Frigidaire FH36DD50MS- Manuals

Page 2 - WELCOME & CONGRATULATIONS; Register Your Product; This unit is intended for

Do not, under any circumstances, cut, remove, or bypass the grounding prong. Power supply cord with 3-prong grounding plug Grounding type wall receptacle 2 WELCOME & CONGRATULATIONS WARNING Improper grounding can result in a risk of electric shock. Consult a qualified electrician if the groundin...

Page 3 - IMPORTANT SAFETY INSTRUCTIONS; WARNING; DEFINITIONS; CAUTION

3 IMPORTANT SAFETY INSTRUCTIONS WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: • Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer at the address or telephone number in the warranty. • Befo...

Page 4 - SHIPPING PACK; IMPORTANT

Tools You Will Need • Phillips Screwdriver • 1/4” Nut Driver / Ratchet • Tape Measure • Carpenter Square • Vertical Level or Plum Line • Tools required to cut countertop Hardware (User Supplied) • (4) Screws appropriate for mounting stabilizing brackets to cabinet material / substrate. 4 SHIPPING PA...

Page 5 - PRODUCT DIMENSIONS; Model; Downdraft Top Trim; Cutout Dimensions

5 PRODUCT DIMENSIONS Model A B C D E Rise FH30DD50MS 30” (76.2 cm) 26 7 / 8 ” (68.3 cm) 17 13 / 16 ” (45.2 cm) 34 5 / 16 ” (87.2 cm) 2 3 / 16 ” (5.5 cm) 10” (25.4 cm) FH36DD50MS 36” (91.4 cm) 32 7 / 8 ” (83.6 cm) A B C E D Rise 1 7 / 16 ” (3.6 cm) 2 1 / 4 ” (5.7 cm) 11 7 / 16 ” (29.0 cm) Telescopic ...

Page 6 - PLANNING; Basic Information

6 PLANNING Basic Information A qualified technician must complete the installation of this appliance. This downdraft blower system is designed to be used to exhaust airborne contaminants when cooking with a variety of gas, electric or induction cooktops. It can be mounted in island, peninsula, or co...

Page 7 - Plan the Ductwork; Plan the Discharge; NOTE

7 Plan the Ductwork This downdraft blower system is designed for use with 3¼ x 10” ductwork (can be transitioned to 6” round). For best performance, choose the ducting option which allows the shortest length of ductwork and a minimum number of elbows and transitions. The system will operate most eff...

Page 8 - Plan the Electrical Connection; Electrical Outlet Location

8 Plan the Electrical Connection The downdraft blower system draws 2.8 AMPS and requires a 120 VAC, 60 Hz circuit. The unit has a 28 inches long power cord with a 3 pronged plug. Plan to provide a grounded outlet in a location which will allow the unit’s power cord to reach. PLANNING  NOTE If the 3...

Page 9 - INSTALLATION

9 1. Cut Countertop Opening - Lay out and cut the cooktop cut-out far enough forward so downdraft will fit behind it (refer to cooktop installation instructions).- Set cooktop in place and slide it as far forward as possible. Center and square it with edges of countertop. 3. Prepare the Downdraft Bl...

Page 10 - Install Duct Transition to Blower; Lower stabilizing brackets Down and Right; DO NOT; Screw Top; Upper stabilizing brackets:

10 4. Install Duct Transition to Blower Install the duct transition on the blower, using the three wide head Phillips screws. It is recommended for all duct joints, the seam between the blower and the duct transition should be sealed with duct tape over the screws. R e m o v e s c r e w s f r o m t ...

Page 11 - Connect Downdraft to Power

DUCT TAPE OVER SEAM AND SCREW Screw Air Flow Duct Tape Over Seam and Screw DUCT ON-THE-FLOOR DUCT THROUGH-THE-FLOOR 11 6. Install Ductwork - Use galvanized or aluminum duct in 6” round or 3 ¼ ” x 10” size, or a combination of both. PVC duct should be used if installing under a poured concrete slab. ...

Page 12 - Calculating Duct Length Table

DUCT PIECES E QUIVALENT LENGTH X NUMBER USED = EQUIVALENT LENGTH 6" (15.2cm) Round Straight ** 1 Ft. (0.3m) Ft. or m 6" (15.2cm) Round Metal Flex No Bends ** 1.5 Ft. (0.45m) Ft. or m 6" (15.2cm) 90° Elbow 10 Ft. (3m) Ft. or m 6" (15.2cm) 45° Elbow 5 Ft. (1.5m) Ft. or m 3¼" x 10&#...

Page 15 - BEFORE YOU CALL

15 BEFORE YOU CALL (Solutions to Common Problems) OCCURRENCE POSSIBLE CAUSE/SOLUTION Telescoping Vent does not fully raise Check for and remove obstructions. The telescoping vent is designed to tilt and stop with obstructions. The raise/lower push button will reverse direction of travel and reset th...

Page 16 - MAJOR APPLIANCE WARRANTY

16 MAJOR APPLIANCE WARRANTY This warranty does not cover the following: 1 Products with original serial numbers that have been removed, altered or cannot be readily determined. 2 Product that has been transferred from its original owner to another party or removed outside the USA or Canada. 3 Rust o...