Dynacord DTI 2000 - Manuals

Page 2 - Contents

DTI 2000 Manual e EDITED.doc 2 Contents *** Inhaltsverzeichnis Introduction This owner’s manual covers the installation, programming, and operation of DYNACORD’s DTI 2000 Digital Telephone Interface. Since operating and programming the DTI 2000 is similar to the operation and programming of a paging...

Page 3 - Controls and Connections; indicator

DTI 2000 Manual e EDITED.doc 3 Controls and Connections front view 1. POWER indicator The POWER LED lights when the DTI 2000 receives power input from the supplied power supply unit, which allows worldwide connection and use because it accepts input voltages between 85V AC and 250V AC. 2. SEIZE / DR...

Page 4 - TO PAGING MANAGER connectors, female

DTI 2000 Manual e EDITED.doc 4 Rear 6. TO PAGING MANAGER connectors, female The two TO PAGING MANAGER connectors represent the interface to the DPM 4000 System Manager. Using either the 9-pole D-Sub connector or the 6-pole RJ-12 socket (simultaneous use of both terminals is not possible) to establis...

Page 5 - Se Up and Connections; The DTI 2000 package contains the following parts:

DTI 2000 Manual e EDITED.doc 5 Se Up and Connections 1. Unpacking The DTI 2000 package contains the following parts: 1 DTI 2000 Digital Telephone Interface 1 power supply unit, 100 – 240V AC 1 IEC mains cord 1 interface cable for DPM 4000 connection, RJ-12 to RJ-45 1 telephone cable, RJ-11 to TAE 1 ...

Page 6 - Switches 3 – 8 are not used and should be left in their OFF-position.

DTI 2000 Manual e EDITED.doc 6 2.2 Internal DIP switches (S202 and S203) To make any changes to the internal DIP-switch settings, you first have to remove the cover plate by loosening/removing the screws on the rear panel, as indicated in the diagram below. Slightly lift the cover plate at the rear ...

Page 7 - Switches 5 – 8 are not in use and should be left in their OFF-position.

DTI 2000 Manual e EDITED.doc 7 than the specified maximum connection timeout setting allows. If the caller does not enter any new selection during the connection timeout, the DTI 2000 automatically finishes the momentary announcement and releases the PA-system. Afterwards, the telephone connection i...

Page 8 - Connecting Phone Lines or a Telephone set

DTI 2000 Manual e EDITED.doc 8 Use one of the TO PAGING MANAGER sockets (not both simultaneously) for connecting the DTI 2000 to the DPM 4000. The DTI 2000 needs to be connected to a paging console input (DPC IN, RJ-45 socket) of the DPM 4000 using the supplied, 3.5m long interface cable (RJ-12 to R...

Page 9 - settings

DTI 2000 Manual e EDITED.doc 9 6. Country settings Different countries and regions have different telephone standards, which may differ in e.g. signal level and dial tones. The DTI 2000 can be and should be configured to meet those individual requirements. Not doing so can result in faulty operation...

Page 10 - Entry

DTI 2000 Manual e EDITED.doc 10 accepts the call and establishes a connection. First, you will hear a short noise (DTI 2000 line test) followed by different tone signals, which indicate that the DTI 2000 expects further entries. 2. Password Entry The DTI 2000 answers an incoming phone call with diff...

Page 12 - Clears the actual zone or group selection.

DTI 2000 Manual e EDITED.doc 12 2000 is recommended, because this is the only way to gain access to the total amount of 100 call numbers (accordingly to 100 paging console keys). Connect a DPC 4550 + DPC 4530 to the corresponding input at the DPM 4000 in the PC Designer Software, give it a meaningfu...

Page 13 - DTI 2000 Operation Example

DTI 2000 Manual e EDITED.doc 13 60 TALK All groups 9 Starts an announcement in all zones with priority 9 … … … … … 70 MACRO Nr. 15 0 Triggers macro No. 15 71 MACRO Nr. 16 0 Triggers macro No. 16 … … … … … 99 CLEAR 0 0 Clears the actual zone / group selection 0 (or 00) STOP 0 5 Stops audio signals wi...

Page 14 - Test Functions; DROP LED; Specifications

DTI 2000 Manual e EDITED.doc 14 Test Functions The processor system automatically runs an initial self-test whenever the DTI 2000 is connected to the mains. During this procedure, first the red DROP LED should light. Afterwards, the orange TALK LED blinks for approximately 3 seconds. In case faulty ...