Edelbrock 70410 - Manuals - manualsarea.com

Page 3 - Use only Teflon Paste.

©2007 Edelbrock CorporationBrochure #63-0478 Catalog #70410 Rev. 7/07 - DC/mc Page 3 of 16 Caution!! Please read this installation manual fully before installing this system. You will need to have available the following tools: Hand Tools: ❑ Socket set including ratchets and extensions ❑ Screwdriver...

Page 4 - These tests were conducted with 950psi nitrous bottle pressure.; Never exceed the recommended jetting!; Most aftermarket; performance chips; Nitrous Jetting

Catalog #70410 Rev. 7/07 - DC/mc ©2007 Edelbrock CorporationBrochure #63-0478 Page 4 of 16 1.0 Introduction to your Edelbrock 2005-2007 Mustang GT Nitrous System 1.1 General Information The Edelbrock Performer Nitrous System (Part Number 70410) is designed for the stock to slightly modified2005 to 2...

Page 5 - Performer Kit Bill of Materials; Description Item #

©2007 Edelbrock CorporationBrochure #63-0478 Catalog #70410 Rev. 7/07 - DC/mc Page 5 of 16 1.4 Performer Kit Bill of Materials Qty. Description Item # ❑ 1 2005-07 Mustang Nitrous Plate 1 ❑ 1 Gasket 2 ❑ 2 4AN x 1/8”NPT Straight Fitting, Red 3 ❑ 1 4AN x 1/8”NPT Nitrous Filter Fitting 4 ❑ 1 3AN x 1/8”N...

Page 6 - inside the bottle or the bottle valve itself.; Racing Vehicles

©2007 Edelbrock CorporationBrochure #63-0478 Catalog #70410 Rev. 7/07 - DC/mc Page 6 of 16 2.0 Nitrous System Installation 2.1 Nitrous Bottle Mounting The nitrous bottle is an aluminum cylinder, designed and manufactured to withstand very high pressures. The valve ontop of the bottle is a high-flow ...

Page 8 - Nitrous Feed Line Mounting; Attach nitrous supply line to bottle.; Solenoid Assembly and Installation

©2007 Edelbrock CorporationBrochure #63-0478 Catalog #70410 Rev. 7/07 - DC/mc Page 8 of 16 2.4 Nitrous Feed Line Mounting 1. Determine the route your main nitrous feed line will follow. Ensure the path does not route the nitrous feed line tooclose to the exhaust system, suspension, electrical lines/...

Page 9 - Nitrous Plate Installation; Remove the two studs from the intake manifold.; Fuel Pressure Take-Off Adapter Installation; Disconnect the connector for the fuel rail pressure sensor.

©2007 Edelbrock CorporationBrochure #63-0478 Catalog #70410 Rev. 7/07 - DC/mc Page 9 of 16 2.6 Nitrous Plate Installation 1. Disconnect the throttle body from the intake manifold by removing the two nuts from the studs on the lower portionof the throttle body and removing the two bolts from the uppe...

Page 10 - Electrical System Installation; Nitrous Electrical Components Bill of Materials (BOM)

©2007 Edelbrock CorporationBrochure #63-0478 Catalog #70410 Rev. 7/07 - DC/mc Page 10 of 16 3.0 Electrical System Installation 1 2 3 4 5 6 7 8 9 10 11 12 13 14-16 3.1 Nitrous Electrical Components Bill of Materials (BOM) Important: The wiring hardware and instructions included with this kit are inte...

Page 11 - Wide Open Throttle

©2007 Edelbrock CorporationBrochure #63-0478 Catalog #70410 Rev. 7/07 - DC/mc Page 11 of 16 Wire Color Red Yellow BlueBlue BlackBlackBlack Tan/Yellow System Main System Power Solenoid Power TPS 5 Volt InputTPS 5 Volt Input WOT Module Ground Solenoid Ground Solenoid Power In TPS 5 Volt Reference Orig...

Page 12 - Wiring; recommend using an existing ground used by the OEM.; Arming Switch and Installation; for further information.; Final Solenoid and WOT Module Installation Recommendations; wires from shorting out.

©2007 Edelbrock CorporationBrochure #63-0478 Catalog #70410 Rev. 7/07 - DC/mc Page 12 of 16 3.5 Wiring 1. Verify that the battery is disconnected. If it is not, remove the ground strap and place it away from the battery to keep it from shorting out. 2. Locate the red wire with fuse holder and affix ...

Page 13 - Before You Run Your Vehicle Using Your Edelbrock Nitrous System; Fuel System Check; Solenoid Inspection and Maintenance; Do not open pressurized fuel lines over a hot engine.

©2007 Edelbrock CorporationBrochure #63-0478 Catalog #70410 Rev. 7/07 - DC/mc Page 13 of 16 4.0 Before You Run Your Vehicle Using Your Edelbrock Nitrous System You have just completed the installation of your Edelbrock Nitrous System. It is time to perform some basic system checks toensure all of th...

Page 14 - Troubleshooting Your Edelbrock Nitrous System; How to use our Troubleshooting Flowchart:; Symptom #3... Engine runs excessively rich when system is activated.

©2007 Edelbrock CorporationBrochure #63-0478 Catalog #70410 Rev. 7/07 - DC/mc Page 14 of 16 6.0 Troubleshooting Your Edelbrock Nitrous System How to use our Troubleshooting Flowchart: The troubleshooting of a nitrous system is basic and straightforward. The symptom chart is divided by symptom, cause...

Page 15 - Clean or replace filter.; Symptom #6... No change in performance when system is activated.

©2007 Edelbrock CorporationBrochure #63-0478 Catalog #70410 Rev. 7/07 - DC/mc Page 15 of 16 Symptom #5… Engine detonates heavily when system is activated. Inadequate fuel delivery due to: 1. Plugged fuel filter.a. Inspect fuel filter. i. Clean or replace filter. 2. Crimped fuel line.a. Inspect fuel ...

Page 16 - Edelbrock Corporation

©2007 Edelbrock CorporationBrochure #63-0478 Catalog #70410 Rev. 7/07 - DC/mc Page 16 of 16 Symptom #6… No change in performance when system is activated (Continuation) 9. Loose nitrous solenoid wiring.a. Inspect solenoid wiring. See “Electrical System Installation” section. b. Consult a book concer...