Delta 50-760 - Manuals - manualsarea.com

Page 3 - SAFETY GUIDELINES - DEFINITIONS; CALIFORNIA PROPOSITION 65

3 Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, may result in mi...

Page 4 - GENERAL SAFETY RULES

4 GENERAL SAFETY RULES READ AND UNDERSTAND ALL WARNINGS AND OPERATING INSTRUCTIONS BEFORE USING THIS EQUIPMENT. Failure to follow all instructions listed below, may result in electric shock,fire, and/or serious personal injury or property damage. IMPORTANT SAFETY INSTRUCTIONS 1. FOR YOUR OWN SAFETY,...

Page 5 - POWER CONNECTIONS

5 A separate electrical circuit should be used for your machines. This circuit should not be less than #12 wire and shouldbe protected with a 20 Amp time lag fuse. If an extension cord is used, use only 3-wire extension cords which have 3-prong grounding type plugs and matching receptacle which will...

Page 6 - EXTENSION CORDS; MINIMUM GAUGE EXTENSION CORD

6 EXTENSION CORDS Use proper extension cords. Make sure your extension cord is in good condition and is a 3-wireextension cord which has a 3-prong grounding typeplug and matching receptacle which will accept themachine’s plug. When using an extension cord, be sureto use one heavy enough to carry the...

Page 7 - FOREWORD; FUNCTIONAL DESCRIPTION

7 FOREWORD The Delta Industrial Model 50-760 Dust Collector will connect to woodworking machines that accept a 4" diameter hose.The 50-760 comes with one 1 micron filter bag and two 6 mil plastic collection bag, and a 4" x 5 ft. collection hose. FUNCTIONAL DESCRIPTION NOTICE: THE PHOTO ON TH...

Page 8 - UNPACKING AND CLEANING; ASSEMBLY; ASSEMBLY TOOLS REQUIRED

8 11 12 13 14 15 16 17 18 Fig. 1B 19 11. Hose clamp (2)12. Intake cap and ring (2)13. Bracket for bag hanging rod14. Knob for attaching legs to blower/motor assembly (4) 15. 3/8” (9.5mm) Lockwasher for attaching casters to stand (4) 16. 5/16” Small flat washers for attaching legs to blower/ motor as...

Page 9 - CASTERS

FOR YOUR OWN SAFETY, DO NOT CONNECT THE MACHINE TO THE POWER SOURCE UNTIL THE MACHINE IS COMPLETELY ASSEMBLED AND YOU READ AND UNDERSTAND THE ENTIRE INSTRUCTIONMANUAL. CASTERS 1. Turn stand (A) upside down, as shown in Fig 1C.2. Place 3/8” lockwasher on caster stud (B) and screw caster into threaded...

Page 10 - ALTERNATE SETUP; ATTACHING DUST INTAKE PORTS

10 ALTERNATE SETUP The steps so far will assemble the unit with the motoron top and dust intake ports on bottom, as shown inFig 4. This unit can be assembled with the intake port (B) Fig.5 in the up position by following the steps in “LEGS TO MOTOR/BLOWER ASSEMBLY.” The exception is to place the mot...

Page 11 - ATTACHING DUST COLLECTION BAG

11 ATTACHING DUST COLLECTION BAG USING CLOTH COVERED FLEXIBLE RING: 1. Take cloth-covered bag retainer ring (A) Fig. 8 and place it inside opening of clear plastic dustcollection bag. Fold about 6 inches of the bagdown around the retainer ring. 2. Place bag in large hole (B) Fig. 8 in motor/blower a...

Page 12 - ATTACHING HOSE TO INTAKE PORT; ATTACHING TOP FILTER BAG

12 ATTACHING HOSE TO INTAKE PORT DISCONNECT MACHINE FROM POWER SOURCE BEFORE CONNECTING ORDISCONNECTING HOSE . Model 50-760 provides two 4” dust ports. Proceed asfollows for each port with your hose. NOTE: Place open end (D) of intake cap rings around and onto ends of each dust intake port before at...

Page 13 - LOCKING SWITCH IN “OFF” POSITION

13 FOR OPERATOR SAFETY, DO NOT OPERATE THE MACHINE WITH ANY DUST INTAKE HOLES UNCOVERED. THE ROTATING FAN LOCATED INSIDE THE BLOWER HOUSING IS ACCESSIBLE THROUGH THEDUST IN-TAKE PORT AND CAN BE HAZARDOUS. ALWAYS WEAR PROPER APPAREL. DO NOT WEAR JEWELRYAND KEEP FINGERS AND ALL FOREIGN OBJECTS OUT OF ...

Page 14 - MAINTENANCE; PARTS, SERVICE OR WARRANTY ASSISTANCE; ACCESSORIES; Two Year Limited New Product Warranty; KEEP MACHINE CLEAN; FAILURE TO START; SERVICE

14 MAINTENANCE PARTS, SERVICE OR WARRANTY ASSISTANCE All Delta Machines and accessories are manufactured to high quality standards and are serviced by a networkof Porter-Cable • Delta Factory Service Centers and Delta Authorized Service Stations. To obtain additional information regarding your Delta...

Page 15 - NOTES

Page 16 - DELTA SERVICE CENTERS; CANADIAN PORTER-CABLE

The following are trademarks of PORTER-CABLE • DELTA (Las siguientes son marcas registradas de PORTER-CABLE • DELTA S.A.) (Les marques suivantes sont des marques de fabriquant de la PORTER-CABLE • DELTA): Auto-Set ® , BAMMER ® , B.O.S.S. ® , Builder’s Saw ® , Contractor’s Saw ® , Contractor’s Saw II...