Fisher & Paykel WH8560P3 - Manuals

7 INSTALLATION GUIDE Accessories Check if you received the following accessories with your Fisher & Paykel washer. You will find them inside the drum or attached to the packaging. z 1 x hot inlet hose (grey with red connectors) for WH8560F, WH8560P2, WH8060F, WH8060P2 and WH7560P z 1 x cold inle...

INSTALLATION GUIDE 8 Removing transit safety bolts z The clothes washer is fitted with transit safety bolts at the rear to avoid possible damage to the internal components during transportation. z The four transit bolts must be removed prior to operation of the washer. Failure to remove these will r...

INSTALLATION GUIDE 9 Product dimensions FRONT PLAN E G H I F D MIN. CLEARANCES WH1060P/J WH9060P/J WH8560F/P/J WH8060F/P WH7560P/J WH8060J MM MM MM MM MM MM E Cavity width 640 640 640 640 640 640 F Cavity depth 650 650 650 650 610 610 G Rear 20 20 20 20 20 20 H Sides*** 20 20 20 20 20 20 I Door to s...

INSTALLATION GUIDE 10 1 2 3 Before positioning your washer in its final position, check that the machine is level, front to back and side to side. Level the washer side to side: 1 Place the level on the centre front of the washer. 2 If you need to adjust the washer’s position, loosen the lock nut us...

INSTALLATION GUIDE 11 Water supply Water supply requirements If you have an uncontrolled water heating source (eg a wet back or solar heating system) you should fit a tempering valve. This will ensure the hot water temperature remains within safe limits. Contact your registered plumber to select and...

INSTALLATION GUIDE 12 Draining 20mm max. Place the drain hose in a tub or standpipe Attach drain hose to spigot In multi-storey apartments or any upper floor, the washer should be installed on a floor equipped with a drain. Draining must comply with local by-laws. 1 Flex the guide apart and pull the...

INSTALLATION GUIDE 13 Complete your installation z Turn on the water and check all hose connections for leaks. Make sure there are no kinks in the hose(s). Check the hose connections for leaks again after 24 hours. z Uncoil power cord, remove and discard the plastic pin cover, and plug into the wall...

15 BEFORE YOUR FIRST WASH Check you have done everything you need to before you start your first wash: … Have the packaging and transit bolts been removed? … Is the washer correctly levelled, feet are extended and cabinet corners are clear of the floor? … Is the drain hose threaded through the hose ...

16 SAFETY FEATURES Door lock The door of your washer will lock once you press and will stay locked until the washer beeps at the end of the cycle, ensuring safety for you and your family while your washer is operating. To unlock the door during a cycle Add a Garment (F/P models) The ADD A GARMENT fu...

17 When power is restored, your washer will resume the interrupted wash cycle. If the cycle doesn’t resume automatically, simply press to restart your washer. SAFETY FEATURES Opening the door during a power failure If there is a power failure during a wash cycle your washer will stop and the door wi...

18 CONTROL PANEL 1 Power Press to turn the washer ON/OFF. 2 Keylock Press to disable all buttons on the control panel, except the POWER button. This prevents accidental button presses. 3 SmartTouch™ Control Dial Rotate to select your desired wash cycle. z Red LED illuminates to indicate the selected...

22 WASH CYCLES CYCLE DESIGNED FOR MAX. LOAD SIZE (KG)** WASH TEMP. (°C) SPIN SPEED (RPM) Cottons* A comprehensive cycle specifically for normally soiled cotton garments 8.0/8.5 40 (Cold-90) 1400 (0-1400) Everyday A faster cycle designed for mixed loads with normal soil level 8.0/8.5 40 (Cold-90) 140...

27 Detergent type Your washer requires low-sudsing detergent to prevent oversudsing problems. Low sudsing detergent comes in powder, liquid or pod form and is labelled front loading, low suds, high efficiency or HE. Using top loader detergent in your front loader washer may lead to excessive suds fo...

28 WHERE TO PUT THE DETERGENT F/P Model Washers Liquid detergent Detergent is added to the main wash compartment on the left side of the dispenser drawer marked with a  . As the washer fills, water is flushed into this compartment and is mixed with the detergent, the detergent solution is then deliv...

29 Slide it back into the drawer marked . 1 2 WHERE TO PUT THE DETERGENT To replace the liquid detergent compartment To remove the liquid detergent compartment, firmly grasp and twist the left hand side of the internal compartment and pull upwards. 1 Powdered detergent If you wish to use powdered de...

30 J Model Washers Powdered or liquid detergent Detergent is added to the main wash detergent compartment on the left side of the dispensing drawer marked with a  . z As the washer fills, water is flushed through this compartment to deliver a detergent solution into the drum. z If you select the PRE...

31 Sorting Sort items according to colour, fabric type, and soil type. Wash fine, delicate fabrics separately from thick, heavy fabrics. Always separate coloured items from whites, especially when they are new. Colour run could be an issue if you wash items at higher temperatures. Some soils, like m...

32 2 Press to activate your washer. 3 Select your desired wash cycle by turning the Control Dial. The wash cycle icons will illuminate as you turn the dial showing which cycle is selected, along with the default wash cycle settings. GETTING STARTED QUICKLY 1 Open the detergent drawer.Pour liquid or ...

33 GETTING STARTED QUICKLY 6 Use to lock the buttons on the control panel, preventing them from being activated accidently by a washing basket or little fingers, refer to the ‘Wash cycle options’ section. 5 Press to start the cycle. The washer will start to fill with water and select the correct was...

34 WASH CYCLE OPTIONS Once you have selected your wash cycle you may wish to change the default wash options. Wash cycle options All wash cycles default to the recommended options for that cycle based on the average expected load to be washed. You can vary the options (eg WASH TEMP , SPIN SPEED ) to...

35 WASH CYCLE OPTIONS No Spin Selecting NO SPIN will end the cycle after the rinse, allowing you to remove items you wish to drip dry.The washer will complete the default wash and rinse spins for the cycle; only the final spin will not be completed. Remove the items you wish to drip dry and then sel...

36 WASH CYCLE OPTIONS Wash Boost Pre wash (all models) For extra dirty loads you can perform a PRE WASH . Your washer will start the wash with a short wash in cool water to remove excess soil. After this the washer will drain and then fill at the selected temperature for the main wash.Simply press t...

37 Options Soak (WH8560F and WH8060F models only) The SOAK option provides a two-hour soak during the middle of the wash phase of the cycle. The washer will then complete the rest of the cycle. During SOAK , the washer will agitate for a few seconds every minute. SOAK is not available on WOOL, DRUM ...

39 1 Press the button, then press and hold for three seconds. This will activate the control panel. Wash cycles and options can now be selected.If a button is pressed while KEYLOCK is activated, the LED above KEYLOCK will flash. 1 Press for three seconds.When activated, the light above the button is...

40 Delay Start The DELAY START option can delay the start of the wash cycle between five minutes and 12 hours. This can be useful to time your washing to finish when you arrive home from work, or to start once you have finished in the shower. Avoid using DELAY START for damp, non-colourfast items as...

41 CUSTOMISING A WASH CYCLE To customise a cycle You can program your washer to remember the wash options you prefer for each wash cycle. For instance, you may want to set the EVERYDAY cycle to default to a COLD wash or set HEAVY cycle to include a SOAK . 1 Press to activate your washer. 2 Turn the ...

42 CUSTOMISING A WASH CYCLE To change your customised wash cycle simply repeat these steps. 5 Press to store your customised cycle. A long beep will sound to confirm that your changes have been saved.

43 CHANGING PRE-SET OPTIONS Option adjustment mode (Models WH1060P, WH9060P, WH8560P3 and WH8060P3) This allows you to change the CONTROLLED COLD default setting wash temperature to COLD TAP . If your incoming cold water temperature is very low and you choose to do a COLD TAP wash, the wash may be l...

44 Factory reset You can reset your washer to factory default settings by following the steps below. To reset your washer to factory default settings: 1 Select the SPIN cycle. 2 Press MORE , LESS and OPTIONS buttons together for three seconds, will appear on the screen and the washer will beep.Your ...

45 CARING FOR YOUR WASHER 1 To remove the drawer, pull it open, push down on the tab in the fabric softener compartment and pull out. 2 Wipe out the detergent dispenser drawer with a damp cloth. 3 Rinse it under warm water and re-insert. Clean the drawer regularly, especially if you use fabric softe...

46 Cleaning the inside of your washer It is important that you regularly clean the inside of your washer using the DRUM CLEAN cycle. After 100 cycles icon will flash every time you turn your washer on to remind you to do this. If your washer starts to smell this is a sign that you should complete a ...

47 Aside from the detergent dispenser, water hose(s), and the pump filter, no other parts are designed to be removed from the washer for cleaning. Do not attempt to remove any other part of the washer. Cleaning the drum and the door z Use a soft damp cloth to wipe the door, cleaning any water marks ...

48 CARING FOR YOUR WASHER Cleaning the pump filter Unhook the pump outlet hose and pull it out (about 150mm). Remove the plug and allow any water (approximately 250ml) to drain into a shallow dish.After the draining process is complete, replace the plug into the hose and refit the hose back into the...

49 CARING FOR YOUR WASHER Products that might damage your washer z Concentrated bleaches, laundry pre-soakers/sanitisers, stain removers and hydrocarbon solvents (eg petrol and paint thinners) can cause damage to the surfaces eg control panel, and components of your washer. z Be careful when washing...

50 BEFORE YOU CALL FOR SERVICE User warnings Your washer is capable of self diagnosis and may sound a series of beeps and display a notification or warning to inform you when there is a problem. In most cases you will be able to address the problem the washer is alerting you to. Check this chart bef...

51 BEFORE YOU CALL FOR SERVICE PROBLEM DISPLAYED AS WHAT TO DO The washer has too many suds Washer will stop and flash while waiting for suds to dissipate. The washer will not beep during this time. When the suds have dissipated the washer will automatically restart. If a suds event has occurred dur...

52 FAULT CODES When a continuous series of beeps is sounded, all the lights turn off on the control panel and a number appears on the display, a fault has occurred. The washer will automatically enter this mode if a fault occurs. The fault code will be displayed as followed by a number on the digita...

53 TROUBLESHOOTING The following is a list of problems you may encounter when using this appliance and some suggestions that may help to correct the problem. If you still have problems, contact your Fisher & Paykel trained and supported service technician. PROBLEM POSSIBLE CAUSES WHAT TO DO Wash...

59 For New Zealand and Australia only. You automatically receive a two-year Manufacturer’s Warranty with the purchase of this clothes washer covering parts and labour for servicing within the country of purchase. Fisher & Paykel undertakes to: Repair or, at its option, replace without cost to th...

60 MANUFACTURER’S WARRANTY Nothing in this Manufacturer’s Warranty is intended to, nor limits, any rights you may have under law to recover the costs of inspecting or returning the goods to us.This product has been designed for use in a normal domestic (residential) environment. This product is not ...

61 CUSTOMER CARE Before you call for service or assistance: Check our website, fisherpaykel.com, for ‘Product Help’ to see the latest updates, hints and tips, and information about your product. We recommend that you also refer to your user guide to ensure: 1 Your product is correctly installed. 2 Y...

62 CUSTOMER CARE Registration Register your product with us so we can provide you with the best service possible. To register your product visit our website: fisherpaykel.com Complete and keep for safe reference: Model Serial No. Purchase Date Purchaser Dealer Suburb Town Country