Fisher & Paykel DD60SI9 - Manuals

5 3 PRODUCT DIMENSIONS B D N E A G H I J C F M L K PLAN PROFILE FRONT DD60DI DD60DHI PRODUCT DIMENSIONS MM A Overall height of product 1, 2 820-880 B Overall width of product 599 C Overall depth of product 3 571 D Depth of chassis (to back of front drawer panel) 553 E Depth of drawer front panel 16-...

6 Q P O R S 4 CABINETRY DIMENSIONS Minimum clearances from adjacent cabinetry min. 13 mmclearance from a cornercupboard Bracket slots min. 2 mmclearance to adjacent cupboard door PROFILE PLAN DD60DI DD60DHI CABINETRY DIMENSIONS MM O Inside height of cavity* min. 820 P Inside width of cavity 600 Q In...

7 5 CUSTOM DRAWER PANEL CALCULATIONS The following calculations assume the top of the upper panel is aligned with the top of the adjacent cabinetry. The final panel/cabinetry alignment is achieved by adjusting the feet: WIDTH OF ALL PANELS Measure A (the width between adjacent door/drawer fronts) an...

8 6 CUSTOM TOEKICK PANEL CALCULATIONS HEIGHT OF THE TOEKICK PANEL Measure D (height from the top of adjacent cabinet door fronts to the floor) and write it in the first box below, then complete the equation. Clearance to floor (min. 12mm) Toekick Depth For a Toekick Depth 40mm Depth is measured from...

9 7 CAVITY PREPARATION Water Connection Recommended COLD (Maximum 60°C). 3/4“ BSP (GB20) to suit flat washer. Kosher requirements Drains will need to be separated to satisfy kosher requirements. We suggest you confirm acceptability with your local rabbi in respect to kosher installations. Water Pres...

10 8 MAXIMUM DISTANCE OF HOSES & CORD FROM CHASSIS EDGE LEFT HAND SIDE Drain hoses - 2000mm Drain hoses - 1800mm Inlet hose - 1650mm Inlet hose - 1250mm Power cord (excl.plug) - 1650mm Power cord (excl.plug) - 1650mm RIGHT HAND SIDE

11 (x2) 9 RECOMMENDED METHOD (A) - SECURE WITHOUT DRAWER REMOVAL (FRAMELESS CABINETRY ONLY) NOW CHOOSE WHICH INSTALLATION METHOD (A) OR (B) IS MORE SUITABLE FOR YOUR CABINETRY... As you push product in, pull through hoses and cord, ensuring they don’t get kinked or twisted. optionally attach the two...

13 (x2) 1 2 4 4 3 3 9 ALTERNATIVE METHOD (B) - SECURE BY DRAWER REMOVAL As you push product in, pull through hoses and cord, ensuring they don’t get kinked or twisted. optionally attach the two top mounting brackets Initially level the product You can raise or lower the product by twisting the feet....

15 !4 INSTALLING CUSTOM FRONT DRAWER PANELS 1 1 2 Electrical Shock Hazard WARNING! Before continuing, ensure that the product is disconnected from the power supply.Failure to follow this warning may result inelectrical shock, injury or fire. 3 1 1 !4 - A REMOVE BOTH PANEL BRACKETS FROM PRODUCT Remove...

16 !4 INSTALLING CUSTOM FRONT DRAWER PANELS 2 3 2 16mm (x6) 4 1 1 2 16mm (x3) !4 - C ATTACH CUSTOM PANELS TO PANEL BRACKETS There must be at least3 screws used each side. IMPORTANT! ● Ensure the Knock-To-Pause module is orientated correctly before attaching. ● Ensure the module is centralized in the...

18 !5 FITTING A CUSTOM TOEKICK PANEL PROFILE A PROFILE B 9 Custom Toekick Panel Toekick panel cutting template Custom toekick panel Toekick mounting bracket cutting template Toekick mounting bracket Align panel with the ribs Toekick Depth For a Toekick Depth 40mm Depth is measured from FRONT of door...

19 !6 FIT THE SUPPLIED PREFINISHED TOEKICK PANEL (IF PREFERRED) 1 2 3 4 19 19 5 6 8 9 7 IMPORTANT! Do not overtighten screw. Slide the toekick onto the mounting rails either side and screw the toekick onto the bottom of tub on either side. Where the toekick meets the bottom of the tub is the cut-off...

20 !7 THERE ARE TWO DIFFERENT PLUMBING AND DRAINAGE OPTIONS. CHOOSE WHICH IS MORE SUITABLE. 1 2 1 2 3 If space is limited for fixing, push hose through drain hose support to required height If space is limited for fixing, push hose through drain hose support to required height Dishwasher using drain...

21 Ensure the supplied rubber washer is fitted inside the coupling. Tighten coupling with spanner. 180 o No leaks! 1 2 min. 10mm 3/4” BSP connector !6 CONNECT INLET HOSE TO COLD WATER !7 PLUG PRODUCT IN !8 TROUBLESHOOTING ● Excessive water remaining above the filter plate, after the rinse cycle. (Th...

22 !9 FINAL CHECKLIST TO BE COMPLETED BY THE INSTALLER Complete and keep for safe reference: Model Serial No. Purchase Date Purchaser Dealer Address Installer’s Name Installer’s Signature Installation Company Installation Date Check all parts are installed. Ensure that all panels and parts thereof a...

5 9 1 3 8 3 A 0 8 .1 7 I N S TA L L AT I O N G U I D E N Z A U G B I E DD60SI, DD60STI, DD60SLI, DD60SHI & DD60SHTI models S I N G L E D I S H D R AW E R T M D I S H WA S H E R

7 5 CUSTOM DRAWER PANEL CALCULATIONS The following calculations assume the top of the upper panel is aligned with the top of the adjacent cabinetry. WIDTH OF THE PANEL Measure A (the width between adjacent door/drawer fronts) and write it in the first box below, then complete the equation. HEIGHT OF...

9 ø 60mm ø 60mm ø 60mm max. 5mm max. 5mm 220mm 220mm 100mm 100mm ø60mm Services can be located either side of dishwasher The ø 60mm services hole should be enlarged to accomodate the extra venting hose by cutting out some material from the bottom corner. VENT HOSE VENT HOSE& SERVICES SERVICES Sh...

12 As you push product in, pull through hoses and cord, ensuring they don’t get kinked or twisted. IMPORTANT! If product cannot be pushed in far enough, pull out again and rearrange hoses and cord. Do not use excessive force, as doing so may squash the hoses and lead to incorrect operation. 2 1 3 Op...

13 !0 ALTERNATIVE METHOD (B) - SECURE BY DRAWER REMOVAL !0 - A ATTACH VENTING HOSE Fitted Elbow Check that the fitted elbow is rotated left or right (depending on the direction of the routing), then ensure the venting hose is securely attached to it. As you push product in, pull through hoses and co...

16 !6 INSTALLING A CUSTOM FRONT DRAWER PANEL 1 1 2 Electrical Shock Hazard WARNING! Before continuing, ensure that the product is disconnected from the power supply.Failure to follow this warning may result inelectrical shock, injury or fire. 3 1 1 !6 - A REMOVE PANEL BRACKET FROM PRODUCT Remove side...

18 !6 INSTALLING CUSTOM FRONT DRAWER PANELS !6 - E CONNECT THE KNOCK-TO-PAUSE MODULE TO THE CONTROLLER !6 - G ATTACH CUSTOM PANEL TO PRODUCT !6 - F RECONNECT THE EARTH WIRE TO THE PANEL BRACKET !6 - H ADJUST CUSTOM PANEL HEIGHT TO ALIGN CABINETRY GAPS 2 2 1 Controller Ensure the Knock-To-Pause Modul...

21 @0 TROUBLESHOOTING ● Excessive water remaining above the filter plate, after the rinse cycle. (This is displayed as an A3 fault. See user guide ‘How to attend to a fault’) Check for a kinked drain hose, blocked or incorrectly drilled out waste connection, highloop not properly installed, drain ho...