Furuno GP-90 - Manuals

Furuno GP-90 – Manual in PDF format online.

Manuals:

Manual

Manual Furuno GP-90

Summary

Page 2 - SAFETY INSTRUCTIONS; WARNING; Use the correct fuse.; CAUTION

SAFETY INSTRUCTIONS WARNING Do not work inside the equipment unless totally familiar with electrical circuits. Hazardous voltage which can cause electrical shock, burn or serious injury exists inside the equipment. Turn off the power at the mains switchboard before beginning the installation.Post a ...

Page 3 - LIST; Standards; For DGPS; Options

1 1. EQUIPMENT LIST Standards Name Type Q'ty Mass (kg) Remarks GPA-017S GPA-018S Antenna Unit GPA-019S 1 For DGPS GP-90-N Without Beacon RX Display Unit GP-90-A 1 2.2 With Beacon RX CP20-01900 With Antenna Cable Installation Materials CP20-01950 1 set See lists at end of manual. Without Antenna Cabl...

Page 4 - UNIT; Locate the unit away from exhaust pipes and vents.; Table Top and Overhead Mounting; Display unit mounting methods; Flush mounting type F; Flush mounting type S; Name Type

2 2. DISPLAY UNIT The display unit can be installed with either of four methods as shown below. Refer to the outline drawing at the end of manual. • Locate the unit away from exhaust pipes and vents. • The mounting location should be well ventilated. • Mount the unit where shock and vibration are mi...

Page 5 - Mounting; Select a location out of the radar beam.; The radar beam will obstruct or prevent reception; Be sure the location offers a clean line-of-sight to satellite.; Mounting the antenna as high as possible keeps it free; The antenna unit GPA-018S must be grounded.; Connect ground wire of 1.25 sq or larger; The antenna unit GPA-018S must be taped.; See chapter 7 for instructions.; Extending Antenna Cable Length; Extension cable line-up

3 3. ANTENNA UNIT Mounting Install the antenna unit referring to the installation diagram at end of manual. When selecting a mounting location for the antenna unit, keep in mind the following points. • Select a location out of the radar beam. The radar beam will obstruct or prevent reception of the ...

Page 7 - Connection of cables on display unit

5 4. WIRING The figure below shows the connection of cables on rear of display unit. Ground the display unit toprevent loss of sensitivityand mutual interference. CAUTION Rear of Display Unit Ground External Equipment FUSE 2A Black Red DATA1 DATA3 DATA4 DATA2 INPUT12~24 VDC Antenna Unit GPA-018S GPA...

Page 8 - Grounding; The grounding wire should be 1.25sq or larger.; External Equipment; Connection of DATA4 port; In case of RS-422 Level

4. W IRING 6 Grounding The display unit contains several CPUs. W hile they are operating, they radiate noise, which can interfere with other radio equipment. Ground the unit as follows to prevent it. • The grounding wire should be 1.25sq or larger. • The grounding wire should be as short as possible...

Page 9 - SETTINGS; Checking Operation; Self-test display at equipment start up; DGPS Setup; Automatic DGPS setup; Figure 5-1 DGPS SETUP menu

7 5. INITIAL SETTINGS Checking Operation 1. Turn on the GP-90. 2. Confirm that "OK" and "BEACON RCVR INSTALLED" are displayed on the self-test display. Confirm that "BEACON RCVRINSTALLED" is displayed whenDGPS function is provided. BEACON RCVR INSTALLEDDATA 3: DATA OUTPUT PRO...

Page 11 - Input/Output Setting; Talker

5. INITIAL SETTINGS 9 Input/Output Setting The GP-90 can output navigation information to external equipment. For example, it can output position data to a radar or echo sounder for display on their display screen. You can convert a Loran Plotter to a GPS Plotter with position data from the GP-90. B...

Page 12 - Data format and data output availability; RMC: Recommended minimum specific GPS/TRANSIT data

5. INITIAL SETTINGS 10 Data format and data output availability Output data sentence of IEC 61162-1 and NMEA 0183 Ver. 1.5/2.0. AAM: Waypoint arrival alarm APB: Autopilot sentence B magnitude of cross track error, direction to steer, arrival alarm, bearing to waypoint ("Heading to steer to desti...

Page 14 - General data; ) Input of waypoint data; Rate of operation

5. INITIAL SETTINGS 12 AGFPA: Autopilot information from FURUNO autopilot equipments Port Input Output DATA1 DATA2 NMEA 0183 Ver. 1.5 /2.0 AGFPA , DBT, DPT, HDG, HDM, HDT, MTW, TLL, VBW, VHW IEC 61162-1/NMEA 0183 Ver.1.5/ Ver.2.0 AAM, APA, APB, BOD, BWC, BWR, BWW, GGA, GLL, GNS, RMB, RMC, VDR, VTG, ...

Page 15 - DATA 1 output setting; or

5. INITIAL SETTINGS 13 DATA 1 output setting 1) Press [MENU], [9] and [3]. The DATA 1, 3 OUTPUT SETUP menu appears. Talker ID GP LC DE Output Data (00-90 sec) 100% 1. AAM:00 APA:00 APB:04 BOD:00 2. BWC:00 BWW:00 GGA:00 GLL:01 3. RMB:01 RMC:00 VTG:01 WCV:00 4. VDR:00 WPL:00 XTE:00 ZDA:01 5. GNS:00 GB...

Page 16 - DATA 2 output setting; Figure 5-4 DATA 2 OUTPUT SETUP menu; DATA 3 output setting; Selection of NMEA0183 or log pulse

5. INITIAL SETTINGS 14 DATA 2 output setting 1) Press [MENU], [9] and [4]. The DATA 2 OUTPUT SETUP menu appears. Talker ID GP LC DE Output Data (00-90 sec) 100% DATA2 OUTPUT SETUP MENU : Escape ENT : Enter Data Fmt. V1.5 : Select Setting shown here are default settings. 1. AAM:00 APA:00 APB:04 BOD:0...

Page 17 - Setting DATA 4 to Data Output

5. INITIAL SETTINGS 15 Setting DATA 4 to Data Output 1) Press [MENU], [9] and [5]. The DATA 4 I/O SETUP menu appears. DATA 4 I/O SETUP 1/2 To Next Page ENT : Enter MENU : Escape Appears only when externalDGPS receiver is used. DATA 4. Level RS232C RS422 Data Out Com. DGPS : Select Figure 5-5 DATA 4 ...

Page 19 - Setting DATA 4 to DGPS

5. INITIAL SETTINGS 17 14) Output data from the computer. When loading data is completed, the cursor shifts to Stop. 15) Press the [ESC] key. Setting DATA 4 to DGPS An external DGPS receiver can be connected to the DATA 4 port. Follow the procedure below to setup the GP-90 according to the specifica...

Page 20 - DGPS; Beacon Receiver Set GR-80; Signal level

18 6. OPTIONAL DGPS Beacon Receiver Set GR-80 GP-90 GR-80 DATA DATA4 NP Board JP3 Open TD-ATD-BRD-ARD-B GND RD-ARD-BTD-ATD-BGND 1234567 43217 RS-422* RS-422 * This connection is required for L/L Auto mode of GR-80. WhipAntenna Preamp unit (with15 m cable) WHT BLK YEL GRNBLU P P When the GP-90 is con...

Page 21 - TAPING ANTENNA UNIT GPA-018S; the last wind of butyl tape and then back to the base.; ) Squeeze edges of tape with thumb and index finger.

19 7. TAPING ANTENNA UNIT GPA-018S After inserting the whip antenna to the antenna base of GPA-018S, tape the antenna base and whip antenna with self-vulcanizing tape and vinyl tape to reinforce the whip antenna. 1. Wrap the antenna junction point with butyl 15 tape or the equivalent. How to wrap 1)...

Page 24 - 工事材料表; 工事材料表; Antenna Cable Set

CODE NO. 004‑372‑420‑00 TYPE CP20‑01701 略図 OUTLINE 名称 NAME 数量 Q'TY 用途／備考 REMARKS 番号 NO. 型名／規格 DESCRIPTIONS 1/1 ‑4 INSTALLATION MATERIALS 工事材料表 20AG‑X‑9405 変換ｹｰﾌﾞﾙ組品 CONVERT CABLE ASSY. NJ‑TP‑3DXV‑1 2 000‑123‑809‑00 1 CODE NO. ﾋﾞﾆﾙﾃｰﾌﾟ VINYL TAPE NO360 0.2X19X10000 1 000‑835‑215‑00 2 CODE...