Delta DVPDNET-SL - Manuals - manualsarea.com

Page 3 - DeviceNet Network Scanner DVPDNET-SL; DVP-PLC Application Manual; Warning; damages on the device or injuries to staff.; Table of Contents

DeviceNet Network Scanner DVPDNET-SL DVP-PLC Application Manual 1 Warning Please read this instruction carefully before use and follow this instruction to operate the device in order to prevent damages on the device or injuries to staff. Switch off the power before wiring. DVPDNET-SL is an OPEN TYPE...

Page 4 - DVP-PLC Application Manual

DeviceNet Network Scanner DVPDNET-SL DVP-PLC Application Manual 2 3.2 Installing DVPDNET-SL and DVP-SV MPU on DIN Rail .......................................................... 7 3.3 Connecting to DeviceNet Connection Port ...............................................................................

Page 5 - Introduction; Basic Functions of DVPDNET-SL

DeviceNet Network Scanner DVPDNET-SL DVP-PLC Application Manual 3 1 Introduction 1. To ensure correct installation and operation of DVPDNET-SL, please read this chapter carefully before using your DVPDNET-SL. 2. This chapter only provides introductory information on DVPDNET-SL. For more detailed inf...

Page 7 - Product Profile & Outline; Profiles

DeviceNet Network Scanner DVPDNET-SL DVP-PLC Application Manual 5 Electrical specification Voltage 11 ~ 25 VDC supplied by the power cable in the network Current 28mA (typical), 125mA impulse current (24 VDC) Environment Noise immunity ESD (IEC 61131-2, IEC 61000-4-2): 8KV Air Discharge EFT (IEC 611...

Page 8 - Connection

DeviceNet Network Scanner DVPDNET-SL DVP-PLC Application Manual 6 3. Power, MS, NS LED 8. Function switch 4. DIN rail clip 9. DeviceNet connection port 5. Digital indicator 2.3 DeviceNet Connection Port The connector is used on the connection to DeviceNet. Wire by using the connector enclosed with D...

Page 9 - Indicator; Port; Basic; Installing DVPDNET-SL and DVP-SV MPU on DIN Rail

DeviceNet Network Scanner DVPDNET-SL DVP-PLC Application Manual 7 OFF When the slave is off-line, the I/O data in the buffer area will be cleared. IN1 Reserved Note: z Please set up the function switch when the power is switched off. After the setup is completed, re-power DVPDNET-SL. z When DVPDNET-...

Page 10 - Connecting to DeviceNet Connection Port; Make sure you connect the cable to the right PIN.; Configuration; Corresponding Relation between DVPDNET-SL and DVP-SV

DeviceNet Network Scanner DVPDNET-SL DVP-PLC Application Manual 8 Open the DIN rail clip on DVP-SV and DVPDNET-SL. Insert DVP-SV and DVPDNET-SL onto the DIN rail. Clip up the DIN rail clips on DVP-SV and DVPDNET-SL to fix DVP-SV and DVPDNET-SL on the DIN rail, as shown below. DVPDNET 35 mm DI N ...

Page 11 - Mapping; Constructing DeviceNet Network; How to Construct a DeviceNet Network

DeviceNet Network Scanner DVPDNET-SL DVP-PLC Application Manual 9 Mapped D registers DVPDNET-SL index Output mapping Input mapping 1 D6250 ~ D6497 D6000 ~ D6247 2 D6750 ~ D6997 D6500 ~ D6747 3 D7250 ~ D7497 D7000 ~ D7247 4 D7750 ~ D7997 D7500 ~ D7747 5 D8250 ~ D8497 D8000 ~ D8247 6 D8750 ~ D8997 D85...

Page 20 - Network

DeviceNet Network Scanner DVPDNET-SL DVP-PLC Application Manual 18 Slave → DVPDNET-SL Register in DVPDNET-SL Devices in slave D6037H DI/DO module X0 ~ X7 on DVP-16SP D6037L N/A D6038H Status of LED on VFD-B D6038L Status of VFD-B D6039H High byte of frequency in VFD-B D6039L AC motor drive Low byte ...

Page 22 - Sending Explicit Message from Ladder Diagram; The Principle of Explicit Message Sending; Structure of Explicit Message

DeviceNet Network Scanner DVPDNET-SL DVP-PLC Application Manual 20 6 Sending Explicit Message from Ladder Diagram DVPDNET-SL supports the sending of explicit messages through WPL programs. 6.1 The Principle of Explicit Message Sending D V P D N E T D V P 2 8 SV R U N S T O P Dev ic eNet RJ1 2 1 4 VF...

Page 28 - Command; of; Display of Node Status on Network; Display of Node Status in Scan List

DeviceNet Network Scanner DVPDNET-SL DVP-PLC Application Manual 26 editing area to 0. When M1 = On, DVPDNET-SL will send out request message. Write 0004Hex into Class 99 >> Instance 1 >> Attribue 2 of the target equipment (node address: 02). If the communication of explicit message is ...

Page 29 - Status of DVPDNET-SL; LED

DeviceNet Network Scanner DVPDNET-SL DVP-PLC Application Manual 27 Corresponding nodes on the network PLC device b15 b14 b13 … b1 b0 D6032 Node 15 Node 14 Node 13 … Node 1 Node 0 D6033 Node 31 Node 30 Node 29 … Node 17 Node 16 D6034 Node 47 Node 46 Node 45 … Node 33 Node 32 D6035 Node 63 Node 62 Nod...

Page 32 - MEMO

DeviceNet Network Scanner DVPDNET-SL DVP-PLC Application Manual 30 MEMO