Remove all packing and transit protection before assembly. CAUTION: Ensure no packing material is left in BBQ before lighting.

Page 23 - BQ1095 - TOP FOR 2 DOOR BAR FRIDGE

23 22 BQ1095 - TOP FOR 2 DOOR BAR FRIDGE Rest the Frame top onto the fridge, with the front fascia overhanging at the front. Push the frame backwards until the front of the frame catches under the front of the fridge. Attach the brackets to the underside of the frame using the screws provided (as sh...

Page 24 - For any queries or assistance call; Customer Service; Keep your purchase receipt, this will be required to

24 24 For any queries or assistance call Customer Service (Australia Only) 1300 174 876 Hours of operation: Monday to Friday 8.30am - 5.30pm EST Do not return to place of purchase. Keep your purchase receipt, this will be required to make any claims under the 12 month warranty.