Directed Electronics 369D - Manuals

5 © 2 0 0 3 d i r e c t e d e l e c t r o n i c s , i n c . your warranty Your warranty registration must be completely filled out and returned within 10 days of purchase. Your product warranty will not be validated if your warranty registration is not returned. Please note that it is necessary to k...

10 © 2 0 0 3 d i r e c t e d e l e c t r o n i c s , i n c . iin nsstta alllla attiio on n Be sure to read this section thoroughly and view the Rattler Do- It-Yourself Installation Video in its entirety before starting the installation. Pay special attention to all warnings to prevent personal injur...

11 © 2 0 0 3 d i r e c t e d e l e c t r o n i c s , i n c . step 1 Ground Wire The BLACK wire on the main 8-pin harness is ground. This wire should be connected to a clean, paint-free area of metal in the drivers kick panel area. First strip back a ¾-inch section of the insulation off the BLACK wir...

12 © 2 0 0 3 d i r e c t e d e l e c t r o n i c s , i n c . step 2 Constant Power and Ignition wires Almost all power and ignition wires can be found behind the key cylinder under the lower drivers side dash panel. Using the appropriate hand tools, remove the lower dash panel using care not to brea...

13 © 2 0 0 3 d i r e c t e d e l e c t r o n i c s , i n c . Once the constant power wire has been identified, solder the two thick RED wires from the control module to it and cover the connection with electrical tape to ensure a safe connection. With the meter black lead still in the kick panel, lo...

14 © 2 0 0 3 d i r e c t e d e l e c t r o n i c s , i n c . If the vehicle requires more than one ignition as per the Web site information follow the same test procedure and solder the thick PINK/WHITE wire to it and be sure to cover your connection with electrical tape. If your vehicle requires mo...

15 © 2 0 0 3 d i r e c t e d e l e c t r o n i c s , i n c . Now that the accessories have been located, find the wire suspected to be the starter wire according to the web information on your vehicle. Place the red lead of your meter on the wire. With the key in the off position the meter should re...

16 © 2 0 0 3 d i r e c t e d e l e c t r o n i c s , i n c . and neutral safety wires. First locate the factory brake wire using your multi-meter. Find the switch at the top of the metal arm coming off the brake pedal. There are usually two wires connected to that switch. Locate the wire color accor...

18 © 2 0 0 3 d i r e c t e d e l e c t r o n i c s , i n c . The after-market safety switch will have two wires coming off it. Take one of the wires (it does not matter which one) and strip back a ¾-inch section of the insulation off the wire. Crimp a ring terminal to the wire, and using a self tapp...

19 © 2 0 0 3 d i r e c t e d e l e c t r o n i c s , i n c . BLACK/WHITE wire on the secondary connector and cover theconnection with electrical tape. The shut down toggle switch is designed to shut the remote start off in an emergency or to disable the remote start functions temporarily (i.e., for ...

20 © 2 0 0 3 d i r e c t e d e l e c t r o n i c s , i n c . Using the web information on the vehicle, locate the suspected wire and place the red lead of the meter to a constant (+)12 volt source and secure it. Place the multi-meter in the DC position. Using the black lead of the meter, probe the w...

22 © 2 0 0 3 d i r e c t e d e l e c t r o n i c s , i n c . Once the correct wire has been found, solder the small LIGHT GREEN wire off the main connector to it and cover the connec- tion with electrical tape. Repeat this process for the unlock wire but press the switch tothe unlock position when t...

23 © 2 0 0 3 d i r e c t e d e l e c t r o n i c s , i n c . The Rattler Do-It-Yourself system comes with a dual-relay packincluded for door lock operation. To interface this piece with thesystem it is necessary to cut the three-pin plug off the relaymodule leaving the three wires long enough to con...

24 © 2 0 0 3 d i r e c t e d e l e c t r o n i c s , i n c . If the idle is too slow or too high, the system will shut down the engine to prevent damage. If the starter does not crank long enough to actually start the engine, it is possible to change the programming to extend the crank time. Refer t...

26 © 2 0 0 3 d i r e c t e d e l e c t r o n i c s , i n c . step 8 Factory Alarm Arm or Disarm Since most newer vehicles come equipped with a factory alarm system, it is necessary for the factory alarm to be armed/disarmed when unlocking the doors and disarmed while remote starting the vehicle. Loc...

27 © 2 0 0 3 d i r e c t e d e l e c t r o n i c s , i n c . When the correct wire has been found, solder the small GREEN/BLACK wire to the wire which activates in the unlock position when the key is turned. Connect the GREEN/WHITE wire to the wire which activates in the lock position when the key i...

28 © 2 0 0 3 d i r e c t e d e l e c t r o n i c s , i n c . To determine what bypass module your vehicle requires, check your web vehicle information sheet. step 10 Mounting the receiver/antenna The best location for the receiver/antenna is centered high on either the front or rear windshield. For ...

29 © 2 0 0 3 d i r e c t e d e l e c t r o n i c s , i n c . step 11 Testing the system Once steps 1-9 have been completed, the operation of the system can be tested. Place the two 30-amp fuses back into the relay satellite red wire fuse holders. Make sure that the vehicle is in park with the emer- ...

31 © 2 0 0 3 d i r e c t e d e l e c t r o n i c s , i n c . button two Channel 2 button three Remote Start + buttons one and two Timer mode + button one and three Short-Run/Turbo 3. T Trraan nssm miitt. While holding the Program switch, press the button on the transmitter that you would like to con...

35 © 2 0 0 3 d i r e c t e d e l e c t r o n i c s , i n c . ffe ea attu urre ess m me en nu u The factory settings are indicated in bold text in the table below. note: The number in parentheses indicate the number of times the LED will flash. Feature L LE ED D O On n SSeettttiin ngg LED Off Setting...

41 © 2 0 0 3 d i r e c t e d e l e c t r o n i c s , i n c . authorized dealer. Unless otherwise specified, the buttons used in all of the instructions in this manual correspond to a Standard Configuration transmitter. standard configuration B Bu uttttoon n The door locking and unlocking functions a...

42 © 2 0 0 3 d i r e c t e d e l e c t r o n i c s , i n c . u ussiin ng g yyo ou urr ssyysstte em m warning! safety first The following safety warnings must be observed at all times: ■ When properly installed, this system can start the vehicle via a command signal from the remote control transmitte...

44 © 2 0 0 3 d i r e c t e d e l e c t r o n i c s , i n c . ELECTRONICS, INC.WILL NOT BE HELD RESPON- SIBLE OR PAY FOR INSTALLATION OR REINSTALLA- TION COSTS. locking Pressing for one second will lock the doors. The parking lights will flash once to confirm that the doors are locked. unlocking To u...

45 © 2 0 0 3 d i r e c t e d e l e c t r o n i c s , i n c . remote start This feature allows you to remotely start and run your vehicle for a programmable period of time. This makes it possible to warm up the engine, as well as adjust the interior temperature of the vehicle with the climate control...

47 © 2 0 0 3 d i r e c t e d e l e c t r o n i c s , i n c . 3. Press and release the and buttons at the same time. 4. The lights will flash to indicate the remote start has entered short run turbo mode. 5. Turn off the key, the engine will keep running. 6. Exit and secure the vehicle. 7. The engine...

48 © 2 0 0 3 d i r e c t e d e l e c t r o n i c s , i n c . 5. The system will start every 3 hours until canceled by the brake, hood, or neutral safety shut-down wires. To exit timer mode, turn the ignition switch on any time the engine is not running. The parking lights will flash 4 times, indi- c...

55 © 2 0 0 3 d i r e c t e d e l e c t r o n i c s , i n c . n no otte ess _________________________________________________ _________________________________________________ _________________________________________________ _________________________________________________ _________________________...

Cut along dotted line and f old f or a quick and eas y r efer ence to k eep in y our pur se or w allet. ✂ ✂ QUICK REFERENCE GUIDE: To lock the doors using your remote ■ Pressing / for one second will lock the doors. The parking lights will flash once to confirm the doors are locked. To unlock the do...

The company behind this system is Directed Electronics, Inc. Since its inception, Directed Electronics has had one purpose, to provide consumers withthe finest vehicle security and car stereo products and accessories available. The recipient ofnearly 100 patents and Innovations Awards in the field o...