Fisher & Paykel DD60D2NX9 - Manuals

6 PRODUCT DIMENSIONS – DD60DA MODELS PRODUCT DIMENSIONS DD60DA MM A Overall height* 820 – 880 B Overall width 599 C Overall depth 573 D Height of chassis 811 E Depth of chassis 553 F Height of upper door panel 393 G Height of lower door panel 312 H Depth of door panel 20 I Ventilation gap between do...

7 PRODUCT DIMENSIONS – DD60DD MODELS Actual product dimensions may vary by ± 2 mm PLAN ISOMETRIC PROFILE FRONT a F g B C d E o h i q p j l n m PRODUCT DIMENSIONS DD60DD MM A Overall height* 820 – 880 B Overall width 599 C Overall depth 573 D Height of chassis 811 E Depth of chassis 553 F Height of u...

8 PRODUCT DIMENSIONS DD60DN MM A Overall height* 820 - 880 B Overall width 599 C Overall depth 573 D Height of chassis 811 E Depth of chassis 553 F Depth of door panel 20 G Height of upper door panel 398 H Height of lower door panel 309 I Ventilation gap between door panels 11 J Height from top of d...

9 CABINETRY CABINETRY DIMENSIONS MM A Minimum inside height* 820 B Inside width 600 – 610 C Minimum inside depth** 579 D Recommended height of adjacent cabinetry 720 E Height of toe kick area*** 100 – 160 *depending on adjustment of levelling feet**including 19mm door panels on adjacent cabinetry***...

10 PLUMBING & ELECTRICAL CONSIDERATIONS SERVICE DIMENSION LEFT SIDE* RIGHT SIDE* MM MM A Length of drain hoses 2000 1800 B Length of power cord** 1650 1650 C Length of inlet hose 1650 1250 D Distance from floor to top of hose support 750 – 883 750 – 883 E Minimum distance from floor to end of dr...

11 CABINETRY PREPARATION SERVICE ACCESS MOISTURE PROTECTION SIDE PARTITION SELECT CABINETRY SECURING METHOD SERVICE HOLE DIMENSIONS MM A Maximum distance between rear of cavity and service hole 5 B Maximum distance between floor and service hole 10 C Minimum diameter of service hole 57 REAR WALL REA...

12 SECURE TO CABINETRY VIA BRACKETS (METHOD A) Secure all four side brackets to the DishDrawer™ Dishwasher, aligning bracket A with slot A and bracket B with slot B. Ensure the ends of the brackets are not pushed into the chassis. 1 5 2 6 3 7 4 8 Push the product into the cavity, pulling the hoses t...

13 SECURE TO CABINETRY VIA DRAWER REMOVAL (METHOD B) Optionally, fit the two top brackets. Ensure the ends of the brackets are not pushed into the chassis. Loosen each foot by 1/2 a turn by lightly tilting the product and rotating each leg anticlockwise. Push the product into the cavity, pulling the...

14 INSTALL TOE KICK – DD60DC, DD60DD & DD60DN MODELS Slide toe kick onto the mounting rails and secure Do not over tighten the screws. Carefully score toe kick at desired height Measure toe kick height. Where the toe kick meets the bottom of the tub is the recommended cut-off point. Snap excess ...

15 INSTALL TOE KICK – DD60DA MODELS Measure the distance from the floor to the base of the lower door panel. Refer to the table below for the recommended cut location. Punch or drill out the two mounting holes with a 5mm drill bit on each side of the toe kick as shown. Secure toe kick to the Dishdra...

17 TO BE COMPLETED BY THE INSTALLER … Check all parts are installed correctly and are secure. … Ensure all clearance gaps have been maintained. … Ensure DishDrawer™ Dishwasher is securely fastened to the cabinetry and drawer opens and closes freely with no resistance. … Ensure any packaging or tape ...

18 TROUBLESHOOTING No program indicator lights up when the drawer is opened z Ensure power is connected and is switched on. z AUTO POWER-ON may need to be activated. Refer to your user guide for details. Drawer doesn’t close properly z Ensure nothing is obstructing the drawer from closing such as ho...

4 3 1 3 74 A 03 . 2 3 F I S H E R PAY K E L .CO M © Fisher & Paykel Appliances 2023. All rights reserved. The models shown in this guide may not be available in all markets and are subject to change at any time. The product specifications in this guide apply to the specific products and models d...