Delta IPM24S0B0 - Manuals - manualsarea.com

Page 2 - TECHNICAL SPECIFICATIONS; PARAMETER

DS_IPM24S0B0_03202007 2 TECHNICAL SPECIFICATIONS T A = 25°C, airflow rate = 300 LFM, V in = 24Vdc, nominal Vout unless otherwise noted. PARAMETER NOTES and CONDITIONS IPM24S0B0R/S03FA Min. Typ. Max. Units ABSOLUTE MAXIMUM RATINGS Input Voltage (Continuous) 0 40 Vdc Operating Temperature Please refer...

Page 3 - ELECTRICAL CHARACTERISTICS CURVES; Figure 1: Converter efficiency vs. output current; ff

DS_IPM24S0B0_03202007 3 ELECTRICAL CHARACTERISTICS CURVES Figure 1: Converter efficiency vs. output current (3.30V output voltage) Figure 2: Converter efficiency vs. output current (4.0V output voltage) Figure 3: Converter efficiency vs. output current (5.0V output voltage) Figure 4: Converter effic...

Page 5 - application of Vin

DS_IPM24S0B0_03202007 5 ELECTRICAL CHARACTERISTICS CURVES Figure 13: Power on waveform at 12vin, 3.3V/3A out with application of Vin Figure 14: Power on waveform at 12vin, 6.5V/3A out with application of Vin Figure 15: Power off waveform at 12vin, 3.3V/3A out with application of Vin Figure 16: Power...

Page 7 - Note: Input reflected-ripple current is measured with a; Figure 23: Input reflected-ripple current test setup; Vo; GND; F PosCap and 1; Figure 24: Peak-peak output noise and startup transient; setup; Note: All measurements are taken at the module; Ii; DESIGN CONSIDERATIONS; Input Source Impedance; Figure 26: Input ripple voltage for various output models,

DS_IPM24S0 7 B0_03202007 TEST CONFIGURATIONS V I (+) V I (-) BATTERY 2 100uF Electrolytic L TO OSCILLOSCOPE Ceramic 3.3uF Note: Input reflected-ripple current is measured with a simulated source inductance. Current is measured at the input of the module. Figure 23: Input reflected-ripple current tes...

Page 8 - IPM; FEATURES DESCRIPTIONS; Over-Current Protection; The units; Output Voltage Programming; Rtrim is the external resistor in K

DS_IPM24S0B0_03202007 8 DESIGN CONSIDERATIONS Remote On/Off The IPM series power modules have an On/Off control pin for output voltage remote On/Off operation. The On/Off pin is an open collector/drain logic input signal that is referenced to ground. When On/Off control pin is not used, leave the pi...

Page 9 - Figure 29: Trim down Circuit configuration for programming; Table 1 Rtrim is the external resistor in K; P max; Figure 32: Circuit configuration for output voltage margining

DS_IPM24S0B0_03202007 9 FEATURES DESCRIPTIONS (CON.) Figure 28: Trim up Circuit configuration for programming output voltage using an external resistor Rtrim Load Vout Trim GND Figure 29: Trim down Circuit configuration for programming output voltage using an external resistor Figure 30: Circuit con...

Page 10 - THERMAL CONSIDERATIONS; Thermal Testing Setup; Figure 31: Wind tunnel test setup figure dimensions are in

DS_IPM24S0B0_03202007 10 THERMAL CONSIDERATIONS Thermal management is an important part of the system design. To ensure proper, reliable operation, sufficient cooling of the power module is needed over the entire temperature range of the module. Convection cooling is usually the dominant mode of hea...

Page 11 - Figure 33: Output current vs. ambient temperature and air velocity; Figure 36: Output current vs. ambient temperature and air velocity; THERMAL CURVES

DS_IPM24S0B0_03202007 11 IPM24S (Standard) Output Current vs. Ambient Temperature and Air Velocity @ Vin=24V, Vout = 6.5V (Either Orientation) 0 1 2 3 60 65 70 75 80 85 Ambient Temperature ( ℃ ) Output Current(A) Natural Convection 100LFM 200LFM Figure 33: Output current vs. ambient temperature and ...

Page 12 - PICK AND PLACE LOCATION; All dimensions are in millimeters (inches); LEAD FREE PROCESS RECOMMEND TEMP. PROFILE; T e

DS_IPM24S0B0_03202007 12 PICK AND PLACE LOCATION All dimensions are in millimeters (inches) SURFACE- MOUNT TAPE & REEL All dimensions are in millimeters (inches) LEAD FREE PROCESS RECOMMEND TEMP. PROFILE T e T im e 6 0 ~ 1 5 0 se c . A b o v e 2 1 7 0 C 2 0 ~ 4 0 se c . R a m p u p m a x . 3 .0 ...

Page 13 - Mechanical Drawing; SMD PACKAGE; : The copper pad is recommended to connec

DS_IPM24S0B0_03202007 13 Mechanical Drawing SMD PACKAGE SIP PACKAGE RECOMMEND PWB PAD LAYOUT RECOMMEND PWB HOLE LAYOUT 1 2 3 4 5 1 2 3 4 5 7 6 1 2 3 4 5 : The copper pad is recommended to connec ote: All dimension are in millimeters (inches) standard dimension tolerance is ± 0.10(0.004”) Note t to t...

Page 14 - PART NUMBERING SYSTEM; MODEL LIST

DS_IPM24S0B0_03202007 14 PART NUMBERING SYSTEM IPM 24 S 0B0 S 03 F A Product Family Input Voltage Number of Outputs Output Voltage Package Output Current Option Code Integrated POL Module 11V ~ 36V S - Single 0B0 - programmable output 3.3V~6.5V R - SIP S - SMD 03 - 3A F- RoHS 6/6 (Lead Free) A - Sta...