Fusion L50B PRO - Manuals - manualsarea.com

Page 3 - SpECIAL FEATUrES; SpEciFicAtions

1 Input Voltage 11~15V DC Battery Type & Cells 1~5 Lithium-Ion or Lithium-Polymer cells (3.6V or 3.7V respectively) 1~6 LiFePO4 cells (3.3V) 1~14 Nickel-Cadmium cells 1~14 Nickel-Metal Hydride cells 1 - 6 Lead-Acid cells (2V per cell) Battery Capacity 100mAh ~ 6000mAh adjustable ONLY for Lithium...

Page 4 - SAFEty prEcAutions

2 SAFEty prEcAutions • DO NOT attempt to charge incompatible types of rechargeable batteries. This charger is designed to only charge and discharge Nickel-Cadmium, Nickel-Metal Hydride, Lithium-Ion, Lithium-Polymer, LiFePO4 and Lead- Acid batteries. • Make sure you place the charger on a firm level ...

Page 7 - Input powEr; Output BAttEry ConnEctions

5 Input powEr 12V DC Connect the charger’s red alligator clip to the positive (+) terminal on the power source and the black alligator clip to the negative (-) terminal. The charger will display “Input voltage” error message if the input is below 11V or above 15V. If this happens, please recheck the...

Page 8 - NiCd Mode; OpErAtion

6 NiCd CHARGE C=3.0A BATT TYPE NiCd CHARGE C=3.0A START BATTERY CHECK WAIT PLEASE.... CHG 0:00 00000 NC+3.00A 5.200V INC DEC ENTER INC DEC NiCd delta-peak- volt = 0mV/cell NiCd delta-peak- volt = 0mV/cell ENTER INC DEC Setting Charge Current Adjust the desired charge current, which ranges from 0.1A ...

Page 9 - NiMH Mode

7 NiMH CHARGE C=3.0A BATT TYPE NiMH CHARGE C=3.0A START BATTERY CHECK WAIT PLEASE.... CHG 0:00 00000 NC+3.00A 5.200V INC DEC ENTER INC DEC NiMH delta-peak- volt = 0mV/cell NiMH delta-peak- volt = 0mV/cell ENTER INC DEC Setting Charge Current Adjust the desired charge current, which ranges from 0.1A ...

Page 10 - Setting Battery Capacity; Setting Battery Voltages For Li-Ion Battery Pack

8 Lilo CHARGE 3.0A C=3000mAh 10.8Vp INC BATT TYPE DEC ENTER Lilo CHARGE 3.0A C=3000mAh 10.8Vp INC DEC START BATTERY CHECK WAIT PLEASE.... CHG 0:00 00000 LI + 3.00A 12.000V Lilo CHARGE 3.0A C=3000mAh 10.8Vp INC DEC Lilo CHARGE 3.0A C=3000mAh 10.8Vp INC DEC BALANCER CON. NOT CONNECTED BALANCER CON. CO...

Page 12 - Setting Charge Current; Battery Pack; Pb Mode

10 PB CHARGE C=3.0A 12Vpack BATT TYPE ENTER PB CHARGE C=3.0A 12Vpack INC DEC START BATTERY CHECK WAIT PLEASE.... CHG 0:00 00000 PB + 3.0 A 12.000V PB CHARGE C=3.0A 12Vpack INC DEC to NiCd charge ENTER Setting Charge Current Adjust the desired charge current, which ranges from 0.1A to 6.0A with the I...

Page 13 - Displays During Charge; ScrEEn DisplAys; Completion Display (with Audible Warning)

11 Displays During Charge ScrEEn DisplAys CHG 0.30:25 00000 NC + 3.00A 5.200V “BLC” will be shown if the balancer cable of the battery is connected to the balancing port of the charger. CHG: Charge NC = NiCd NM = NiMH Ll = Lilo, LP = LiPo, LF = LiFe Pb = Pb If the Enter button is pressed at any stag...

Page 14 - Error mEssAgEs

12 INPUT BATTERY VOLTAGE ERROR Error mEssAgEs NO BATTERY OUTPUT BATTERY REVERSE POLARITY OUTPUT CIRCUIT PROBLEM CHECK THE BATT. OPEN CIRCUIT CHECK THE BATT. OVER VOLTAGE CHECK THE BATT. LOW VOLTAGE BALANCER VOLTAGE IS TOO HIGH BALANCER VOLTAGE IS TOO LOW DON’T CHARGE LiXX WITH THIS MODE Input voltag...

Page 16 - ogic; rC

Logic RC Limited 14 Hartham Lane Herford SG14 1QN United Kingdom www. L ogic rC .com