Ford 2005 Explorer v.1- Manuals

Please read the section Supplemental restraint system (SRS) in the Seating and Safety Restraints chapter. Failure to follow the specific warnings and instructions could result in personal injury. Front seat mounted rear-facing child or infant seats should NEVER be placed in front of an active passen...

Notice to owners of pickup trucks and utility type vehicles Utility vehicles have a significantly higher rollover rate thanother types of vehicles. Before you drive your vehicle, please read this Owner’s Guide carefully.Your vehicle is not a passenger car. As with other vehicles of this type,failure...

These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Air Bag-Front Air Bag-Side Child Seat Child Seat InstallationWarning Child Seat LowerAnchor Child Seat TetherAnchor Brake System Anti-Lock Brake System Brake Fluid -No...

WARNING LIGHTS AND CHIMES Standard instrument cluster Optional instrument cluster Warning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause expensive repairs. A warning light mayilluminate when a problem exists with one of your vehicle’s functions.Many lig...

Service engine soon: The Service engine soon indicator light illuminates when the ignition is firstturned to the ON position to checkthe bulb. Solid illumination after the engine is started indicates the OnBoard Diagnostics System (OBD-II) has detected a malfunction. Refer to On board diagnostics (O...

Anti-lock brake system: If the ABS light stays illuminated orcontinues to flash, a malfunction hasbeen detected, have the systemserviced immediately. Normalbraking is still functional unless the brake warning light also isilluminated. Air bag readiness: If this light fails to illuminate when ignitio...

Low tire warning (if equippedwith the Tire PressureMonitoring System): Illuminates when your tire pressure is low. Ifthe light remains on at start up orwhile driving, the tire pressure should be checked. Refer to Inspecting and Inflating Your Tires in the Tires, Wheels and Loading chapter. When the ...

Four wheel drive high (ifequipped): Illuminates when four-wheel drive high is engaged. Speed control: Illuminates when the speed control is activated. Turnsoff when the speed control systemis deactivated. Turn signal: Illuminates when the left or right turn signal or thehazard lights are turned on. ...

GAUGES Standard instrument cluster gauges Optional instrument cluster gauges Speedometer: Indicates the current vehicle speed. REVIEW COPY 2005 Explorer (exp) , Owners Guide (post-2002-fmt) (own2002) , Market: USA_English (fus) Instrument Cluster 15

Tachometer: Indicates the engine speed in revolutions per minute.Driving with your tachometerpointer continuously at the top ofthe scale may damage the engine. Battery voltage gauge: Indicates the battery voltage when theignition is in the ON position. If thepointer moves and stays outside thenormal...

AM/FM STEREO / SINGLE CD RADIO (IF EQUIPPED) 1. Balance: Press / to shift sound to the left/right speakers. 2. Fade: Press / to shift sound to the front/rear speakers. 3. SCN (Scan): Press to hear a brief sampling of all listenablestations or CD tracks. Press again tostop. 4. CLK: To set the hour, p...

To set the minute, press and hold CLK and press TUNE to decreaseor increase the minutes. 5. EJ (eject): Press to eject a CD. 6. COMP (Compression): In CD mode, press to bring louder andsofter levels into more comfortablelistening level. The compression icon (c) will appear in the display. 7. Shuffle...

14. CD : Press to enter CD mode or to play a CD already loaded into thesystem. 15. AM/FM: Press to choose a frequency band in radio mode. 16. Bass: Press / to increase/decrease the bass output. 17. Treble: Press / to increase/decrease the treble output. 18. CD slot: Insert a CD printed side up. CD u...

Traffic: Allows you to hear traffic broadcasts. With the feature ON, press SEEK or SCAN to find a station broadcasting a traffic report (if it isbroadcasting RDS data). Traffic information is not available in most U.S. markets . FIND Program type: Allows you to search RDS-equipped stations for a cer...

12. AM/FM: Press to select AM/FM frequency band. Autoset: Allows you to set the strongest local radio stations without losing your original manually setpreset stations for AM/FM1/FM2 . Press and momentarily hold AM/FM.AUTOSET will be shown. When the six strongest stations are filled, thestation stor...

CD: Press to start CD play. With the dual media audio, press CD totoggle between single CD and CDchanger play (if equipped). 7. Mute: Press to MUTE playing media; press again to return to theplaying media. 8. Auto: Press to set first six strongest stations (if available) intoAM, FM1 or FM2 memory bu...

12. Shuffle (CD): Press to play tracks in random order. Press againto disable. 13. Compression (CD): Press to bring soft and loud passagestogether for a more consistentlistening level. A small “c” willappear in the display to indicate that compression is enabled. Press againto disable. 14. Dolby 威 n...

Speed sensitive volume: Press MENU until SPEED VOL X appears in the display. Then press SEL to increase ( ) or decrease ( ) the volume setting. The level will appear in the display.Radio volume changes automatically and slightly with vehicle speed tocompensate for road and wind noise. Recommended le...

17. BAND: Press to toggle between AM/FM1/FM2 frequency band. 18. Memory presets: To set a station: Select frequency band; tuneto a station, press and hold a presetbutton until sound returns. 19. Power/volume: Press to turn ON/OFF; turn to increase ordecrease volume levels. 20. CD: Press to enter CD ...

Fade: Press FADE; then press SEL / to shift sound to the rear/front speakers. 10. SHUFFLE: Plays CD/MP3 tracks in random order when active(ON). Press to show shuffle status.Press again to toggle status. 11. TEXT/SEL: The filename, song title, artist or album text may beviewed while playing an MP3sel...

message display its corresponding text indicator (Fi, So, Ar, or AL) isshown in the elapsed time display. Press TEXT to scroll through the textfields. The display will scroll all of the text in the current field beforechanging to the next field. (TEXT must be pressed within 3 seconds ofthe previous ...

CAT: CAT is only available when equipped with Satellite Radio. Your Audiophile radio comes equipped with Satellite ready capability. The kitto enable Satellite reception is available through your dealer. DetailedSatellite instructions are included with the dealer installed kit. Dealer installed sate...

• Allow tapes which have been subjected to extreme heat, humidity orcold to reach a moderate temperature before playing. • Clean the cassette player head with a cassette cleaning cartridge after10–12 hours of play to maintain good sound/operation. Don’t: • Expose tapes to direct sunlight, extreme hu...

MANUAL HEATING AND AIR CONDITIONING SYSTEM(IF EQUIPPED) 1. Temperature selection: Controls the temperature of theairflow in the vehicle. 2. Air flow selections: Controls the direction of the airflow in thevehicle. See the following for a briefdescription on each control. MAX A/C: Uses recirculated a...

Dual Automatic Temperature Control (DATC) system (if equipped) 1. A/C control: Uses outside air to cool the vehicle. Press to turn on/offin all modes except or . 2. Recirculation control: Cools the vehicle more quickly byrecirculating the cabin air instead ofusing outside air and helps prevent unple...

Operating tips • To reduce fog build up on the windshield during humid weather, placethe air flow selector in the position. • To reduce humidity build up inside the vehicle, do not drive with theair flow selector in the OFF or with recirculated air engaged. • Do not put objects under the front seats...

Front auxiliary controls: 1. Temperature control: Determines temperature level. If the main climate control system is cooling in MAX A/C or mode, the auxiliary controls will not function as the entire vehicle will operate at afull cool temperature. 2. Mode selector: Press to select air flow directio...

1. Temperature control: Determines temperature levels. Ifthe main climate control system iscooling in MAX A/C or mode, the auxiliary controls will notfunction as the entire vehicle willoperate at a full cool temperature. 2. Mode selector: Press to select between air flow to (Floor) or (Panel). Direc...

HEADLAMP CONTROL Turns the lamps off. Turns on the parking lamps, instrument panel lamps, licenseplate lamps and tail lamps. Turns the headlamps on. Autolamp system(if equipped) The autolamp system sets theheadlamps to turn on and offautomatically. The autolamp control,located on the headlamp contro...

• the headlamp control is in the or position • the parking brake must be disengaged. Always remember to turn on your headlamps at dusk or duringinclement weather. The Daytime Running Light (DRL) System does not activate your tail lamps and generally may not provideadequate lighting during these cond...

• Rotate to full down position (past detent) to turn off the interiorlamps and will also disable the illuminated entry feature. AIMING THE HEADLAMPS The headlamps on your vehicle are properly aimed before leaving theassembly plant. If your vehicle is involved in an accident or if you haveproblems fi...

5. Locate the vertical adjuster foreach headlamp. Adjust the aim byturning the adjuster control eitherclockwise (to adjust down) orcounterclockwise (to adjust up). Note: Use a 4 mm socket or box wrench to turn the vertical adjustercontrol. 6. Horizontal aiming is not requiredfor this vehicle and isn...

Cargo/reading lamps The dome portion of the lamp orthe center light can be turned onwhen the headlamp control isrotated fully up or when a door isopened. With the ignition in the ACC or ON position, the rear dome lamp can beturned ON or OFF by sliding the control. BULBS Replacing exterior bulbs Chec...

Replacing headlamp bulbs Do not touch the glass of a halogen bulb. 1. Turn off the headlamps and openthe hood. 2. Pry up the two retainer pins untilthey stop to release the headlampassembly from the vehicle, then pullheadlamp forward. 3. Disconnect the electricalconnector by pushing the center taban...

Replacing front parking lamp/turn signal/sidemarker bulbs 1. Turn off the headlamp switch tooff. 2. Remove headlamp screw from thebulb assembly. 3. Disengage lamp assembly. 4. Rotate the bulb socketcounterclockwise and remove itfrom the lamp assembly. 5. Pull the bulb straight out of thesocket. Reve...

MULTI-FUNCTION LEVER Windshield wiper: Rotate the end of the control away from you toincrease the speed of the wipers;rotate towards you to decrease thespeed of the wipers. Speed dependent wipers: When the wiper control is on, the speed ofthe wipers will automatically adjustwith the vehicle speed. T...

Changing the wiper blades 1. Pull the wiper arm away from thevehicle. Turn the blade at an anglefrom the wiper arm. Push the lockpin manually to release the bladeand pull the wiper blade downtoward the windshield to remove itfrom the arm. 2. Attach the new wiper to thewiper arm and press it into pla...

A driver’s first responsibility is the safe operation of the vehicle.The most important thing you can do to prevent a crash is to avoid distractions and pay attention to the road. Wait until it is safe tooperate Mobile Communications Equipment. Rear center console features (if equipped) The rear cen...

Illuminated visor mirror (if equipped) Lift the mirror cover to turn on the visor mirror lamps. Type A Type B Slide on rod feature Rotate the visor towards the sidewindow and extend it rearward foradditional sunlight coverage. Note: To stow the visor back into the headliner, visor must beretracted b...

Do not plug electrical accessories into the cigarette lighter socket(if equipped). Always use the power point for accessories. Do not use the power point for operating the cigarette lighter element. The maximum power each power point can supply depends on the fuserating. For example: a 20A fuse shou...

One touch down Allows the driver’s window to openfully without holding the controldown. Press completely down onAUTO and release quickly. Pressagain to stop. Window lock The window lock feature allows onlythe driver to operate the powerwindows. To lock out all the window controlsexcept for the drive...

Turning off speed control There are two ways to turn off the speed control: • Depress the brake pedal. This will not erase your vehicle’s previouslyset speed. • Press the speed control OFFcontrol. Note: When you turn off the speed control or the ignition, your speedcontrol set speed memory is erased...

In AM, FM1, or FM2 mode: • Press MEM to select presetstations within the selected radioband. In Tape mode: • Press MEM to select the nextselection on the tape. In CD mode: • Press MEM to select the nextselection on the CD. In any mode: • Press VOL + or − to adjustvolume. Climate control features Pre...

Do not let children play with the moon roof or leave childrenunattended in the vehicle. They may seriously hurt themselves. HOMELINK 姞 WIRELESS CONTROL SYSTEM (IF EQUIPPED) The HomeLink 威 Wireless Control System, located on the overhead console, provides a convenient way to replace up to three hand-...

7. Press and release the “learn” or “smart” button. (The name and colorof the button may vary by manufacturer.) Note: There are 30 seconds in which to initiate Step eight. 8. Return to the vehicle and firmly press, hold for two seconds andrelease the HomeLink 威 button. Repeat the press/hold/release ...

Operating the HomeLink 姞 Wireless Control System To operate, simply press and releasethe appropriate HomeLink 威 button. Activation will now occur for thetrained product (garage door, gateoperator, security system, entrydoor lock, or home or office lightingetc.). For convenience, thehand-held transmi...

ELECTRONIC COMPASS/TEMPERATURE DISPLAY (IF EQUIPPED) OUTSIDE AIR TEMPERATURE The outside temperature display iscontained in the instrument clusterand displays all the time. Ifequipped with the DEATC climatecontrol system, the outsidetemperature will be displayed there.For more information, refer to ...

Compass zone adjustment 1. Determine which magnetic zoneyou are in for your geographiclocation by referring to the zonemap. 2. Turn ignition to the ON position. 3. Locate compass sensor mountedat base of mirror. 4. Press the button on the top ofthe compass module until ZONEappears in the instrument ...

3. Press the button on the top ofthe compass module until ZONEappears in the instrument clusterdisplay. Continue to hold down untilZONE disappears and CAL isdisplayed (approximately eightseconds) and release. 4. Drive the vehicle slowly (less than 5 km/h [3 mph]) in circles untilCAL indicator turns ...

System warnings System warnings alert you to possible problems or malfunctions in yourvehicle’s operating systems. In the event of a multiple warning situation, the message center willcycle the display to show all warnings by displaying each one for severalseconds. The message center will display th...

CHECK ADVANCETRAC 娂 (if equipped). Displayed when the AdvanceTrac 娂 system is not operating properly. If this message is displayed on the message center the AdvanceTrac 娂 system will be partially operable. If this warning stays on while the engine is running,contact your dealer for service as soon a...

To reset the oil monitoring system to 100% after each oil change[approximately 5,000 miles (8,000 km) or 180 days] perform thefollowing: 1. Press and release the SETUPcontrol to display “PRESS RESETAT OIL CHANGE”. 2. Press and release the RESETcontrol to display “HOLD RESETTO CONFIRM”. 3. Press and ...

KEYS One key operates all the locks and starts the vehicle. Always carry aspare key with you in case of an emergency. Your keys are programmed to your vehicle; using a non-programmed keywill not permit your vehicle to start. If you lose your dealer suppliedkeys, replacement keys are available throug...

Childproof door locks • When these locks are set, therear doors cannot be opened fromthe inside. • The rear doors can be openedfrom the outside when the doorsare unlocked. The childproof locks are located onrear edge of each rear door andmust be set separately for eachdoor. Setting the lock for one ...

2. Press and release again within three seconds to confirm that all the doors are closed and locked. Note: The doors will lock again, the horn will chirp and the lamps flash once. Note: If any door, the liftgate or the liftgate glass are not closed properly, the horn will make two quick chirps. Open...

Deactivating the memory seat feature To deactivate this feature: 1. Press the SET control on the driver’s door panel. 2. Within 5 five seconds, press any control on the remote transmitterwhich you would like to deactivate and then press the SET control onthe driver’s door panel. 3. Repeat this proce...

Note: Replacement of the battery will not cause the remote transmitter to become deprogrammed from your vehicle. The remote transmittershould operate normally after battery replacement. Replacing lost remote entry transmitters If you would like to have your remote entry transmitter reprogrammedbecau...

To unlock all doors and liftgate, press the 3 • 4 control within five seconds. To open the liftgate window, press the 5 • 6 control within five seconds. To lock all doors, liftgate and liftgate window, press the 7 • 8 and the 9 • 0 at the same time. Note: The driver’s door must be closed. You do not...

Power door unlock/lock procedure You must complete steps 1-5 within30 seconds or the procedure willhave to be repeated. If theprocedure needs to be repeated,you must wait 30 seconds. 1. Turn the ignition to the 3 (ON)position. 2. Press the power door unlockcontrol three times. 3. Turn the ignition f...

SECURILOCK 姟 PASSIVE ANTI-THEFT SYSTEM SecuriLock 娂 passive anti-theft system is an engine immobilization system. This system is designed to help prevent the engine from beingstarted unless a coded key programmed to your vehicle is used. The use of the wrong type of coded key may lead to a “no-start...

Automatic arming The vehicle is armed immediatelyafter switching the ignition to the 2(ACCESSORY) position. The theft indicator will flash everytwo seconds when the vehicle isarmed. Automatic disarming Switching the ignition to the 3 (ON) position with a coded key disarms the vehicle. • The theft in...

Please read and understand theentire procedure before you begin. 1. Insert the first previouslyprogrammed coded key into the ignition. 2. Turn the ignition from the 1 (OFF/LOCK) position to the 3 (ON)position. Keep the ignition in the 3 (ON) position for at least threeseconds, but no more than 10 se...

SEATING Notes: Reclining the seatback can cause an occupant to slide under theseat’s safety belt, resulting in severe personal injuries in the event of a collision. Do not pile cargo higher than the seatbacks to reduce the risk ofinjury in a collision or sudden stop. Adjustable head restraints Head ...

Push control to lower head restraint. Adjusting the front manual seat (if equipped) Never adjust the driver’s seat or seatback when the vehicle ismoving. Always drive and ride with your seatback upright and the lapbelt snug and low across the hips. Lift handle to move seat forward orbackward. Pull l...

Press front to raise or lower thefront portion of the seat cushion. Press rear to raise or lower the rearportion of the seat cushion. Press the control to move the seatforward, backward, up or down. Memory seat/adjustable pedals/easy entry-exit feature (if equipped) This system allows automaticposit...

A position can only be set or recalled when the transmission gearshift isin P (Park) or N (Neutral). A memory seat position may be programmedat any time. The memory seat positions are also recalled when you press your remoteentry transmitter UNLOCK control. The third position is recalled when both b...

Heated seats (if equipped) To operate the heated seats: • Push control located on the seatto activate. • Push again to deactivate. The heated seat icon in the Dual Automatic Temperature Control(DATC) will illuminate when activated. REAR SEATSFolding down the 60/40 rear seats (if equipped) If the rea...

To return the seat to a seatingposition: 1. Push the seat down and latch tothe floor with a moderate amount ofeffort and speed. 2. Make sure the seat is latched tothe floor. 3. Push the handle forward justenough so that the seat back isreleased. 4. Bring the seat back to an upright position. The sea...

2. Pull the seat release lever locatedon top of the seatback while liftingthe seatback into the uprightposition. 3. The seatback will latch into place. The third row seat is equipped with combination lap and shoulder beltsin both seating positions. For information on the proper operation of thesafet...

If any of these things happen, even intermittently, have the PersonalSafety System serviced at your dealership or by a qualified technicianimmediately. Unless serviced, the system may not function properly inthe event of a collision. Safety restraints precautions Always drive and ride with your seat...

Always transport children 12 years old and under in the backseat and always properly use appropriate child restraints. Safety belts and seats can become hot in a vehicle that has beenclosed up in sunny weather; they could burn a small child. Check seat covers and buckles before you place a child any...

• Front and rear seats All safety restraints in the vehicle are combination lap and shoulderbelts. All of the passenger combination lap and shoulder belts have twotypes of locking modes described below: Vehicle sensitive mode This is the normal retractor mode, which allows free shoulder belt lengtha...

After any vehicle collision, the combination lap and shoulder beltsystem at all passenger seating positions must be checked by a qualified technician to verify that the “automatic locking retractor”feature for child seats is still functioning properly, in addition to otherchecks for proper seat belt...

Conditions of operation If... Then... The driver’s safety belt is notbuckled before the ignition switchis turned to the ON position... The safety belt warning lightilluminates 1-2 minutes and thewarning chime sounds 4-8seconds. The driver’s safety belt is buckledwhile the indicator light isilluminat...

The following are reasons most often given for not wearing safety belts(All statistics based on U.S. data): Reasons given... Consider... “Crashes are rare events” 36700 crashes occur every day. The more we drive, the more we areexposed to “rare” events, even forgood drivers. 1 in 4 of us will be ser...

Reasons given... Consider... “I have an air bag” Air bags offer greater protection whenused with safety belts. Frontal airbagsare not designed to inflate in rear andside crashes or rollovers. “I’d rather be thrown clear” Not a good idea. People who are ejected are 40 times more likelyto DIE. Safety ...

1. Turn the ignition switch to the RUN (or ON) position. (DO NOTSTART THE ENGINE) 2. Wait until the safety belt warning light turns off. (Approximately 1–2minutes) • Steps 3–5 must be completed within 60 seconds or the procedure willhave to be repeated. 3. Buckle then unbuckle the safety belt three ...

a collision be replaced. However, if the collision was minor and aqualified technician finds that the belts do not show damage andcontinue to operate properly, they do not need to be replaced. Safetybelt assemblies not in use during a collision should also be inspected andreplaced if either damage o...

Children and air bags Children must always be properlyrestrained. Accident statisticssuggest that children are safer whenproperly restrained in the rearseating positions than in the frontseating position. Failure to followthese instructions may increase therisk of injury in a collision. Air bags can...

The air bags inflate and deflaterapidly upon activation. After air bagdeployment, it is normal to notice asmoke-like, powdery residue orsmell the burnt propellant. This mayconsist of cornstarch, talcumpowder (to lubricate the bag) orsodium compounds (e.g., bakingsoda) that result from thecombustion ...

• diagnostic module. • and the electrical wiring which connects the components. The diagnostic module monitors its own internal circuits and thesupplemental air bag electrical system wiring (including the impactsensors), the system wiring, the air bag system readiness light, the airbag back up power...

Safety Canopy 姟 system (if equipped) Do not place objects ormount equipment on or near the headliner at the siderailthat may come into contact with adeploying Safety Canopy 娂 . Failure to follow these instructions mayincrease the risk of personal injuryin the event of a collision. Do not lean your h...

How does the Safety Canopy 姟 system work? The design and development of theSafety Canopy 娂 system included recommended testing proceduresthat were developed by a group ofautomotive safety experts known asthe Side Airbag Technical WorkingGroup. These recommended testingprocedures help reduce the risk...

Any difficulty with the system is indicated by one or more of thefollowing: • The readiness light (same light as for front air bag system) will eitherflash or stay lit. • The readiness light will not illuminate immediately after ignition isturned on. • A series of five beeps will be heard. The tone ...

Booster seats should be used until you can answer YES to ALL of thesequestions: • Can the child sit all the way backagainst the vehicle seat back withknees bent comfortably at theedge of the seat withoutslouching? • Does the lap belt rest low across the hips? • Is the shoulder belt centered on the s...

The shoulder belt should cross the chest, resting snugly on the center ofthe shoulder. The lap belt should rest low and snug across the hips,never up high across the stomach. If the booster seat slides on the vehicle seat, placing a rubberized meshsold as shelf or carpet liner under the booster seat...

Rear-facing child seats or infant carriers should never be placedin the front seats. Installing child safety seats with combination lap and shoulderbelts Air bags can kill or injure a child in a child seat. NEVER place a rear-facing child seat in front of an active air bag. If you must use a forward...

7. Pull the lap belt portion acrossthe child seat toward the buckle andpull up on the shoulder belt whilepushing down with your knee on thechild seat. 8. Allow the safety belt to retract toremove any slack in the belt. 9. Before placing the child in theseat, forcibly move the seat forwardand back to...

NOTICE TO UTILITY VEHICLE AND TRUCK OWNERS Utility vehicles and trucks handledifferently than passenger cars inthe various driving conditions thatare encountered on streets,highways and off-road. Utilityvehicles and trucks are not designedfor cornering at speeds as high aspassenger cars any more tha...

Power is supplied to all four wheelsthrough a transfer case or powertransfer unit. 4WD vehicles allowyou to select different drive modesas necessary. Information on shiftingprocedures and maintenance can befound in your Owner’s Guide . You should become thoroughly familiarwith this information befor...

Under-inflation is the most common cause of tire failures andmay result in severe tire cracking, tread separation or ⬙ blowout ⬙ , with unexpected loss of vehicle control and increased risk of injury.Under-inflation increases sidewall flexing and rolling resistance,resulting in heat buildup and inte...

when you get to the pump. It is normal for tires to heat up and the airpressure inside to go up as you drive. Never “bleed” or reduce airpressure when tires are hot.2. Remove the cap from the valve on one tire, then firmly press the tiregauge onto the valve and measure the pressure.3. Add enough air...

The installation of replacement tires with steel cord body plies in the tiresidewall may cause malfunction of the Tire Pressure Monitoring System(TPMS), and is not recommended (cord material information is moldedon the tire sidewall). Additionally, if your vehicle was originally equippedwith run-fla...

Tool Location Spare tire Under the vehicle, just in front ofthe rear bumper. The spare tirewinch drive nut is located at therear center of the cargo areaunder a lid. Jack, lug nut wrench, jack handle, wheel chock Behind the rear seat under thecarpeted floor lid in the cargofloor. The tools are locat...

Removing the spare tire Do not use an impact wrench on the winch drive nut. This willdamage the spare tire winch. 1. Open the cover from the carpeting on cargo floor to expose the winchdrive nut. 2. Insert the lug wrench on thewinch drive nut. The wrench will stop moving andforward resistance to tur...

To lessen the risk ofpersonal injury, do not put any part of your body under thevehicle while changing a tire. Donot start the engine when yourvehicle is on the jack. The jack isonly meant for changing the tire. • Never use the front or reardifferential as a jacking point. 5. Remove the lug nuts wit...

increases significantly and the spare tire carrier ratchets or slips whenthe tire is raised to the maximum tightness. Tighten to the best of yourability, to the point where the ratchet/slip occurs, if possible. The sparetire carrier will not allow you to overtighten. If the spare tire carrierratchet...

When a wheel is installed, always remove any corrosion, dirt andforeign materials present on the mounting surfaces of the wheel and the surface of the front disc brake hub and rotor that contacts thewheel. Installing wheels without correct metal-to-metal contact at thewheel mounting surfaces can cau...

4. R: Indicates a “radial” type tire. 5. 15: Indicates the wheel or rim diameter in inches. If you change your wheel size, you will have to purchase new tires to match the new wheeldiameter. 6. 95: Indicates the tire’s load index. It is an index that relates to how much weight a tire can carry. You ...

13. Maximum Permissible Inflation Pressure: Indicates the tire manufacturers’ maximum permissible pressure and/or the pressure atwhich the maximum load can be carried by the tire. This pressure isnormally higher than the manufacturer’s recommended cold inflationpressure which can be found on either ...

Information on “T” type tires “T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below: T145/80D16 is an example of a tiresize. Note: The temporary tire size for your vehicle may be different fromthis example. 1. T: Indicates a type of tire, ...

Safety practices Driving habits have a great deal to do with your tire mileage and safety. • Observe posted speed limits • Avoid fast starts, stops and turns • Avoid potholes and objects on the road • Do not run over curbs or hit the tire against a curb when parking If your vehicle is stuck in snow,...

Wheel misalignment in the front or the rear can cause uneven and rapidtreadwear of your tires and should be corrected by a qualified technicianat a Ford or Lincoln/Mercury dealer. Front wheel drive (FWD) vehiclesand those with an independent rear suspension (if equipped) mayrequire alignment of all ...

The tire pressure should be checked periodically (at least monthly) usingan accurate tire gauge, refer to Inspecting and inflating your tires in this chapter. Understanding your Tire Pressure Monitoring System (TPMS) The Tire Pressure Monitoring System measures pressure in your fourroad tires and se...

Low Tire WarningLight Customer Action Required Solid Warning Light 1. Check your tire pressure to ensure they areproperly inflated, refer to Inspecting and inflating your tires in this chapter. Ford recommends the use of a digital or dial typetire pressure gauge rather than a stick typetire pressure...

The Tire Pressure Monitoring System complies with part 15 of the FCCrules and with RS-210 of Industry Canada. Operation is subject to thefollowing two conditions: (1) This device may not cause harmfulinterference, and (2) This device must accept any interference received,including interference that ...

VEHICLE LOADING – WITH AND WITHOUT A TRAILER This section will guide you in the proper loading of your vehicle and/ortrailer, to keep your loaded vehicle weight within its design ratingcapability, with or without a trailer. Properly loading your vehicle willprovide maximum return of vehicle design p...

Cargo Weight – includes all weight added to the Base Curb Weight, including cargo and optional equipment. When towing, trailer tongue loador king pin weight is also part of cargo weight. GAW (Gross Axle Weight) – is the total weight placed on each axle (front and rear) – including vehicle curb weigh...

GVW (Gross Vehicle Weight) – is the Vehicle Curb Weight + cargo + passengers. GVWR (Gross Vehicle WeightRating) – is the maximum allowable weight of the fully loadedvehicle (including all options,equipment, passengers and cargo). The GVWR is shown on theSafety Compliance CertificationLabel located o...

Exceeding any vehicle weight rating limitation could result inserious damage to the vehicle and/or personal injury. Steps for determining the correct load limit: 1. Locate the statement “The combined weight of occupants and cargoshould never exceed XXX pounds” on your vehicle’s placard. 2. Determine...

pounds, the calculation would be: 1400 – (2 x 220) – (12 x 100) =1400 – 440 – 1200 = – 40 pounds; no, you do not have enough cargocapacity to carry that much weight. You will need to reduce the loadweight by at least 240 pounds. If you remove 3-100 pound cementbags, then the load calculation would b...

Follow these guidelines to ensure safe towing procedure: • Stay within your vehicle’s load limits. • Thoroughly prepare your vehicle for towing. Refer to Preparing to tow in this chapter. • Use extra caution when driving while trailer towing. Refer to Driving while you tow in this chapter. • Service...

4x4/AWD Notes: - For high altitude operation, reduce GCW by 2% per 1,000 ft. (300 meters) elevation. For definitions of terms used in this table andinstructions on how to calculate your vehicle load, refer to Vehicle loading in this chapter. Maximum trailer weights shown. The combined weight of the ...

Do not connect a trailer’s hydraulic brake system directly to yourvehicle’s brake system. Your vehicle may not have enough braking power and your chances of having a collision greatly increase. The braking system of the tow vehicle is rated for operation at theGVWR not GCWR. Trailer lamps Trailer la...

Trailer towing tips • Practice turning, stopping and backing up before starting on a trip toget the feel of the vehicle trailer combination. When turning, makewider turns so the trailer wheels will clear curbs and other obstacles. • Allow more distance for stopping with a trailer attached. • If you ...

STARTING Positions of the ignition 1. OFF/LOCK, shuts off the engineand all accessories/locks the steeringwheel, gearshift lever and allows keyremoval. 2. ACC, allows the electricalaccessories such as the radio tooperate while the engine is notrunning. This position also unlocksthe steering wheel. 3...

Starting the engine 1. Turn the key to 3 (ON) withoutturning the key to 4 (START). Ifthere is difficulty in turning the key,rotate the steering wheel until thekey turns freely. This condition mayoccur when: • the front wheels are turned • a front wheel is against the curb 2. Turn the key to 4 (START...

Refer to Brake system warning light in the Instrument Cluster chapter for information on the brakesystem warning light. Four-wheel anti-lock brake system (ABS) Your vehicle is equipped with an Anti-lock Braking System (ABS). Thissystem helps you maintain steering control during emergency stops bykee...

Parking brake Apply the parking brake wheneverthe vehicle is parked. To set theparking brake, press the parkingbrake pedal down until the pedalstops. The BRAKE warning lamp in theinstrument cluster illuminates andremains illuminated (when theignition is turned ON) until theparking brake is released....

Driving conditions which may activate AdvanceTrac 娂 include: • Taking a turn too fast. • Maneuvering quickly to avoid an accident, pedestrian or obstacle. • Hitting a patch of ice. • Changing lanes on a snow-rutted road. • Entering a snow-free road from a snow-covered side street, or viceversa. • En...

If a failure is detected in the AdvanceTrac 娂 /Roll Stability Control system, the warning indicator light in the instrument cluster will stay on.If the warning indicator light in the instrument cluster remains on whilethe engine is running, have the system serviced immediately. Pressing the control ...

Vehicles with a higher center of gravity such as utility andfour-wheel drive vehicles handle differently than vehicles with a lower center of gravity. Utility and four-wheel drive vehicles are not designed for cornering at speeds as high as passenger cars any morethan low-slung sports cars are desig...

2. Locate the access plug to thebrake-shift interlock override. It islocated on the underside of thesteering column. 3. Remove the access plug with aflat head screwdriver (or similartool). 4. Insert a tool (or screwdriver) into the access hole to override thebrake-shift interlock. Apply the brake an...

• To return to O/D (overdrive mode), press the transmission controlswitch. The O/D OFF lamp will not be illuminated. • O/D (Overdrive) is automatically returned each time the key is turnedoff. 3 (Third) Transmission operates in third gear only. Used for improved traction on slippery roads. Selecting...

REVERSE SENSING SYSTEM (IF EQUIPPED) The Reverse Sensing System (RSS) sounds a tone to warn the driver ofobstacles near the rear bumper when the R (Reverse) is selected and thevehicle is moving at speeds less than 3 mph (5 km/h). The system is noteffective at speeds above 3 mph (5 km/h) and may not ...

LIMITED-SLIP AXLE (IF EQUIPPED) This axle provides added traction on slippery surfaces, particularly whenone wheel is on a poor traction surface. Under normal conditions, thelimited slip axle functions like a standard rear axle. Extended use of other than the manufacturer’s specified size tires on a...

Using the Control Trac 4WD system 4X4 AUTO - Power to all four wheels; used for normal street and highway driving. 4X4 HIGH (4WD High) - Used for extra traction such as in snow or icy roads or in off-road situations. Not intended for use on dry pavement. 4X4 LOW (4WD Low) - Uses extra gearing to pro...

4. Press the desired 4WD position. • If shifting into 4X4 LOW (4WD Low), wait for the 4X4 LOW light inthe instrument cluster to turn on indicating the shift is complete. • If shifting out of 4X4 LOW (4WD Low), wait for the 4X4 LOW light inthe instrument cluster to turn off indicating the shift is co...

If your vehicle goes off the edge of the pavement • If your vehicle goes off the edge of the pavement, slow down, butavoid severe brake application, ease the vehicle back onto thepavement only after reducing your speed. Do not turn the steeringwheel too sharply while returning to the road surface. •...

turn the steering wheel only as rapidly and as far as required to avoidthe emergency. Excessive steering will result in less vehicle control,not more. Additionally, smooth variations of the accelerator and/orbrake pedal pressure should be utilized if changes in vehicle speed arecalled for. Avoid abr...

Mud and water If you must drive through highwater, drive slowly. Traction orbrake capability may be limited. When driving through water,determine the depth; avoid waterhigher than the bottom of the hubs(if possible) and proceed slowly. Ifthe ignition system gets wet, the vehicle may stall. Once thro...

possibly rolling over. Whenever driving on a hill, determine beforehandthe route you will use. Do not drive over the crest of a hill withoutseeing what conditions are on the other side. Do not drive in reverseover a hill without the aid of an observer. When climbing a steep slope or hill,start in a ...

ALL WHEEL DRIVE (AWD) SYSTEM (IF EQUIPPED) Your vehicle may be equipped with a full-time All Wheel Drive (AWD)transfer case. With the AWD option, power is supplied to all four wheelsall the time with no need to shift between two-wheel drive andfour-wheel drive. For the lubricant specification and re...

brake steadily. Do not “pump” the brakes. Refer to the Brakes section of this chapter for additional information on the operation of the anti-lockbrake system. Never drive with chains on the front tires of AWD vehicles without alsoputting them on the rear tires. This could cause the rear to slide an...

GETTING ROADSIDE ASSISTANCE To fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program. Thisprogram is separate from the New Vehicle Limited Warranty. The serviceis available: • 24–hours, seven days a week • for the New Vehicle Limited...

Canadian customers who require roadside assistance, call1–800–665–2006. If you need to arrange roadside assistance for yourself, Ford MotorCompany will reimburse a reasonable amount. To obtain reimbursementinformation, U.S. Ford or Mercury vehicles customers call1-800-241-3673; Lincoln vehicle custo...

The fuel pump shut-off switch islocated in the passenger’s foot well,by the kick panel. Use the following procedure to reset the fuel pump shut-off switch. 1. Turn the ignition to the OFF position. 2. Check the fuel system for leaks. 3. If no fuel leak is apparent, reset the fuel pump shut-off switc...

Note: Always replace a fuse with one that has the specified amperage rating. Using a fuse with a higher amperage rating can cause severe wiredamage and could start a fire. Standard fuse amperage rating and color COLOR Fuse rating Mini fuses Standard fuses Maxi fuses Cartridge maxi fuses 2A Grey Grey...

Passenger compartment fuse panel The fuse panel is located below theinstrument panel on the driver’sside. To remove a fuse use the fuse puller tool provided on the fuse panel box. 1 6 16 21 26 27 28 29 30 22 23 24 25 17 18 19 20 7 8 9 10 11 12 13 14 15 2 3 4 5 REVIEW COPY 2005 Explorer (exp) , Owner...

Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 23 15A Not used 24 15A Cigar lighter, OBD II, Neutral tow 25 5A Mode-Temperature actuator forauxiliary climate control, Trailertow battery charge relay coil,TPMS 26 7.5A Reverse park aid, Brake shiftinterlock, IVD switc...

Passenger compartment fuse panel (top side) These relays are located on the reverse side of the passengercompartment fuse panel. See your dealer or a certified technician forservice of this relay box. Fuse/Relay Location Description Relay 1 Flasher Relay 2 Rear defrost Relay 3 Delayed accessory Rela...

Power distribution box The power distribution box islocated in the engine compartment.The power distribution box containshigh-current fuses that protect yourvehicle’s main electrical systemsfrom overloads. Always disconnect the battery before servicing high currentfuses. To reduce risk of electrical...

Auxiliary relay box (Vehicles equipped with 4x4) The relay box is located on the frontright fender well. The relays are coded as follows: Fuse/Relay Location Description Relay 64 Two-speed 4x4 motor clockwise Relay 65 Two-speed 4x4 motor counterclockwise Relay 66 Open JUMP STARTING YOUR VEHICLE The ...

Preparing your vehicle When the battery is disconnected or a new battery is installed, thetransmission must relearn its shift strategy. As a result, the transmissionmay have firm and/or soft shifts. This operation is considered normal andwill not affect function or durability of the transmission. Ov...

4. Make the final connection of the negative (-) cable to an exposedmetal part of the stalled vehicle’s engine, away from the battery and thecarburetor/fuel injection system. Do not use fuel lines, engine rocker covers or the intake manifold as grounding points. Do not connect the end of the second ...

Removing the jumper cables Remove the jumper cables in the reverse order that they wereconnected. 1. Remove the jumper cable from the ground metal surface. 2. Remove the jumper cable on the negative (-) connection of thebooster vehicle’s battery. 3. Remove the jumper cable from the positive (+) term...

4. Remove the jumper cable from the positive (+) terminal of thedisabled vehicle’s battery. After the disabled vehicle has been started and the jumper cablesremoved, allow it to idle for several minutes so the engine computer canrelearn its idle conditions. WRECKER TOWING + – + – REVIEW COPY 2005 Ex...

GETTING THE SERVICES YOU NEED At home You must take your Ford vehicle to an authorized Ford dealer forwarranty repairs. While any Ford dealership handling your vehicle linewill provide warranty service, we recommend you return to your sellingdealer who wants to ensure your continued satisfaction. Pl...

In the United States, a warranty dispute must be submitted to theDispute Settlement Board before taking action under the Magnuson-MossWarranty Act, or to the extent allowed by state law, before pursuingreplacement or repurchase remedies provided by certain state laws. Thisdispute handling procedure ...

• available free to owners and lessees of qualifying Ford Motor Companyvehicles. The Dispute Settlement Board may not be available in all states. FordMotor Company reserves the right to change eligibility limitations, modifyprocedures and/or to discontinue this service without notice and withoutincu...

Oral presentations If you would like to make an oral presentation, indicate YES to question6 on the application. While it is your right to make an oral presentationbefore the Board, this is not a requirement and the Board will decide thecase whether or not an oral presentation is made. An oral prese...

UTILIZING THE MEDIATION/ARBITRATION PROGRAM(CANADA ONLY) In those cases where you continue to feel that the efforts by Ford andthe dealer to resolve a factory-related vehicle service concern have beenunsatisfactory, Ford of Canada participates in an impartial third partymediation/arbitration program...

If you did not take advantage of the Ford Extended Service Plan at thetime of purchasing your vehicle, you may still be eligible. Since thisinformation is subject to change, please ask your dealer for completedetails about Ford Extended Service Plan coverage options, or visit theFord ESP website at ...

WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutralPh shampoo, such as Motorcraft Detail Wash (ZC-3–A), which is availablefrom your dealer. • Never use strong household detergents or soap, such as dish washingor laundry liquid. These products can discolor and s...

PAINT CHIPS Your dealer has touch-up paint and sprays to match your vehicle’s color.Take your color code (printed on a sticker in the driver’s door jam) toyour dealer to ensure you get the correct color. • Remove particles such as bird droppings, tree sap, insect deposits, tarspots, road salt and in...

• For routine cleaning, use Motorcraft Detail Wash (ZC-3–A). • If tar or grease spots are present, use Motorcraft Bug and TarRemover (ZC-42). WINDOWS AND WIPER BLADES The windshield, rear and side windows and the wiper blades should becleaned regularly. If the wipers do not wipe properly, substances...

• Do not use household or glass cleaners as these may damage thefinish. INTERIOR For fabric, carpets, cloth seats and safety belts: • Remove dust and loose dirt with a vacuum cleaner. • Remove light stains and soil with Motorcraft Extra StrengthUpholstery Cleaner (ZC-41). • If grease or tar is prese...

FORD, LINCOLN AND MERCURY CAR CARE PRODUCTS Your Ford, Lincoln or Mercury dealer has many quality products availableto clean your vehicle and protect its finishes. These quality productshave been specifically engineered to fulfill your automotive needs; theyare custom designed to complement the styl...

SERVICE RECOMMENDATIONS • Use the Scheduled Maintenance Guide to track routine service. • Use only recommended fuels, lubricants, fluids and service partsconforming to specifications. • Your dealership can provide parts and service. PRECAUTIONS WHEN SERVICING YOUR VEHICLE • Do not work on a hot engi...

OPENING THE HOOD 1. Inside the vehicle, pull the hoodrelease handle located under thebottom left corner of the instrumentpanel. 2. Go to the front of the vehicle and release the auxiliary latch that islocated under the front center of the hood. 3. Lift the hood. REVIEW COPY 2005 Explorer (exp) , Own...

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 4.0L SOHC V6 engine 1. Engine coolant reservoir 2. Engine oil filler cap 3. Power steering fluid reservoir 4. Brake fluid reservoir 5. Power distribution box 6. Battery 7. Engine oil dipstick 8. Air filter assembly 9. Windshield washer fluid reservoir...

WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely. Only use a washer fluid that meets Ford specification WSB-M8B16–A2.Refer to Lubricant specifications in the Capacities and specifications chapter. State or local reg...

ENGINE OIL Checking the engine oil Refer to the scheduled maintenance guide for the appropriate intervalsfor checking the engine oil. 1. Make sure the vehicle is on level ground. 2. Turn the engine off and wait a few minutes for the oil to drain into theoil pan. 3. Set the parking brake and ensure t...

• 4.6L V8 engine 6. Wipe the indicator clean. Insert the indicator fully, then remove itagain. • If the oil level is between the MIN and MAX marks, the oil level is acceptable, DO NOT ADD OIL. • If the oil level is below the MIN mark, add enough oil to raise the levelwithin the MIN-MAX range . • 4.0...

• 4.6L V8 engine • Oil levels above the MAX mark may cause engine damage. Some oilmust be removed from the engine by a service technician. 7. Put the indicator back in and ensure it is fully seated. Adding engine oil 1. Check the engine oil. For instructions, refer to Checking the engine oil in this...

BATTERY Your vehicle is equipped with aMotorcraft maintenance-free batterywhich normally does not requireadditional water during its life ofservice. However, for severe usage or in high temperature climates, check thebattery electrolyte level. Refer to the Scheduled Maintenance Guide for the service...

When lifting a plastic-cased battery, excessive pressure on theend walls could cause acid to flow through the vent caps, resulting in personal injury and/or damage to the vehicle or battery.Lift the battery with a battery carrier or with your hands on oppositecorners. Keep batteries out of reach of ...

If the battery has been disconnected or a new battery has been installed,the clock and the preset radio stations must be reset once the battery isreconnected. • Always dispose of automotivebatteries in a responsible manner.Follow your local authorizedstandards for disposal. Call yourlocal authorized...

When the engine is cold, check thelevel of the engine coolant in thereservoir. • The engine coolant should be at the “FULL COLD” level or within the“COLD FILL RANGE” as listed on the engine coolant reservoir(depending upon application). • Refer to the Scheduled Maintenance Guide for service interval...

Do not add engine coolant when the engine is hot. Steam andscalding liquids released from a hot cooling system can burn you badly. Also, you can be burned if you spill coolant on hot engine parts. Do not put engine coolant in the windshield washer fluidcontainer. If sprayed on the windshield, engine...

remove the coolant pressure relief cap on the radiator of a vehicle withan overflow system, follow these steps to add engine coolant. To reduce the risk of personal injury, make sure the engine iscool before unscrewing the coolant pressure relief cap. The cooling system is under pressure; steam and ...

Used engine coolant should be disposed of in an appropriate manner. Follow your community’s regulations and standards for recyclingand disposing of automotive fluids. Coolant refill capacity To find out how much fluid your vehicle’s cooling system can hold, referto Refill capacities in this section....

2. Arrange for the vehicle to be taken to a service facility. 3. If this is not possible, wait a short period for the engine to cool. 4. Check the coolant level and replenish if low. Never remove the coolant reservoir cap while the engine isrunning or hot. 5. Restart the engine and take your vehicle...

Observe the following guidelines when handling automotive fuel: • Extinguish all smoking materialsand any open flames beforefueling your vehicle. • Always turn off the vehicle beforefueling. • Automotive fuels can be harmfulor fatal if swallowed. Fuels such as gasoline and ethanol are highlytoxic an...

U.S. government regulations require fuel ethanol dispensingpumps to have a small, square, orange and black label with thecommon abbreviation or the appropriate percentage for thatregion. Use of other fuels such as Fuel Methanol may causepowertrain damage, a loss of vehicle performance, and yourwarra...

Cleaner air Ford endorses the use of reformulated “cleaner-burning” gasolines toimprove air quality. Running out of fuel Avoid running out of fuel because this situation may have an adverseaffect on powertrain components. If you have run out of fuel: • You may need to cycle the ignition from OFF to ...

For consistent results when filling the fuel tank: • Turn the engine/ignition switch to the off position prior to refueling,an error in the reading will result if the engine is left running. • Use the same filling rate setting (low — medium — high) each timethe tank is filled. • Allow no more than 2...

Keep a record for at least one month and record the type of driving (cityor highway). This will provide an accurate estimate of the vehicle’s fueleconomy under current driving conditions. Additionally, keeping recordsduring summer and winter will show how temperature impacts fueleconomy. In general,...

• Perform all regularly scheduled maintenance items. Follow therecommended maintenance schedule and owner maintenance checksfound in your vehicle scheduled maintenance guide. Conditions • Heavily loading a vehicle or towing a trailer may reduce fuel economyat any speed. • Carrying unnecessary weight...

EMISSION CONTROL SYSTEM Your vehicle is equipped with various emission control components and acatalytic converter which will enable your vehicle to comply with applicableexhaust emission standards. To make sure that the catalytic converter andother emission control components continue to work prope...

CHECKING AND ADDING POWER STEERING FLUID Check the power steering fluid. Refer to the scheduled maintenanceguide for the service interval schedules. If adding fluid is necessary, useonly MERCON 威 ATF. • 4.0L SOHC V6 engine • 4.6L V8 engine 1. Start the engine and let it run until it reaches normal o...

BRAKE FLUID RESERVOIR The fluid level will drop slowly asthe brakes wear, and will rise whenthe brake components are replaced.Fluid levels below the “MAX” linethat do not trigger the brake systemwarning lamp are within the normaloperating range, there is no need toadd fluid. If the fluid levels areo...

3. Remove the air filter element from the air filter housing. 4. Wipe the air filter housing and cover clean to remove any dirt ordebris and to ensure good sealing. 5. Install a new air filter element. Be careful not to crimp the filterelement edges between the air filter housing and cover. This cou...

3. Add only enough fluid throughthe filler opening so that the fluidlevel is at the bottom of theopening. Use only fluid that meets Ford specifications. Refer to Lubricant specifications in this chapter. DRIVELINE UNIVERSAL JOINT AND SLIP YOKE Your vehicle may be equipped with universal joints that ...

2 For spark plug replacement, see your dealer or a qualified service technician. Refer to the Scheduled Maintenance Guide for the appropriate intervals for changing the spark plugs. Replace the spark plugs with ones that meet Ford material anddesign specifications for your vehicle, such as Motorcraf...

1 Ensure the correct automatic transmission fluid is used. MERCON 威 and MERCON 威 V are not interchangeable. DO NOT mix MERCON 威 and MERCON 威 V. Refer to your Scheduled Maintenance Guide to determine the correct service interval. 2 Indicates only approximate dry-fill capacity. Some applications may v...

Item Ford PartName orequivalent Ford PartNumber FordSpecification Transfer caseFront OutputSlip Shaft PremiumLong-LifeGrease XG-1-C or XG-1-K ESA-M1C75-B Windshieldwasher fluid MotorcraftPremiumWindshieldWasherConcentrate ZC—32–A WSB-M8B16–A2 1 Ensure the correct automatic transmission fluid is used...

VEHICLE DIMENSIONS Dimensions 4-Door 4x2 or 4x4 XLT Model -Inches (mm) (1) Overall length 191.6 (4866.7) (2) Overall width 73.7 (1870.9) (2) Overall width includingoutside mirrors 83.9 (2130.8) (3) Maximum height 70.0 (1777.5) (3) Maximum height* withcrossbar 71.9 (1825.4) (4) Wheelbase 113.7 (2889)...

Vehicle identification number The vehicle identification number(VIN) is a 17 digit combination ofletters and numbers. The VIN isattached to a metal tag and islocated on the driver sideinstrument panel. The VIN numberis also found on the Certificationlabel. (Please note that in thegraphic XXXX is rep...

GENUINE FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of Genuine Ford Accessories are available for your vehiclethrough your local authorized Ford or Ford of Canada dealer. These qualityaccessories have been specifically engineered to fulfill your automotiveneeds; they are custom designed to co...

A Accessory delay ..........................69 AdvanceTrac ..............................206 Air bag supplemental restraintsystem ................................135, 140 and child safety seats ............137description ......................135, 140disposal ....................................143d...

idle speed control ...................278lubricationspecifications ..................304, 306refill capacities ........................302service points ..................270–271starting after a collision .........234 Engine block heater .................203 Engine oil .................................