Delta 22-470 - Manuals

7 UNPACKING AND CLEANING Carefully unpack the machine and all loose items from the shipping container(s). Remove the protective coating fromall unpainted surfaces. This coating may be removed with a soft cloth moistened with kerosene (do not use acetone, gaso-line or lacquer thinner for this purpose...

8 ASSEMBLY ASSEMBLY TOOLS REQUIRED ASSEMBLY TIME ESTIMATE - 1-2 hours * M6 Allen wrench (supplied) * Flathead Screwdriver (Not Supplied * Forklift and Lifting Straps For Set-Up (Not Supplied) UNPACKING AND CLEANING Remove the bolts that fasten the machine to the ship-ping skid. Two lifting lugs are ...

10 Fig. 12 Fig. 11 Fig. 10 B A D E C G F K H M ELECTRICAL CONNECTIONS The planer comes wired for 220 volt operation, but it canbe wired for 440 volts. Before connecting your machineto an electrical power system, make certain the motorrating agrees with the electrical system it is to be con-nected to...

11 Fig. 13 Fig. 15 RAISING AND LOWERING THETABLE Adjust the table height by loosening lock knob (A) Fig.15, and rotating table adjusting handwheel (B). Toraise the table, turn handwheel (B) clockwise; to lowerthe table, turn handwheel (B) counterclockwise.Tighten lock knob (A) Fig. 15, after table h...

12 FEED ROLLER SPEEDS Your planer is equipped with feed roller speeds of 20and 30 feet per minute depending on belt placement onthe pulleys. As a rule, a faster feed rate is used for gen-eral planing operations, while a slower feed rate(because it provides more cuts per inch of stock) gives afiner a...

13 Fig. 20 Fig. 19 Fig. 21 TABLE ROLLERS Your planer is supplied with two table rollers (A) Fig. 21,which aid in feeding the stock by reducing friction be-tween the stock and the table and rotate as the stockis fed through the planer. 1. To raise the table rollers, loosen locking lever (B) Fig.21, a...

15 ANTI-KICKBACK FINGERS A series of anti-kickback fingers (A) Fig. 27, are providedon the infeed end of the planer to prevent kickback of theworkpiece during planing operations. These anti-kickbackfingers operate by gravity and no adjustment is required. Itis necessary, however, to inspect them occ...

19 ADJUSTING PRESSURE BAR The pressure bar is located directly behind the cutterheadand rides on the planed surface of the stock, pressing thestock downward on the table. The pressure bar must beparallel to the knives and tangent to the table and set.010” below the cutting circle. To check and adjus...

21 Fig. 48 Fig. 50 LEVELING THE TABLE The table is set parallel to the cutterhead at the factory andno further adjustment should be necessary. To check if thetable is level with the cutterhead, proceed as follows: 1. DISCONNECT THE MACHINE FROM THE POWER SOURCE . 2. Check to see if the cutterhead kn...

ADJUSTING TABLE GIBS In the unlikely event of the table developing unwantedmovement during planing operations, the table can bechecked and adjusted as follows: 1. DISCONNECT MACHINE FROM POWER SOURCE. 2. With the table in the locked position, and with a feel-er gage, measure the gap between table gi...

23 When using your machine, follow these few simple steps for achieving the best results. 1. True Up One Face – Feed one face of the board over a jointer, making thin cuts with each pass, until the entire surface is flat. 2. Plane to Thickness – Place the side you planed in STEP 1 face down and feed...

24 PARTS, SERVICE OR WARRANTY ASSISTANCE All Delta Machines and accessories are manufactured to high quality standards and are serviced by a networkof Porter-Cable • Delta Factory Service Centers and Delta Authorized Service Stations. To obtain additional information regarding your Delta quality pro...

25 Two Year Limited New Product Warranty Delta will repair or replace, at its expense and at its option, any new Delta machine, machine part, or machine accessorywhich in normal use has proven to be defective in workmanship or material, provided that the customer returns the prod-uct prepaid to a De...

The following are trademarks of PORTER-CABLE • DELTA (Las siguientes son marcas registradas de PORTER-CABLE • DELTA S.A.) (Les marques suivantes sont des marques de fabriquant de la PORTER-CABLE • DELTA): Auto-Set ® , BAMMER ® , B.O.S.S. ® , Builder’s Saw ® , Contractor’s Saw ® , Contractor’s Saw II...