Delta 32-350 - Manuals - manualsarea.com

Page 2 - TABLE OF CONTENTS

2 TABLE OF CONTENTS SAFETY RULES ..............................................................................................................................................3 ADDITIONAL SAFETY RULES FOR BORING MACHINES ..........................................................................4 UNP...

Page 3 - SAFETY RULES; WARNING: FAILURE TO FOLLOW THESE RULES

3 SAFETY RULES Woodworking can be dangerous if safe and proper operating procedures are not followed. As with all machinery, there arecertain hazards involved with the operation of the product. Using the machine with respect and caution will considerablylessen the possibility of personal injury. How...

Page 5 - ASSEMBLY

5 ASSEMBLY Fig. 2 Fig. 3 Fig. 5 Fig. 4 ASSEMBLING STANDAND MOUNTING FEET 1. Assemble front panel (A) Fig. 2, and rear panel (B) to side panels (C) with eight 5/8 inch-long screws, lock-washers and hex nuts (D). NOTE: Holes (E) Fig. 2, in side panels (C) should be at the bottom of the stand duringass...

Page 7 - CONNECTING MACHINE TO AIR SUPPLY

7 Fig. 11 ASSEMBLINGSTOCK STOP TO TABLE 1. Loosen two lock knobs (A) Fig. 11, located on the underside of table (B). 2. With the flat side of stock stop rod (C) Fig. 11, facing down, slide stop rod (C) through holes at both ends oftable (B) as shown, and fasten by rotating two lock knobs(A) clockwis...

Page 8 - GROUNDING INSTRUCTIONS

8 CONNECTING BORING MACHINE TO POWER SOURCE A separate electrical circuit should be used for your boring machine. This circuit should not beless than #12 wire and should be protected with a 15 Amp time lag fuse or circuit breaker. If anextension cord is used, use only 3-wire extension cords which ha...

Page 9 - OPERATING CONTROLS AND ADJUSTMENTS

9 INSTALLING ANDREMOVING DRILL BITS 1. Make certain the machine is disconnected from the power source. 2. Remove four screws, two of which are shown at (A) Fig. 14, and remove safety shield (B). 3. Carefully thread drill bit adapters (C) Fig. 15, supplied, into spindles (D) and tighten drill bit ada...

Page 12 - FOOT PEDAL

12 Fig. 28 Fig. 25 FOOT PEDAL The foot pedal activates the movement of the work hold-down and the boring head carriage. 1. Pushing halfway down on foot pedal (A) Fig. 25, will lower the work holddown (B) Fig. 26, when set properlyagainst the work surface as shown. 2. Once the workpiece is secure on ...

Page 13 - ADJUSTING MITER GAGE; ADJUSTING SPEED/FEED RATE OF CARRIAGE ASSEMBLY

13 The forward speed/feed rate of carriage assembly (A)Fig. 32, is governed by the air pressure. To adjust thespeed/feed rate of carriage assembly (A) Fig. 32,proceed as follows: 1. Make certain the machine is disconnected from the power source. 2. Loosen locknut (B) Fig. 32, and rotate air pressure...

Page 14 - OPERATION

14 OPERATION Fig. 33 Fig. 34 Fig. 35 Fig. 37 Fig. 36 Figs. 33 and 34, illustrate a typical end boring operation.Note that work holddown (A) Fig. 33, has been adjustedto hold workpiece (B) down on the table and that the endo f workpiece (B) is firmly held against table fence (C) andmiter gage (D). Fi...

Page 15 - MAINTENANCE; LUBRICATION

15 MAINTENANCE Fig. 41 Fig. 38 Fig. 39 Fig. 40 LUBRICATION The boring head assembly (A) Fig. 38, should be lubri-cated periodically with spindle grease Delta Part No.999-02-023-1441 through the grease fitting (B). REPLACING BORING HEAD If it is ever necessary to remove the boring head forrepair or r...

Page 16 - PARTS, SERVICE OR WARRANTY ASSISTANCE; Two Year Limited Warranty; Delta Machinery

16 PARTS, SERVICE OR WARRANTY ASSISTANCE Printed in U.S.A. Two Year Limited Warranty Delta Machinery Delta will repair or replace, at its expense and at its option, any Delta machine, machine part, ormachine accessory which in normal use has proven to be defective in workmanship or material,provided...