EverFocus EPTZ900 - Manuals

EverFocus EPTZ900 – Manual in PDF format online.

Manuals:

Manual

Manual EverFocus EPTZ900

Summary

Page 2 - Table of Contents

1-1 Table of Contents 1. EPTZ900/500 OVERVIEW ................................................ 1-3 1.1. Introduction .............................................................................................1-3 1.2. Specifications ...........................................................

Page 9 - short to be connected to a wrong connector when putting them back.; RELAY

1-8 1.3.2. Base Board The base board that is on the bottom of the housing connects to power cable, video cable, control cable, alarm cable, fan and heater (fan and heater are for EPTZ900 only). In order to connect to cables, the board needs to be taken off, and put back after finishing connecting to...

Page 10 - CPU

1-9 RELAY JP5 V ide o + V ide o - R S 48 5 + R S 48 5 - AC 2 4 AC 2 4 EPTZ500 Baseboard 1.3.3. EPTZ900/500 Control Board The PCB board with two dipswitches is the control board of speed dome. The two switches are used to set address, protocol, Baud Rate, video format and terminator resistance. SW1 O...

Page 12 - speed dome via the keyboard.

1-11 1.5. EPTZ900/500 Quick Operation Guide (Work with EKB500) EPTZ900/500 and EKB500 (Keyboard) can work together by using factory default setting. You just need to connect cables by following the steps: 1. Connect the RS485 cable to EPTZ900/500 and a Keyboard (EKB500). 2. Connect a video cable fro...

Page 13 - Power Cable

2-12 2. EPTZ900/500 INSTALLATION 2.1. Packing List There are 3 boxes that are housing, bulb and mechanical part with a camera module, one wall mount bracket, one power adapter and one accessory packet in the package. The detail accessories list below: ¾ Housing x1 ¾ Bulb x1 ¾ Mechanical part with a ...

Page 14 - Video Cable; may be needed if the video cable is too long.; Control Cable; as a keyboard or a DVR.

2-13 z Video Cable A BNC cable is used for connecting a speed dome to a DVR or a monitor. An amplifier may be needed if the video cable is too long. z Control Cable Basically, EPTZ900/500 uses a differential pair to connect to other devices by cascading. A cable that has low signal decline can be us...

Page 19 - bits of the SW2 on the PCB board are used to set the video format. The; PAL; enable a new value after changing.; OFF

2-18 2.3.4. Video Format Setting The 6 th bits of the SW2 on the PCB board are used to set the video format. The default video format depends on the factory setting. Please do not change it. ON 12345 678 SW 2 Protocol Baud Rate PAL / NTSC Maching Resistance ON 12345 6 78 PAL NTSC ON 12345 6 78 Notic...

Page 20 - Control Unit; Ternimator; the terminator resistance ON.

2-19 CAM-0 CAM-1 CAM-n Keyboard DVR RS485 Control Unit n ≦ 255 Ternimator Resistance ON Note: When the dome is out of control, or does not work under control well, try to switch the terminator resistance ON. Notice: Please make sure the power is off before setting, and restart the speed dome to enab...

Page 22 - M5 Bolt; Hex Allen wrench; baseboard in the housing by screwing 4 bolts on it.

2-21 2. Thread the cable through the hole in the wall mount bracket, and screw in 4 M8 nuts for mounting the bracket. 3. Take off the housing from the packing, and take off the baseboard (4 bolts on it.) inside the housing. Thread the cable through the top of the housing. Fix the housing on the wall...

Page 23 - GLOVE

2-22 5. Align the two screw holes on the bottom of mechanical part to the two bolts on the base of the housing, and twist the mechanical part clockwise a little bit in order to engage it with the base. Screw the two bolts on the base, and then connect and fix the connection bus to the PCB board on t...

Page 24 - installing the bulb.

2-23 Notice: In order to protect the bulb from dirt and scrape, please put on the gloves before installing the bulb. 7. Turn on the power, and start to operate the EPTZ900. Note: When turning on the power, the EPTZ900 will enter self-inspection mode, and carry out a self-testing program. After finis...

Page 25 - Cut the ceiling

2-24 2.4.3. EPTZ500 Dome Camera Installation 1. Take off the housing from the packing, and take off he PCB board (4 bolts on it) inside the housing. 2. Cut the ceiling against the housing’s shape with a saw. 3. Thread the cable through the screw and the hole on the top of the housing, and tighten up...

Page 27 - Connection wire

2-26 GLOVE Connection wire Button Button Notice: In order to protect the bulb from dirt and scrape, please put on the gloves before installing the bulb. 8. Turn on the power, and start to operate the EPTZ500.

Page 29 - Option

3-28 3. EPTZ900/500 CAMERA SETUP MENU In this section, setup and operation guide of EPTZ900/500 will be introduced. There are 22 items of the setting menu. However, there is only one line on the line display, so using some combination keys to operate is necessary. 3.1. Structure of the Setup Menu Pr...

Page 34 - Two point auto pan; Press Shift + A.Pan to enter the 360° auto pan. The camera will; Focus on a preset position:; Press the number key, and then press Position to

4-33 4. EPTZ900/500 FUNCTION SETUP AND OPERATION 4.1. Manual Control Mode ¾ Manual control: Shift Joystick Up/Down/Left/Right, and turn it Clockwise/Counterclockwise to control speed dome. Use the control keys which are Zoom, Focus and IRIS function keys on the keyboard to zoom In/Out, focus N (near...

Page 42 - EverFocus Electronics Corp.; 801 Highland Ave. Unit A

4-41 EverFocus Electronics Corp. Head Office: 12F, No.79 Sec. 1 Shin-Tai Wu Road, Hsi-Chih, Taipei, Taiwan TEL: +886-2-26982334 FAX: +886-2-26982380 www.everfocus.com.tw USA Office: 1801 Highland Ave. Unit A Duarte, CA 91010, U.S.A. TEL: +1-626-844-8888 FAX: +1-626-844-8838 www.everfocus.com Europea...