Page 3 - SAFETY AND WARNINGS
2 1 SAFETY AND WARNINGS WARNING! Electrical shock hazardBefore installing the dishwasher, remove the house fuse or open the circuit breaker.This appliance must be earthed. In the event of a malfunction or breakdown, earthing will reduce the risk of electric shock by providing a path of least resista...
Page 4 - Be sure to leave these Instructions with the Customer.; IMPORTANT SAFETY INSTRUCTIONS; SAVE THESE INSTRUCTIONS
3 1 SAFETY AND WARNINGS IMPORTANT SAFETY INSTRUCTIONS ● Installation of this dishwasher requires basic mechanical and electrical skills. ● Be sure to leave these Instructions with the Customer. ● Installation must comply with your local building and electricity regulations. ● At the completion of th...
Page 5 - PARTS SUPPLIED
4 2 PARTS SUPPLIED If the Drain hoses supplied are not long enough to reach your services, you must use a Drain Hose Extension Kit P/N 525798 which will extend the drain hoses by 3.6 m. The kit is available from the nearest Fisher & Paykel Authorised Service Centre or our website. Clamp (1) (for...
Page 6 - PRODUCT DIMENSIONS
5 3 PRODUCT DIMENSIONS B D N E A G H I J C F M L K PLAN PROFILE FRONT DD60DI DD60DHI PRODUCT DIMENSIONS MM A Overall height of product 1, 2 820-880 B Overall width of product 599 C Overall depth of product 3 571 D Depth of chassis (to back of front drawer panel) 553 E Depth of drawer front panel 16-...
Page 7 - CABINETRY DIMENSIONS
6 Q P O R S 4 CABINETRY DIMENSIONS Minimum clearances from adjacent cabinetry min. 13 mmclearance from a cornercupboard Bracket slots min. 2 mmclearance to adjacent cupboard door PROFILE PLAN DD60DI DD60DHI CABINETRY DIMENSIONS MM O Inside height of cavity* min. 820 P Inside width of cavity 600 Q In...
Page 8 - CUSTOM DRAWER PANEL CALCULATIONS; WIDTH OF ALL PANELS; FRONT PANEL MATERIAL SPECIFICATIONS
7 5 CUSTOM DRAWER PANEL CALCULATIONS The following calculations assume the top of the upper panel is aligned with the top of the adjacent cabinetry. The final panel/cabinetry alignment is achieved by adjusting the feet: WIDTH OF ALL PANELS Measure A (the width between adjacent door/drawer fronts) an...
Page 9 - CUSTOM TOEKICK PANEL CALCULATIONS; HEIGHT OF THE TOEKICK PANEL; HEIGHT OF; TOEKICK PANEL MATERIAL SPECIFICATIONS
8 6 CUSTOM TOEKICK PANEL CALCULATIONS HEIGHT OF THE TOEKICK PANEL Measure D (height from the top of adjacent cabinet door fronts to the floor) and write it in the first box below, then complete the equation. Clearance to floor (min. 12mm) Toekick Depth For a Toekick Depth 40mm Depth is measured from...
Page 10 - CAVITY PREPARATION; Water Connection; COLD; BENCHTOP
9 7 CAVITY PREPARATION Water Connection Recommended COLD (Maximum 60°C). 3/4“ BSP (GB20) to suit flat washer. Kosher requirements Drains will need to be separated to satisfy kosher requirements. We suggest you confirm acceptability with your local rabbi in respect to kosher installations. Water Pres...
Page 11 - MAXIMUM DISTANCE OF HOSES & CORD FROM CHASSIS EDGE; LEFT HAND SIDE
10 8 MAXIMUM DISTANCE OF HOSES & CORD FROM CHASSIS EDGE LEFT HAND SIDE Drain hoses - 2000mm Drain hoses - 1800mm Inlet hose - 1650mm Inlet hose - 1250mm Power cord (excl.plug) - 1650mm Power cord (excl.plug) - 1650mm RIGHT HAND SIDE
Page 12 - ATTACH SIDE MOUNTING BRACKETS
11 (x2) 9 RECOMMENDED METHOD (A) - SECURE WITHOUT DRAWER REMOVAL (FRAMELESS CABINETRY ONLY) NOW CHOOSE WHICH INSTALLATION METHOD (A) OR (B) IS MORE SUITABLE FOR YOUR CABINETRY... As you push product in, pull through hoses and cord, ensuring they don’t get kinked or twisted. optionally attach the two...
Page 14 - Initially level the product; PULL THROUGH HOSES & PUSH INTO THE CAVITY; To prevent kinked hoses
13 (x2) 1 2 4 4 3 3 9 ALTERNATIVE METHOD (B) - SECURE BY DRAWER REMOVAL As you push product in, pull through hoses and cord, ensuring they don’t get kinked or twisted. optionally attach the two top mounting brackets Initially level the product You can raise or lower the product by twisting the feet....
Page 16 - INSTALLING CUSTOM FRONT DRAWER PANELS; REMOVE BOTH PANEL BRACKETS FROM PRODUCT; Repeat for the other drawer.
15 !4 INSTALLING CUSTOM FRONT DRAWER PANELS 1 1 2 Electrical Shock Hazard WARNING! Before continuing, ensure that the product is disconnected from the power supply.Failure to follow this warning may result inelectrical shock, injury or fire. 3 1 1 !4 - A REMOVE BOTH PANEL BRACKETS FROM PRODUCT Remove...
Page 17 - Use all 3 screws provided.; TO CUSTOM PANELS
16 !4 INSTALLING CUSTOM FRONT DRAWER PANELS 2 3 2 16mm (x6) 4 1 1 2 16mm (x3) !4 - C ATTACH CUSTOM PANELS TO PANEL BRACKETS There must be at least3 screws used each side. IMPORTANT! ● Ensure the Knock-To-Pause module is orientated correctly before attaching. ● Ensure the module is centralized in the...
Page 19 - FITTING A CUSTOM TOEKICK PANEL; Custom Toekick Panel; Do not overtighten screw.
18 !5 FITTING A CUSTOM TOEKICK PANEL PROFILE A PROFILE B 9 Custom Toekick Panel Toekick panel cutting template Custom toekick panel Toekick mounting bracket cutting template Toekick mounting bracket Align panel with the ribs Toekick Depth For a Toekick Depth 40mm Depth is measured from FRONT of door...
Page 20 - FIT THE SUPPLIED PREFINISHED TOEKICK PANEL (IF PREFERRED); Prefinished Toekick Panel
19 !6 FIT THE SUPPLIED PREFINISHED TOEKICK PANEL (IF PREFERRED) 1 2 3 4 19 19 5 6 8 9 7 IMPORTANT! Do not overtighten screw. Slide the toekick onto the mounting rails either side and screw the toekick onto the bottom of tub on either side. Where the toekick meets the bottom of the tub is the cut-off...
Page 21 - Dishwasher using drain hose joiner onto sink trap/waste tee; Dishwasher and Ø 38 mm Standpipe
20 !7 THERE ARE TWO DIFFERENT PLUMBING AND DRAINAGE OPTIONS. CHOOSE WHICH IS MORE SUITABLE. 1 2 1 2 3 If space is limited for fixing, push hose through drain hose support to required height If space is limited for fixing, push hose through drain hose support to required height Dishwasher using drain...
Page 22 - CONNECT INLET HOSE TO COLD WATER
21 Ensure the supplied rubber washer is fitted inside the coupling. Tighten coupling with spanner. 180 o No leaks! 1 2 min. 10mm 3/4” BSP connector !6 CONNECT INLET HOSE TO COLD WATER !7 PLUG PRODUCT IN !8 TROUBLESHOOTING ● Excessive water remaining above the filter plate, after the rinse cycle. (Th...
Page 23 - FINAL CHECKLIST; TO BE COMPLETED BY THE INSTALLER; F I S H E R PAY K E L .C O M
22 !9 FINAL CHECKLIST TO BE COMPLETED BY THE INSTALLER Complete and keep for safe reference: Model Serial No. Purchase Date Purchaser Dealer Address Installer’s Name Installer’s Signature Installation Company Installation Date Check all parts are installed. Ensure that all panels and parts thereof a...
Page 24 - S I N G L E D I S H D R AW E R; T M; D I S H WA S H E R
5 9 1 3 8 3 A 0 8 .1 7 I N S TA L L AT I O N G U I D E N Z A U G B I E DD60SI, DD60STI, DD60SLI, DD60SHI & DD60SHTI models S I N G L E D I S H D R AW E R T M D I S H WA S H E R
Page 31 - WIDTH OF THE PANEL; HEIGHT OF THE PANEL; WIDTH OF PANEL
7 5 CUSTOM DRAWER PANEL CALCULATIONS The following calculations assume the top of the upper panel is aligned with the top of the adjacent cabinetry. WIDTH OF THE PANEL Measure A (the width between adjacent door/drawer fronts) and write it in the first box below, then complete the equation. HEIGHT OF...
Page 33 - PREPARATION FOR EXTERNAL VENTING THROUGH SAME CABINET; External Venting Kit
9 ø 60mm ø 60mm ø 60mm max. 5mm max. 5mm 220mm 220mm 100mm 100mm ø60mm Services can be located either side of dishwasher The ø 60mm services hole should be enlarged to accomodate the extra venting hose by cutting out some material from the bottom corner. VENT HOSE VENT HOSE& SERVICES SERVICES Sh...
Page 36 - Airflow
12 As you push product in, pull through hoses and cord, ensuring they don’t get kinked or twisted. IMPORTANT! If product cannot be pushed in far enough, pull out again and rearrange hoses and cord. Do not use excessive force, as doing so may squash the hoses and lead to incorrect operation. 2 1 3 Op...
Page 37 - ATTACH VENTING HOSE; Fitted Elbow; PULL THROUGH HOSES & MOVE INTO THE CAVITY
13 !0 ALTERNATIVE METHOD (B) - SECURE BY DRAWER REMOVAL !0 - A ATTACH VENTING HOSE Fitted Elbow Check that the fitted elbow is rotated left or right (depending on the direction of the routing), then ensure the venting hose is securely attached to it. As you push product in, pull through hoses and co...
Page 40 - INSTALLING A CUSTOM FRONT DRAWER PANEL; REMOVE PANEL BRACKET FROM PRODUCT; Side Pin
16 !6 INSTALLING A CUSTOM FRONT DRAWER PANEL 1 1 2 Electrical Shock Hazard WARNING! Before continuing, ensure that the product is disconnected from the power supply.Failure to follow this warning may result inelectrical shock, injury or fire. 3 1 1 !6 - A REMOVE PANEL BRACKET FROM PRODUCT Remove side...
Page 42 - Repeat on the other side if necessary.
18 !6 INSTALLING CUSTOM FRONT DRAWER PANELS !6 - E CONNECT THE KNOCK-TO-PAUSE MODULE TO THE CONTROLLER !6 - G ATTACH CUSTOM PANEL TO PRODUCT !6 - F RECONNECT THE EARTH WIRE TO THE PANEL BRACKET !6 - H ADJUST CUSTOM PANEL HEIGHT TO ALIGN CABINETRY GAPS 2 2 1 Controller Ensure the Knock-To-Pause Modul...
Page 45 - TROUBLESHOOTING
21 @0 TROUBLESHOOTING ● Excessive water remaining above the filter plate, after the rinse cycle. (This is displayed as an A3 fault. See user guide ‘How to attend to a fault’) Check for a kinked drain hose, blocked or incorrectly drilled out waste connection, highloop not properly installed, drain ho...
