Dual XPE4700 - Manuals - manualsarea.com

Page 2 - Preparation; Before You Start; Mounting Location; TYPICAL MOUNTING METHOD

2 XPE SERIES INSTALLATION Preparation Please read entire manual before installation. Due to the technical nature of amplifiers, it is highly recommended that your DUAL amplifier is installed by a professional installer or an authorized dealer. Before You Start • Disconnect negative battery termina...

Page 3 - Speaker Wires; Input Signal; XPE SERIES; Connection Descriptions

NOTEBe sure to follow specific instructions included with your amplifier installation kit(not included with this amplifier). The information below should be used a general guideline only. Power Wire (+12V) • Disconnect negative battery terminal before proceeding. Consult a qualified technician for i...

Page 4 - Audio Inputs and Controls

4 XPE SERIES INSTALLATION X P E 1 7 0 0 L I N E I N P U T S L E F T R I G H T G A I N M I N M A X L P O F F F R E Q U E N C Y 5 0 H z 5 0 0 H z X - O V E R B A S S B O O S T 0 F F 6 d B 1 2 d B P H A S E 0 1 8 0 S U B S O N I C 0 F F O N Audio Inputs and Controls S P E A K E R I N P U T S L I N E I...

Page 5 - Power and Speaker Connections

Power and Speaker Connections Ground Connection Remote Connection +12VDC Battery Connection 123 Fuse(s) Speaker Connection(s) 45 5 XPE SERIES INSTALLATION 3 0 A F U S E S 3 0 A X P E 1 7 0 0 S P E A K E R + - G N D R E M B A T + P O W E R 2 5 A F U S E X P E 2 7 0 0 G N D R E M B A T + P O W E R S ...

Page 6 - Fuse Rating; Power/Ground Wire Size; Main Power Connections; Typical Wire Routing

6 XPE SERIES INSTALLATION REM (TURN-ON LEAD) Fuse Rating When replacing fuses, make sure new fuse is the correct type and amperage. Using an incorrect fuse could damage the amplifier. XPE1700 30 amp ATO x 2 XPE2700 30 amp ATO x 1 XPE4700 25 amp ATO x 2 Power/Ground Wire Size For optimum performance...

Page 7 - Amplifier Connections; Speaker Connections; Input Signal Connections; Typical Bridged Wiring

7 XPE SERIES INSTALLATION Amplifier Connections Speaker Connections Connect speaker wires observing polarity. The minimum impedance load for the XPE2700 and XPE4700 is 2 ohms stereo and 4 ohms bridged. Use of loads lower than these is not recommended and may cause amplifier damage. The XPE2700 and ...

Page 9 - Limited One-Year Warranty

9 XPE SERIES WARRANTY Limited One-Year Warranty This warranty gives you specific legal rights. You may also have other rights which vary from state to state. Dual Electronics Corp. warrants this product to the original purchaser to be free from defects in material and workmanship for a period of o...

Page 10 - Specifications; CEA-2006 Power Standard Specifications

10 XPE SERIES OPERATION Specifications CEA-2006 Power Standard Specifications (reference: 14.4VDC, 20Hz~20kHz) Power Out put (14.4VDC, 20Hz ~ 20kHz): 240 Watts RMS x 1 channel @ 4 ohms and ≤ 1% THD+N 400 Watts RMS x 1 channel @ 2 ohms and ≤ 1% THD+N Total dynamic power: 1000 Watts Sign...

Page 11 - Notes

Page 12 - Troubleshooting

Dual Electronics Corp. Toll Free: 1-866-382-5476 www.dualav.com ©2010 Dual Electronics Corp. NSA0610-V01 XPE SERIES OPERATION Troubleshooting Problem Cause Action Unit will not turn on (no power LED indicator) +12V wire not connected or incorrect voltage REM wire not connected or incorrect voltage ...