Delta RTU-DNET - Manuals - manualsarea.com

Page 3 - DeviceNet Remote I/O Communication Module RTU-DNET; DVP-PLC Application Manual; Warning; damages on the device or injuries to staff.; Table of Contents

DeviceNet Remote I/O Communication Module RTU-DNET DVP-PLC Application Manual 1 Warning 3 Please read this instruction carefully before use and follow this instruction to operate the device in order to prevent damages on the device or injuries to staff. 3 Switch off the power before wiring. 3 RTU-DN...

Page 4 - DVP-PLC Application Manual

DeviceNet Remote I/O Communication Module RTU-DNET DVP-PLC Application Manual 2 4.3 DeviceNet I/O Mapping Data .................................................................................................... 14 4.4 Example.............................................................................

Page 5 - Introduction

DeviceNet Remote I/O Communication Module RTU-DNET DVP-PLC Application Manual 3 1 Introduction 1. To ensure correct installation and operation of RTU-DNET, please read this chapter carefully before using your RTU-DNET. 2. This chapter only provides introductory information on RTU-DNET. For more deta...

Page 6 - Extension Modules Connectable to RTU-DNET

DeviceNet Remote I/O Communication Module RTU-DNET DVP-PLC Application Manual 4 Baud rates 125 kbps; 250 kbps; 500 kbps Electrical specification Voltage 11 ~ 25 VDC, supplied by internal bus from PLC MPU Current 28mA (typical), 125mA impulse current (24 VDC) Environment Noise immunity ESD (IEC 6...

Page 7 - Product Profile & Outline; Product Profiles

DeviceNet Remote I/O Communication Module RTU-DNET DVP-PLC Application Manual 5 Default I/O mapping data (DeviceNet → RTU-DNET) I/O mapping data (RTU-DNET → DeviceNet) Special module (model name) Start CR Length (words) Start CR Length (words) DVP-04TC N/A N/A CR#14 4 DVP-04PT N/A N/A CR#18 4 DVP-06...

Page 8 - DeviceNet Connection Port

DeviceNet Remote I/O Communication Module RTU-DNET DVP-PLC Application Manual 6 2.3 DeviceNet Connection Port The connector is used on the connection to DeviceNet. Wire by using the connector enclosed with RTU-DNET. PIN Signal Color Content 1 V- Black 0 VDC 2 CAN_L Blue Signal- 3 SHIELD - Shielded 4...

Page 9 - Basic

DeviceNet Remote I/O Communication Module RTU-DNET DVP-PLC Application Manual 7 OFF When DeviceNet is off, the I/O data in the buffer area will be cleared. IN0 ON When DeviceNet is off, the I/O data in the buffer area will be held. IN1 Reserved Note: z Please set up the function switch when the powe...

Page 10 - Connecting to DeviceNet Connection Port; How to Configure RTU-DNET

DeviceNet Remote I/O Communication Module RTU-DNET DVP-PLC Application Manual 8 3.3 Connecting to DeviceNet Connection Port z The colors on the PINs on the DeviceNet connection port match the colors of the connection cables. Make sure you connect the cable to the right PIN. z We recommend you also a...

Page 11 - Format of Requet Message and Response Message

DeviceNet Remote I/O Communication Module RTU-DNET DVP-PLC Application Manual 9 No. Item Unit Explanation 5 Length of input data of special module Word The length of input data of the special module connected to RTU-DNET 6 Length of output data of special module Word The length of output data of the...

Page 24 - How to Construct a DeviceNet Network Using RTU-DNET; How to Construct DeviceNet by RTU-DNET

DeviceNet Remote I/O Communication Module RTU-DNET DVP-PLC Application Manual 22 5 How to Construct a DeviceNet Network Using RTU-DNET In this section, we will explain how to configure RTU-DNET and the I/O mapping relation between RTU-DNET and DVPDNET-SL by an application example. 5.1 How to Constru...

Page 26 - DeviceNetBuilder will start to scan the entire network.

DeviceNet Remote I/O Communication Module RTU-DNET DVP-PLC Application Manual 24 (6) Click on “OK”, and DeviceNetBuilder will start to scan the entire network. (7) If the bar on the dialog box does not progress, it means the connection between the PC and DVP-SVis abnormal, or there are other program...

Page 34 - Appendix A: DeviceNet Objects RTU-DNET Supports

DeviceNet Remote I/O Communication Module RTU-DNET DVP-PLC Application Manual 32 LED status Indication How to correct voltage 2. Acquire diagnostic information through DeviceNetBuilder. Red light on Fatal error; errors in configuration data Acquire diagnostic information through DeviceNetBuilder. 6....

Page 37 - Appendix B: DeviceNet Objects Defined by RTU-DNET

DeviceNet Remote I/O Communication Module RTU-DNET DVP-PLC Application Manual 35 Common services Implemented for Service code Class Instance Service name 0x05 No Yes Reset 0x0E Yes Yes Get_Attribute_Single 0x10 No Yes Set_Attribute_Single Appendix B: DeviceNet Objects Defined by RTU-DNET Class 0x9...