Delta SS350LS - Manuals - manualsarea.com

Page 2 - SAFETY GUIDELINES - DEFINITIONS; GENERAL SAFETY RULES

2 Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, may result in mi...

Page 4 - SAVE THESE INSTRUCTIONS.

4 FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL INJURY. ADDITIONAL SAFETY RULES FOR SCROLL SAWS SAVE THESE INSTRUCTIONS. Refer to them often and use them to instruct others. 1. DO NOT OPERATE THIS MACHINE until it is assembled and installed according to the instructions. 2. OBTAIN ADV...

Page 5 - POWER CONNECTIONS

5 A separate electrical circuit should be used for your machines. This circuit should not be less than #12 wire and shouldbe protected with a 20 Amp time lag fuse. If an extension cord is used, use only 3-wire extension cords which have 3-prong grounding type plugs and matching receptacle which will...

Page 6 - EXTENSION CORDS; FOREWORD; FUNCTIONAL DESCRIPTION; UNPACKING AND CLEANING; NOTICE: THE MANUAL COVER PHOTO ILLUSTRATES THE CURRENT

6 EXTENSION CORDS FOREWORD Delta ShopMaster Models SS350 and SS350LS 16" Scroll Saws are designed to give high quality, smooth cuttingperformance with capacity to cut up to 16" wide by 2" thick woodworking materials and have a 3/4" stroke. DeltaShopMaster Models SS350 and SS350LS com...

Page 7 - CARTON CONTENTS

7 CARTON CONTENTS Fig. 1 1. Scroll Saw FOR MODEL SS350LS ONLY 2. Stand Leg (3)3. Lower Side Brace 30" Long (2)4. Upper Side Brace 22½" Long (2)5. Lower Back Brace 18½" Long (1) 1 2 3 4 5 6 7 MODEL SS350LS ONLY MODEL SS350LS ONLY 8 9 10 11 12 13 6. Upper Back Brace 12" Long (1)7. Stan...

Page 8 - ASSEMBLY; STAND

8 ASSEMBLY FOR YOUR OWN SAFETY, DO NOT CONNECT THE MACHINE TO THE POWER SOURCE UNTIL T H E M A C H I N E I S C O M P L E T E LY A S S E M B L E D A N D Y O U R E A D A N D U N D E R S TA N D T H E E N T I R EINSTRUCTION MANUAL. STAND (FOR MODEL SS350LS ONLY) NOTE: THE ASSEMBLY OF THIS STAND WILL USE...

Page 9 - OPERATING CONTROLS AND ADJUSTMENTS

9 FASTENING SCROLL SAWTO SUPPORTING SURFACE This scroll saw MUST be securely fastened to a stand or workbench using the three holes, two of which areshown at (A) Fig. 4. The third hole is at the rear of themachine. An alternate method of securing the scroll saw to a sup-porting surface is to fasten ...

Page 13 - TABLE INSERT

13 TABLE INSERT DISCONNECT MACHINE FROM POWERSOURCE. The table insert (A) can be positioned in the saw table withthe opening in the insert pointing to the front of the table,as shown in Fig. 18, or to the right as shown in Fig. 19. With the table in the level position, 90° to the blade, theinsert (A...

Page 14 - OPERATIONS; FOLLOWING A LINE; TROUBLE SHOOTING; CHOICE OF BLADE AND SPEED

14 OPERATIONS FOLLOWING A LINE With your scroll saw you should be able to perform straight or curved cuts with ease. Most beginners will experienceblade wandering; however, they eventually learn to control it as they become more familiar with the machine. Use scrapmaterial to practice cuts before st...

Page 15 - MAINTENANCE; CHANGING BLADES

15 MAINTENANCE CHANGING BLADES Fig. 22 B A 2. Push upper blade chuck locking lever (C) Fig. 23, tothe rear as shown. This will release the blade (D) fromthe upper chuck (E). Fig. 23 E C D 3. Remove the dust collection cup (A) by rotating knob(B) 90° as shown in Fig. 24. Slide dust cup out of theguid...

Page 16 - FUSE REPLACEMENT

16 4. Push lower blade chuck locking lever (F) Fig. 25, tothe rear as shown. This will release the blade (G) fromthe lower chuck (H). Fig. 25 F G H I J L Fig. 26 5. Insert new blade (I) Fig. 26, into the upper bladeholder (J) making certain the blade teeth are pointingdown toward the table. Push upp...

Page 17 - LUBRICATION

17 PARTS, SERVICE OR WARRANTY ASSISTANCE All Delta Machines and accessories are manufactured to high quality standards and are serviced by a networkof Porter-Cable • Delta Factory Service Centers and Delta Authorized Service Stations. To obtain additional information regarding your Delta quality pro...

Page 18 - Two Year Limited New Product Warranty

18 Two Year Limited New Product Warranty Delta will repair or replace, at its expense and at its option, any new Delta machine, machine part, or machine accessorywhich in normal use has proven to be defective in workmanship or material, provided that the customer returns the productprepaid to a Delt...