Frigidaire FH36DD50MS- User Manual

5 PRODUCT DIMENSIONS Model A B C D E Rise FH30DD50MS 30” (76.2 cm) 26 7 / 8 ” (68.3 cm) 17 13 / 16 ” (45.2 cm) 34 5 / 16 ” (87.2 cm) 2 3 / 16 ” (5.5 cm) 10” (25.4 cm) FH36DD50MS 36” (91.4 cm) 32 7 / 8 ” (83.6 cm) A B C E D Rise 1 7 / 16 ” (3.6 cm) 2 1 / 4 ” (5.7 cm) 11 7 / 16 ” (29.0 cm) Telescopic ...

6 PLANNING Basic Information A qualified technician must complete the installation of this appliance. This downdraft blower system is designed to be used to exhaust airborne contaminants when cooking with a variety of gas, electric or induction cooktops. It can be mounted in island, peninsula, or co...

7 Plan the Ductwork This downdraft blower system is designed for use with 3¼ x 10” ductwork (can be transitioned to 6” round). For best performance, choose the ducting option which allows the shortest length of ductwork and a minimum number of elbows and transitions. The system will operate most eff...

8 Plan the Electrical Connection The downdraft blower system draws 2.8 AMPS and requires a 120 VAC, 60 Hz circuit. The unit has a 28 inches long power cord with a 3 pronged plug. Plan to provide a grounded outlet in a location which will allow the unit’s power cord to reach. PLANNING  NOTE If the 3...

9 1. Cut Countertop Opening - Lay out and cut the cooktop cut-out far enough forward so downdraft will fit behind it (refer to cooktop installation instructions).- Set cooktop in place and slide it as far forward as possible. Center and square it with edges of countertop. 3. Prepare the Downdraft Bl...

10 4. Install Duct Transition to Blower Install the duct transition on the blower, using the three wide head Phillips screws. It is recommended for all duct joints, the seam between the blower and the duct transition should be sealed with duct tape over the screws. R e m o v e s c r e w s f r o m t ...

DUCT TAPE OVER SEAM AND SCREW Screw Air Flow Duct Tape Over Seam and Screw DUCT ON-THE-FLOOR DUCT THROUGH-THE-FLOOR 11 6. Install Ductwork - Use galvanized or aluminum duct in 6” round or 3 ¼ ” x 10” size, or a combination of both. PVC duct should be used if installing under a poured concrete slab. ...

DUCT PIECES E QUIVALENT LENGTH X NUMBER USED = EQUIVALENT LENGTH 6" (15.2cm) Round Straight ** 1 Ft. (0.3m) Ft. or m 6" (15.2cm) Round Metal Flex No Bends ** 1.5 Ft. (0.45m) Ft. or m 6" (15.2cm) 90° Elbow 10 Ft. (3m) Ft. or m 6" (15.2cm) 45° Elbow 5 Ft. (1.5m) Ft. or m 3¼" x 10&#...

15 BEFORE YOU CALL (Solutions to Common Problems) OCCURRENCE POSSIBLE CAUSE/SOLUTION Telescoping Vent does not fully raise Check for and remove obstructions. The telescoping vent is designed to tilt and stop with obstructions. The raise/lower push button will reverse direction of travel and reset th...

16 MAJOR APPLIANCE WARRANTY This warranty does not cover the following: 1 Products with original serial numbers that have been removed, altered or cannot be readily determined. 2 Product that has been transferred from its original owner to another party or removed outside the USA or Canada. 3 Rust o...