Furuno GP-1610C - Manuals - manualsarea.com

Page 2 - Electrical shock can result.; Keep heater away from equipment.; WARNING; SAFETY INSTRUCTIONS

2 Do not disassemble or modify theequipment. Fire, electrical shock or serious injurycan result. Turn off the power immediately if waterleaks into the equipment or the equip-ment is emitting smoke or fire. Continued use of the equipment can causefire or electrical shock. Do not place liquid-filled c...

Page 3 - Inserting a Chart Card; Open the chart card drive cover at the bottom of the display unit.; Insert chart card label side up, arrow forward.; Close the chart card drive cover.; To eject a chart card:; Open the chart card drive cover.; Note: If no chart card is inserted a general world map appears.

3 Inserting a Chart Card 1 Turn off the power. 2 Open the chart card drive cover at the bottom of the display unit. Screws Cover 3 Insert chart card label side up, arrow forward. EJECTbutton Chartcard Arrow forward 4 Close the chart card drive cover. To eject a chart card: 1 Open the chart card driv...

Page 4 - Displaying the Plotter Picture

4 Displaying the Plotter Picture Press the POWER key to turn on the equipment. A beep sounds and shortly thereafter theplotter display appears. Results of self-test;displayed for aboutone second. Warning on chartcard usage; appearsfor about one minute. ACQ means acquiringsatellite; position isnot re...

Page 5 - Adjusting Tone and Brilliance; Press

5 Adjusting Tone and Brilliance TONE : 5 ■■■■■□□□□□ BRILL : 8 ■■■■■■■■ LOW HIGH LOW HIGH 1 Press the TONE key. 2 Press t or s to adjust tone. 3 Press ▲ or ▼ to adjust brilliance. Adjust tone or brilliancewithin 10 seconds,otherwise the displaywill be erased. Ten levels of tone areprovide...

Page 6 - How to Use the Cursor

6 How to Use the Cursor 1 Press ▲ ▼ t s . Position Cursor position is digi-tally displayed on thescreen. The CURS key alternately displays anderases the cursor. BRG+ 232.0° RNG+ 0.00nm 2DDEP 110 m TMP - - .-°C 13:55+ 34°43.801'N 135°21.163'E Cursor intersection Cursor positionin lattitude andlo...

Page 7 - Registering Your Harbor; Date and time of

7 Registering Your Harbor By registering your harbor as a waypoint, you can later use it as a destination waypoint, whenreturning home. 1 Press the WPT key. 3 Press the ENT key. SELECT WPT MODE WPT at Own Position CSE 180.0° SPD 0.0kt 2DDEP 110 m TMP - - .-°C 14:35POS 34°26.345'N 135°41.2...

Page 8 - Setting Destination; Press the ZOOM OUT key.

8 Setting Destination When you set a destination, this unit computes the range, bearing and course to the destina-tion. To display your destination on the screen select a small display range or scale. To set asdestination a point which is 20 nm from your harbor do the following: CSE 180.0 ° SPD 0.0k...

Page 9 - Own ship’s

9 3 Press the ENT key. 4 Place cursor on destination. 5 Press the ENT key twice. 00 WP801 175.0 ° 15nm CSE 180.0 ° SPD 0.0kt 2D DEP 110 m TMP - - .- ° C 14:57 POS 34 ° 26.345’N 135 ° 41.232’E Own ship’s position Course Bearing and range to destination Destination : CursorENT: SetENT twice: completeM...

Page 10 - Sailing for Destination; Steer towards destination.

10 Sailing for Destination Steer towards destination. 00 WP801 175.0 ° 14.7nm CSE 175.0 ° SPD 16.8kt 2D DEP 110 m TMP - - .- ° C 15:00 POS 34 ° 26.345’N 185 ° 41.232’E 00 WP801 175.0 ° 15nm CSE 180.0 ° SPD 16.8kt 2D DEP 110 m TMP - - .- ° C 15:00 POS 34 ° 26.345’N 185 ° 41.232’E Steer towards destin...

Page 11 - Arriving at Destination; When nearing your destination, expand the range scale.; Press the ZOOM IN key.

11 MENU ESC DISPSEL 1 EVENT MOB 6 WPT 2 GOTO 7 MARK 3 PLTR 8 ZOOMOUT 9 CNTR 5 CLR TONE POWER ZOOMIN 4 CURS 0 NU/CU ENT 1 Arriving at Destination When nearing your destination, expand the range scale. Expand thedisplay range orscale. 1 Press the ZOOM IN key. WP801 173.0 ° 5.2nm CSE 160.0 ° SPD 16.8kt...

Page 12 - Entering Marks

12 Entering Marks Marks may be used to denote the location of fish schools, good fishing spots, reefs, etc. 1 Press the MARK key. WP801 173.0 ° 5.2nm CSE 173.0 ° SPD 16.8kt 2D DEP 110 m TMP - - .- ° C 16:01 POS 33 ° 33.979’N 137 ° 07.290’E WP801 170.0 ° 4.8nm CSE 171.0 ° SPD 16.8kt 2D DEP 110 m TMP ...

Page 13 - Changing Mark Shape, Color

13 Changing Mark Shape, Color You may wish to display marks in different shapes and colors to differentiate between reefsand fish schools, for example. The procedure below shows how to change from red circle togreen diamond. CSE 170.0 ° SPD 16.8kt 2D DEP 110 m TMP - - .- ° C 16:09 POS 33 ° 26.154’N ...

Page 15 - Returning to Harbor

15 Returning to Harbor Set your harbor as destination, and the course, range and bearing to it are displayed on thescreen. 1 Press the GOTO key. 3 Press the ENT key. Set waypoint 01,which you entered earlier,as destination. 4 Press the ENT key. CSE 320.0 ° SPD 0.0kt 2D DEP 110 m TMP - - .- ° C 17:30...

Page 16 - After arriving, press the

16 6 Press the CLR key. 7 Press the ENT key. 8 Press the ESC key. 9 Press the POWER key. Cancel destina-tion; turn offthe equipment. SELECT GOTO MODE WPT List EVENT ListROUTE List Cursor/Route plan ENT: Sel CLR: Release ESC: Cancel 5 After arriving, press the GOTO key. Destination is cancelledand co...