Garland GAS PIZZA OVENS - Manuals

Page 2 - IMPORTANT INFORMATION; Keep appliance area free and clear from combustibles

Part # 1844063 (08/06) Page 2 IMPORTANT INFORMATION WARNING: This product contains chemicals known to the State of California to cause cancer and/or birth defects or other reproductive harm. Installation and servicing of this product could expose you to airborne particles of glass wool/ceramic ﬁbers...

Page 3 - TABLE OF CONTENTS

Part # 1844063 (08/06) Page 3 TABLE OF CONTENTS Important Information . . . . . . . . . . . . . . . . 2 Dimensions And Speciﬁcations GPD Series . . . . . . . . . . . . . . . . . . . . . . . . 4 Installation . . . . . . . . . . . . . . . . . . . . . . . . 5 Rating Plate . . . . . . . . . . . . . . . ...

Page 4 - DIMENSIONS AND SPECIFICATIONS GPD SERIES

Part # 1844063 (08/06) Page 4 DIMENSIONS AND SPECIFICATIONS GPD SERIES 3" [76mm] 7-15/16" [201mm] 12-1/2" [318mm] 45-1/4" [1149mm] 8" [203mm] 7-21/32" [195mm] 3/4"N.P.T. [19mm] GASINLET 14-1/2" [368mm] 23-3/8" [594mm] 24-21/32" [626mm] 28-1/2" [724mm] DECK...

Page 5 - INSTALLATION; Rating Plate

Part # 1844063 (08/06) Page 5 INSTALLATION 1. Damage Check: check carton or crate for possible damage incurred in shipping. After carefully uncrating, check for “concealed” damage. Report any damage immediately to your carrier. 2. The correct type of gas for which the unit was manufactured is noted ...

Page 6 - INSTALLATION Continued

Part # 1844063 (08/06) Page 6 B. If it is a new installation, have gas authorities check meter size and piping to assure that the unit is supplied with suﬃcient amount of gas pressure required to operate the unit. C. If it is additional or replacement equipment, have gas authorities check pressure t...

Page 7 - INSTALLATION continued; Installing Under Ventilation Canopy:; ASSEMBLY INSTRUCTIONS; Leg Installation

Part # 1844063 (08/06) Page 7 INSTALLATION continued Termination Less than 10 feet (3 meters) from ridge Termination More than 10 feet (3 meters) from ridge Less than 10 feet (3 meters) More than 10' (3 meters) 2' (60cm) Min. 3' (90cm) Min. 3' (90cm) Min. Installing Under Ventilation Canopy: Too str...

Page 8 - ASSEMBLY INSTRUCTIONS Continued; Double Deck Assembly

Part # 1844063 (08/06) Page 8 ASSEMBLY INSTRUCTIONS Continued 1. Slide the wooden frame out of the oven. 2. Before installing the hearth core plates or steel hearth assembly, be sure that the bottom heat deﬂectors are properly positioned with the treaded side (bumps) in the up position. 3. If the ov...

Page 9 - ADJUSTMENTS; Gas Pressure Adjustments; All gas burners and pilots need sufficient air to; Flame & Air Mixture Adjustment

Part # 1844063 (08/06) Page 9 ASSEMBLY INSTRUCTIONS Continued 7. A separate shut-oﬀ valve for each oven must be provided. It should be as close as possible to the place where the gas line goes into the oven. It must be located so that it is easily accessible. A handle or wrench should be chained to ...

Page 10 - By-Pass Flame Adjustment; NOTE; Calibration; ADJUSTMENTS Continued

Part # 1844063 (08/06) Page 10 good mixture of air and gas. When using LP gas the ﬂame will have a blue yellow appearance. Follow steps  thru  to adjust the ﬂame for good quality. 1. Loosen the small knurled locking disk. 2. Turn the large adjusting disk towards the air mixture throat to reduce th...

Page 11 - Flame Diverters; OPER ATION

Part # 1844063 (08/06) Page 11 ADJUSTMENTS Continued 3. Set the thermostat temperature dial to 500 degrees F (260 degrees C) and allow the oven temperature to stabilize. The thermostat must be allowed to cycle twice before taking a test reading. 4. Check the temperature when the burner just cycles o...

Page 12 - CLEANING; Lighting/Shutdown Instructions; Painted Surfaces; Oven Interior; Aluminized Steel Surfaces; Core Plates; OPER ATION Continued

Part # 1844063 (08/06) Page 12 CLEANING 6. When the oven has reached the selected temperature, experiment until you get the feel of the oven and the speed of the bake. In case of some initial unevenness in the baking, have patience for a few days until the oven cures Lighting/Shutdown Instructions 1...

Page 13 - TROUBLESHOOTING GUIDE

Part # 1844063 (08/06) Page 13 Problem Causes Solutions Hot Spots in Deck Flame diverters not installed properly Push all the way to the back of oven Flame diverters warped or damaged May need replacing Bottoms cook before top Deposit on deck Clean deck Low production oven idling Turn temperature up...

Page 14 - NOTES

Page 15 - E DE

Pièce nº 1844063 (07/05) Page 14 Prob lème Causes Solutions P oints chauds dans la section Les déﬂ ecteurs de ﬂ ammes ne sont pas bien installés P ousser complètement jusqu’au f ond du four Les déﬂ ecteurs de ﬂ amme sont défor més ou endommagés P eut e xiger le remplacement Les fonds cuisent plus vi...

Page 18 - RÉG

Pièce nº 1844063 (07/05) Page 11 Régla ge De La Fla mm e De Dériv ati on : La d éri vat ion d an s le th erm ost at e st un e ali men tat ion en gaz a rrivan t à la c om man de i ndé pen dam men t d u r égl age du cad ran . Cet te a lim en tat ion est c om man dée pa r la vis de r égl age. C ett e p...