Devilbiss A05982 - Manuals - manualsarea.com

Page 2 - TABLE OF CONTENTS

2 Date of Manufacture: ___________________________ Fecha de fabricación:, Date de fabrication: Serial No: ______________________________________ Número de serie:, Nombre d'ordre TABLE OF CONTENTS SAFETY GUIDELINES AND INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . .3 GENERAL SAFETY RULES...

Page 3 - SAFETY GUIDELINES / DEFINITIONS; SAVE THESE INSTRUCTIONS!; IMPORTANT SAFETY INSTRUCTIONS

3 indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. indicates a potentially hazardous situation which, if not avoided, may result in mi...

Page 4 - GENERAL SAFETY RULES

4 Fig. 6 Fig. 5 Fig. 2 Fig. 3 Fig. 4 1. Read and understand tool labels andmanual. Failure to follow warnings could result in DEATH or SERIOUS INJURY . Fig. 1. 2 . Operator and others in work area MUST wear safety glasses with side shields. These safety glasses must conform to ANSIZ87.1 requirements...

Page 7 - magazine from the side.; POWER SOURCE; The tool is equipped with a; EMPLOYER’S RESPONSIBILITIES

7 Employer must enforce compliance with the safety warnings and all otherinstructions contained in this manual. Keep this manual available for use by all people assigned to use this tool. For personal safety and proper operation of this tool, read and understandtool labels and manual. Failure to fol...

Page 8 - Insert a strip of fasteners into the side of the magazine, with; PREPARING THE TOOL

8 Fig. 19 Fig. 18 Fig. 21 Fig. 22 A Fig. 20 1. After reading and understanding this entire manual, connect tool to air supply (Fig. 18). 2. Depress latch and slide magazine cover open (Fig. 19). 3. Insert a strip of fasteners into the side of the magazine, with points down, in contact with the botto...

Page 9 - USING THE TOOL; “single sequential actuation”; RUBBER NOSE CUSHION; OPERATING INSTRUCTIONS

9 USING THE TOOL Complete all steps of PREPARING THE TOOL before using the tool. This tool is shipped from the factory with a “single sequential actuation” trigger. This actuation design requires the release of both the trigger andsafety mechanism after each fastener is driven. Sequential actuation ...

Page 10 - CLEAN AND INSPECT DAILY; D i s c o n n e c t t o o l f r o m a i r s u p p l y b e f o r e c l e a n i n g a n d; CLEARING A JAMMED FASTENER; Disconnect tool from air supply.; the quick release latch and open the fastener guide plate; Depress; the quick release latch and close the fastener guide plate.; MAINTENANCE

10 CLEAN AND INSPECT DAILY D i s c o n n e c t t o o l f r o m a i r s u p p l y b e f o r e c l e a n i n g a n d inspection. Correct all problems before placing the tool back in use. Wipe tool clean and inspect for wear or damage. Use non-flammablecleaning solutions to wipe exterior of tool only i...

Page 11 - SERVICE; SERVICE AND REPAIRS; for a list of service centers or call the Customer Care; TROUBLESHOOTING GUIDE

11 SERVICE SERVICE AND REPAIRS All quality tools will eventually require servicing or replacement of parts dueto wear from normal use. For assistance with your tool, visit our website at www.devap.com for a list of service centers or call the Customer Care Department at 1-800-888-2468. All repairs m...

Page 12 - WARRANTY

WARRANTY DeVilbiss Air Power Company warrants to the original purchaser who uses the product in a consumer application (personal, residential or household usage) that all products covered under this warranty arefree from defects in material and workmanship for one year from the date of purchase. All...