Fisher & Paykel DD60SCX9 - Manuals

4 3 PRODUCT DIMENSIONS N F C L M A G B E D O I H J K L PLAN PROFILE PROFILE DD60DC MODELS DD60DA MODELS FRONT DD60DA DD60DC PRODUCT DIMENSIONS MM MM A Overall height of product 1 820-880 2 820-880 2 B Overall width of product 599 599 C Overall depth of product 573 573 D Depth of chassis (to back of ...

5 4 CABINETRY DIMENSIONS Minimum clearances from adjacent cabinetry min. 13 mmclearance from a cornercupboard Bracket slots min. 2 mmclearance to adjacent cupboard door R Q P S T PROFILE PLAN DD60DA DD60DC CABINETRY DIMENSIONS MM MM P Inside height of cavity* min. 820 min. 820 Q Inside width of cavi...

6 Service Holes Can be located either side of dishwasher, close to the rear face and the floor, as illustrated, for access to the water supply and drain. O If the hole is through wood, make sure its edges are smooth and rounded. O If the hole is through metal, ensure you fit the supplied Edge Protec...

7 6 MAXIMUM DISTANCE OF HOSES & CORD FROM CHASSIS EDGE LEFT HAND SIDE Drain hoses - 2000 mm Drain hoses - 1800 mm Inlet hose - 1650 mm Inlet hose - 1250 mm Power cord (excl.plug) - 1650 mm Power cord (excl.plug) - 1650 mm RIGHT HAND SIDE

8 (x2) 7 RECOMMENDED METHOD (A) - SECURE WITHOUT DRAWER REMOVAL (FRAMELESS CABINETRY ONLY) NOW CHOOSE WHICH INSTALLATION METHOD (A) OR (B) IS MORE SUITABLE FOR YOUR CABINETRY... As you push product in, pull through hoses and cord, ensuring they don’t get kinked or twisted. optionally attach the two ...

10 (x2) 1 2 4 4 3 3 7 ALTERNATIVE METHOD (B) - SECURE BY DRAWER REMOVAL As you push product in, pull through hoses and cord, ensuring they don’t get kinked or twisted. optionally attach the two top mounting brackets Initially level the product You can raise or lower the product by twisting the feet....

12 !4 FIT THE SUPPLIED TOEKICK PANEL - DD60DA MODELS ONLY if after fitting, the drawer touches the floor with a full load, you need to remove more of the toekick panel: A Remove the lower drawer (see ALTERNATIVE METHOD (B) - SECURE BY DRAWER REMOVAL - STEP 8 B: REMOVE THE LOWER DRAWER) B Remove the ...

13 !4 FIT THE SUPPLIED TOEKICK PANEL - DD60DC MODELS ONLY 19 1 3 5 7 8 9 2 6 4 19 IMPORTANT! Do not overtighten screw. Where the toekick meets the bottom of the tub is the cut-off point Mark this point on the toekick with a pencil Lay the toekick face down on a chopping board or similiar Smooth the ...

14 1 2 3 1 2 !5 THERE ARE TWO DIFFERENT PLUMBING AND DRAINAGE OPTIONS. CHOOSE WHICH IS MORE SUITABLE. DRAINAGE OPTION 2 Dishwasher using drain hose joiner onto sink trap/waste tee min. radius200 mm 7 50 - 883 mm 7 50 - 883 mm min. 500 mm min. 500 mm min. radius200 mm step 16 step 16 Supplied drain h...

15 Ensure the supplied rubber washer is fitted inside the coupling. Tighten coupling with spanner. 180 o No leaks! 1 2 min. 10mm 3/4” BSP connector !6 CONNECT INLET HOSE TO COLD WATER !7 PLUG PRODUCT IN !8 TROUBLESHOOTING O Excessive water remaining above the filter plate, after the rinse cycle. (Th...

16 !9 FINAL CHECKLIST TO BE COMPLETED BY THE INSTALLER Complete and keep for safe reference: Model Serial No. Purchase Date Purchaser Dealer Address Installer’s Name Installer’s Signature Installation Company Installation Date Check all parts are installed. Ensure that all panels and parts thereof a...

DD60SA & DD60SC models S I N G L E D I S H D R AW E R ™ D I S H WA S H E R 5 9 1 1 5 1 D 0 5 .1 9 I N S TA L L AT I O N G U I D E N Z A U G B I E S G

5 4 CABINETRY DIMENSIONS Minimum clearances from adjacent cabinetry min. 13 mmclearance from a cornercupboard min. 2 mmclearance to adjacent cupboard door M L K PROFILE PLAN DD60SA DD60SC DD60SCT CABINETRY DIMENSIONS MM MM K Inside height of cavity min. 412 min. 456 L Inside width of cavity 600 600 ...

9 2 1 3 !0 - A SECURE TO THE CABINETRY ON THE SIDES Open the drawer halfway.Using a flat bladed screwdriver, prise the grey rubber plug out of the trim moulding. Replace the grey rubber plug back into the trim moulding and ensure the trim seal is facing forward. Repeat for all four brackets. Using a...

11 1 2 1 2 3 4 100 mm !1 - B REFIT THE DRAWER ONTO THE RUNNERS !0 - B SECURE TO THE CABINETRY ON THE SIDES Before refitting the drawer, ensure the hoses are not twisted and the latches at the rear of each drawer runner are facing forward. Lift or rotate anti-clockwise the drawer back onto the drawer...

12 3 1 2 1 2 !2 THERE ARE TWO DIFFERENT PLUMBING AND DRAINAGE OPTIONS. CHOOSE WHICH IS MORE SUITABLE. DRAINAGE OPTION 2 Dishwasher using drain hose joiner onto sink trap/waste tee min. radius200 mm 7 50 - 883 mm 7 50 - 883 mm min. 500 mm min. 500 mm min. radius200 mm step 13 step 13 Supplied drain h...

14 !5 TROUBLESHOOTING O Excessive water remaining above the filter plate, after the rinse cycle. (This is displayed as an A3 fault) Check for a kinked drain hose, blocked waste connection, highloop not properly installed, drain hose not routed correctly or spray arm not in place. O No water supply. ...