Page 2 - Specifications; Voltage Class
English- 2 Specifications Voltage Class 115V Class Model Number VFD-XXXE 002 004 007 Max. Applicable Motor Output (kW) 0.2 0.4 0.75 Max. Applicable Motor Output (hp) 0.25 0.5 1.0 Rated Output Capacity (kVA) 0.6 1.0 1.6 Rated Output Current (A) 1.6 2.5 4.2 Maximum Output Voltage (V) 3-Phase Proportio...
Page 3 - General Specifications
English- 3 General Specifications Control System SPWM(Sinusoidal Pulse Width Modulation) control (V/f or sensorless vector control) Frequency Setting Resolution 0.01Hz Output Frequency Resolution 0.01Hz Torque Characteristics Including the auto-torque/auto-slip compensation; starting torque can be 1...
Page 4 - I M
English- 4 Storage/ Transportation Temperature -20 o C to 60 o C Ambient Humidity Below 90% RH (non-condensing) Vibration 9.80665m/s 2 (1G) less than 20Hz, 5.88m/s2 (0.6G) at 20 to 50Hz Approvals Basic Wiring Diagram Users must connect wiring according to the following circuit diagram shown below. A...
Page 5 - t yp e a n d ap p li ca ti on; B ra ke un it; t yp e a n d a p p lic a tio n; BR; Figure 4 Wiring for NPN Mode and PNP Mode
English- 5 + - P le a se u se b r a ke u n it a n d / o r b ra ke re si st or d e p e n d in g o n t yp e a n d ap p li ca ti on B ra ke un it ( op tio na l) B U E B R b ra ke re sis to r(o p ti on a l) F ig ur e 1 f or mo de l s o f V FD - E S e r i e sV F D0 0 2 E 1 1A / 2 1 A /2 3 A , V F D 0 04 ...
Page 6 - PIN; communication
English- 6 C. PNP mode without external power D. PNP mode with external power Sw1 Factory setting N P N P N P Sw1 Factory setting N P N P N P 2 4Vdc - + Figure 5 RJ-45 Pins Definition for VFD*E*C Models PIN Signal Description 1 CAN_H CAN_H bus line (dominant high) 2 CAN_L CAN_L bus line (dominant lo...
Page 7 - Operation Steps of the Digital Keypad; To s h if t d a ta; Set t in g PL C Mo de; Set t in g p aram et er s
English- 7 Operation Steps of the Digital Keypad To s h if t d a ta Set t in g PL C Mo de Set t in g Mo d e Set t in g d irec t io n (W he n operat ion s our ce is digit al keypa d) STA RT GO STA RT enter PL C2 mode enter PL C1 mode N OTE : In t he p ara meter se tt i ng mod e, you can pr es s t o r...
Page 8 - Power Terminals and Control Terminals; Fr ame A; Terminal Explanations; AC drive output terminals for connecting 3-phase induction motor
English- 8 Power Terminals and Control Terminals Fr ame A Fr ame B Fr ame C Frame Power Terminals Torque Wire Wire Type R/L1, S/L2, T/L3 A U/T1, V/T2, W/T3, 14kgf-cm (12in-lbf) 12-14 AWG. (3.3-2.1mm 2 ) Copper only, 75 o C R/L1, S/L2, T/L3 U/T1, V/T2, W/T3 B +/B1, B2, -, 18kgf-cm (15.6in-lbf) 8-18 A...
Page 9 - The Specification for the Control Terminals; 0 V; The position of the c ontr ol ter minals; Term in al s 2; Control Terminals Explanations
English- 9 The Specification for the Control Terminals R S - 4 8 5 p o r t 1 0 V M I1 M I2 M I3 M I4 M I5 M I6 DCM 2 4 V DCM ACM AV I A C I AFM MCM MO1 R A R B R C The position of the c ontr ol ter minals Term in al s 2 Term in al s 1 Frame Control Terminals Torque Wire Terminals 1 5 kgf-cm (4.4 in-...
Page 10 - Summary of Parameter Settings
English- 10 Terminal Symbol Terminal Function Factory Settings (NPN mode) ON: Connect to DCM MO1 Multi-function Output 1 (Photocoupler) Maximum 48VDC, 50mA Refer to Pr.03.01 for programming M O1 -DCM M o1 M C M M ax : 4 8 V d c 5 0 mA i n te rn a l c i rcu i t MCM Multi-function output common Common...
Page 14 - Method
English- 14 Pr. Explanation Settings Factory Setting NOTE 01.40 Mid-Point Frequency (Fmid) (Motor 3) 0.10 to 600.0 Hz 1.50 115V/230V series: 0.1V to 255.0V 10.0 01.41 Mid-Point Voltage (Vmid) (Motor 3) 460V series: 0.1V to 510.0V 20.0 01.42 Minimum Output Frequency (Fmin) (Motor 3) 0.10 to 600.0 Hz ...
Page 15 - Line Start Lockout
English- 15 Pr. Explanation Settings Factory Setting NOTE 02.05 Line Start Lockout 0: Disable. Operation status is not changed even if operation command source Pr.02.01 is changed. 1: Enable. Operation status is not changed even if operation command source Pr.02.01 is changed. 2: Disable. Operation ...
Page 18 - Input
English- 18 Pr. Explanation Settings Factory Setting NOTE 04.03 Keypad Potentiometer Negative Bias, Reverse Motion Enable/Disable 0: No negative bias command 1: Negative bias: REV motion enabled 0 04.04 2-wire/3-wire Operation Control Modes 0: 2-wire: FWD/STOP, REV/STOP 1: 2-wire: FWD/REV, RUN/STOP ...
Page 21 - Most
English- 21 Pr. Explanation Settings Factory Setting NOTE 06.03 Over-Torque Detection Mode (OL2) 0: Disabled 1: Enabled during constant speed operation. After the over-torque is detected, keep running until OL1 or OL occurs. 2: Enabled during constant speed operation. After the over-torque is detect...
Page 22 - FLA
English- 22 Pr. Explanation Settings Factory Setting NOTE 06.11 Fourth Most Recent Fault Record 06.12 Fifth Most Recent Fault Record 27: DCBUS error (cF3.3) 28: IGBT Overheat (cF3.4) 29: Power Board Overheat (cF3.5) 30: Control Board CPU WRITE failure (cF1.1) 31: Control Board CPU WRITE failure (cF2...
Page 28 - 6: PID supervision
English- 28 Pr. Explanation Settings Factory Setting NOTE 11.00 Multi-function Output Terminal MO2/RA2 0 11.01 Multi-function Output Terminal MO3/RA3 0 11.02 Multi-function Output Terminal MO4/RA4 0: No function 1: AC drive operational 2: Master frequency attained 3: Zero speed 4: Over torque detect...
Page 30 - Fault Codes
English- 30 Pr. Explanation Settings Factory Setting NOTE 12.18 Max. ACI3 Input Current 0.0 to 20.0mA 20.0 12.19 Max. ACI3 Scale Percentage 0.0 to 100.0% 100.0 12.20 AO1 Terminal Analog Signal Mode 0: AVO1 1: ACO1 (analog current 0.0 to 20.0mA) 2: ACO1 (analog current 4.0 to 20.0mA) 0 0: Analog Freq...
Page 35 - Frame; N OT E
English- 35 N OT E Frame A (A1): VFD002E11A/21A/23A, VFD004E11A/21A/23A/43A, VFD007E21A/23A/43A, VFD015E23A/43A, VFD002E11C/21C/23C, VFD004E11C/21C/23C/43C, VFD007E21C/23C/43C, VFD015E23C/43C, VFD002E11T/21T/23T, VFD004E11T/21T/23T/43T, VFD007E21T/23T/43T, VFD015E23T/43T Frame A (A2): VFD002E11P/21P...
Page 36 - Frame C
English- 36 Frame C H H1 W1 W S1 S2 D D1 D2 Unit: mm [inch] Frame W W1 H H1 D D1 D2 S1 S2 C1 130.0 [5.12] 116.0 [4.57] 260.0 [10.24] 246.5[9.70] 169.2[6.66] 78.5 [3.09] 8.0 [0.31] 6.5 [0.26] 5.5 [0.22] N OT E Frame C (C1): VFD055E23A/43A, VFD075E23A/43A, VFD110E43A/43C, VFD055E23C/43C, VFD075E23C/43...