Delta 36-865 - Manuals - manualsarea.com

Page 3 - SAFETY GUIDELINES - DEFINITIONS; CALIFORNIA PROPOSITION 65

3 Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, may result in mi...

Page 4 - GENERAL SAFETY RULES

4 GENERAL SAFETY RULES READ AND UNDERSTAND ALL WARNINGS AND OPERATING INSTRUCTIONS BEFORE USING THIS EQUIPMENT. Failure to follow all instructions listed below, may result in electric shock,fire, and/or serious personal injury or property damage. IMPORTANT SAFETY INSTRUCTIONS 1. FOR YOUR OWN SAFETY,...

Page 6 - POWER CONNECTIONS

6 A separate electrical circuit should be used for your machines. This circuit should not be less than #12 wire and shouldbe protected with a 20 Amp time lag fuse. If an extension cord is used, use only 3-wire extension cords which have 3-prong grounding type plugs and matching receptacle which will...

Page 7 - FOREWORD; FUNCTIONAL DESCRIPTION; EXTENSION CORDS; MINIMUM GAUGE EXTENSION CORD; UNPACKING AND CLEANING; CARTON CONTENTS

7 FOREWORD Delta Model 36-865 Versa-Feeder Stock Feeder (Variable Speed) includes a 1/8 hp 120V reversing motor. This modelcomes with three rubber feed rollers, a vertical and horizontal adjustable support arm, and a base mounting bracket. FUNCTIONAL DESCRIPTION EXTENSION CORDS Use proper extension ...

Page 9 - ASSEMBLY; ASSEMBLY TOOLS REQUIRED

9 ASSEMBLY ASSEMBLY TOOLS REQUIRED ASSEMBLY TIME ESTIMATE 3/8" Wrench5/16" Wrench 7/16" Wrench1/2" Wrench 4mm Hex WrenchPhillips Screwdriver Approximately 2-4 hours The Versa-Feeder TM can be assembled as shown in Figs. 3 or Fig. 4, depending on the operation and type of wood- workin...

Page 13 - ALTERNATE ASSEMBLY ARRANGEMENT

13 ALTERNATE ASSEMBLY ARRANGEMENT To assemble the Versa-Feeder TM in the mounting arrangement shown in Fig. 4, attaching the pivot ball to the overarm clamp assembly differs slightly. To assemble: 1. Remove the overarm (A) Fig. 24 from the overarm clamp assembly (B). 2. Remove the swivel joint (C) F...

Page 15 - MOUNTING THE VERSA-FEEDER; TO A MACHINE TABLE; MOTOR CONTROL SWITCH; OPERATION; OPERATIONAL CONTROLS AND ADJUSTMENTS

15 MOUNTING THE VERSA-FEEDER TM TO A MACHINE TABLE Decide on the location you wish to mount the Versa-Feeder TM on your machine. Refer to Figs. 44, 45, and 46 for assistance when mounting the stock feeder assembly to a table saw, jointer, or shaper. To mount the stock feederassembly to a machine tab...

Page 16 - MACHINE USE; ADJUSTING FEED RATES

16 Variable speeds from 10 FPM to 46 FPM are availablewith the stock feeder. To change the feed rates, rotatethe knob (A) Fig. 39 until the desired feed rate is indicat-ed by the pointer (B) on the knob. NOTE: Each dot on the feed rate scale (C) will increase or decrease the feed rate approximately ...

Page 17 - REPLACING FEED ROLLERS; USING THE STOCK FEEDER ON A TABLE SAW

17 REPLACING FEED ROLLERS Each feed roller is removable for repair or replacement. To remove the feed rollers: 1. Loosen the three screws (A) Fig. 42 and remove the cover (B). 2. Remove the retaining ring (C) Fig. 43, and lift off the feed roller (D). 3. Replace the rollers. 4. Replace the retaining...

Page 18 - TROUBLESHOOTING; BRUSH INSPECTION AND REPLACEMENT; USING THE STOCK FEEDER ON A SHAPER; MAINTENANCE

18 TROUBLESHOOTING For assistance with your machine, visit our website at www.deltamachinery.com for a list of service centers or call the DELTA Machinery help line at 1-800-223-7278 (In Canada call 1-800-463-3582). BRUSH INSPECTION AND REPLACEMENT DISCONNECT MACHINE FROM THE POWER SOURCE . Brush li...

Page 19 - PARTS, SERVICE OR WARRANTY ASSISTANCE; ACCESSORIES; Two Year Limited New Product Warranty; SERVICE; KEEP MACHINE CLEAN; FAILURE TO START; PROTECTING CAST IRON FROM RUST

19 PARTS, SERVICE OR WARRANTY ASSISTANCE All Delta Machines and accessories are manufactured to high quality standards and are serviced by a networkof Porter-Cable • Delta Factory Service Centers and Delta Authorized Service Stations. To obtain additional information regarding your Delta quality pro...

Page 20 - DELTA SERVICE CENTERS; CANADIAN PORTER-CABLE

The following are trademarks of PORTER-CABLE • DELTA (Las siguientes son marcas registradas de PORTER-CABLE • DELTA S.A.) (Les marques suivantes sont des marques de fabriquant de la PORTER-CABLE • DELTA): Auto-Set ® , BAMMER ® , B.O.S.S. ® , Builder’s Saw ® , Contractor’s Saw ® , Contractor’s Saw II...