Ford 307-01-1 - Manuals

307-01-5 307-01-5 Automatic Transaxle/Transmission ASSEMBLY (Continued) 17. Install the low/reverse brake drum. 14. CAUTION: The tabs on the output shaft thrust washer (No. 11) point into the • Rotate the low/reverse brake drum clockwise case. Make sure the thrust washer is to install. correctly sea...

307-01-6 307-01-6 Automatic Transaxle/Transmission ASSEMBLY (Continued) 20. Install the reverse band actuating lever shaft into the case and into the reverse band actuatinglever. 24. NOTE: Install the output shaft sleeve with the cone facing up. This sleeve will snap into placewhen correctly install...

307-01-7 307-01-7 Automatic Transaxle/Transmission ASSEMBLY (Continued) 29. Install the spacer on the input shell, using 26. CAUTION: Make sure the needle petroleum jelly to hold it in place. bearings stay in place. Install the low/reverse planetary assembly. 30. Install the input shell and sun gear...

307-01-9 307-01-9 Automatic Transaxle/Transmission ASSEMBLY (Continued) 38. Install the intermediate servo piston and spring. 41. Using a depth micrometer with an 8-inch extension, measure from the top of the gauge • Lubricate the servo bore with clean bar to center support ledge in case at 4 places...

307-01-10 307-01-10 Automatic Transaxle/Transmission ASSEMBLY (Continued) 43. NOTE: Align the disc holes on special tool 44. Add dimension B to C, divide by 2 and record with the slot in gauge bar for correct as dimension D. measurement. 45. Subtract A from D, and record as dimension E. Measure the ...

307-01-11 307-01-11 Automatic Transaxle/Transmission ASSEMBLY (Continued) 48. Install the intermediate band anchor strut. 51. Loosely install the screw. 49. CAUTION: To avoid a ‘‘fall-out’’ condition of the strut from the screw duringassembly and function, the small ‘‘U’’ shapenotch should be toward...

307-01-13 307-01-13 Automatic Transaxle/Transmission ASSEMBLY (Continued) 58. CAUTION: Install the center support retaining ring with the tapered side facingup. CAUTION: Make sure the notch opening is not obstructed by the centersupport retaining ring. Install the center support retaining ring. 1 Ma...

307-01-16 307-01-16 Automatic Transaxle/Transmission ASSEMBLY (Continued) 74. NOTE: Align the disc holes on special tool 72. CAUTION: If the strut is installed with the slot in gauge bar for correct incorrectly, transmission damage will occur. measurement. Check to make sure that the overdrive band ...

307-01-17 307-01-17 Automatic Transaxle/Transmission ASSEMBLY (Continued) Service Part Number Dimension D (7D014) Bearing Thickness Identification (Color/ID) 38.29-38.42 mm F7TZ-NA 1.85-1.90 mm (0.073-0.075 Red (1.51 in) in) 38.43-38.61 mm F7TZ-RA 2.05-2.10 mm (0.081-0.083 Black (1.51-1.52 in) in) 3...

307-01-18 307-01-18 Automatic Transaxle/Transmission ASSEMBLY (Continued) 82. CAUTION: The special tools must be used to correctly align the pump with theadapter plate to reduce gear noise, bushingfailure and leakage. Using the special tool, align the fluid pump tothe adapter plate. 85. CAUTION: Do ...

307-01-19 307-01-19 Automatic Transaxle/Transmission ASSEMBLY (Continued) 86. CAUTION: The overdrive servo must be installed prior to band adjustment. Using the special tool, tighten the overdriveband adjustment screw. Then back off thescrew exactly 1.5 turns and hold that position. • Tighten to 14 ...

307-01-22 307-01-22 Automatic Transaxle/Transmission ASSEMBLY (Continued) 99. CAUTION: Inspect the transmission case bore to make sure it is free of debrisand not damaged. If damaged, transmissionleak may occur. Install the solenoid body. Tighten the screws insequence shown. • Tighten to 8 Nm (71 lb...

307-01-23 307-01-23 Automatic Transaxle/Transmission ASSEMBLY (Continued) 104. Install the parking pawl assembly and gasket. 107. Using the special tools, install the output shaft flange. 1 Install the parking pawl shaft. 2 Install the parking pawl return spring. 3 Install the parking pawl. 4 Instal...

307-01-24 307-01-24 Automatic Transaxle/Transmission ASSEMBLY (Continued) 112. Using the special tool, make sure that the fluid 110. CAUTION: Tightening one screw pump gear seal ring is fully seated. before tightening the other may cause thesensor to bind or become damaged. NOTE: The manual lever mu...