Dell Force10 S60-44T- Manuals

The S60 System | 7 Orderable S60 Systems You can order the S60 in several different configurations. You can order optional modules separately. To successfully install the S60 system, ensure that you have the following: • S60 chassis (or multiple chassis, if stacking) • At least one grounded AC or DC...

The S60 System | 8 Features The S60 offers the following: • S60 CPU and switch processor • Up to 12 stacked systems • Stackable switch features • 19-inch rack-mountable • Standard 1U chassis height • Hot-swappable optional modules, PSUs, and fan modules • Integrated PSU/fan module (three fans per mo...

The S60 System | 10 In addition to the system LEDs, each port has status indicator LEDs. Table 2-2 lists the port LED displays. Table 2-2. Port LED Displays Feature Description 10/100/1000 Port LEDs • Link LED (on the left side of each port): Green—1000M Yellow—10/100M Off—No link • Activity LED (on...

Install the S60 System | 11 3 Install the S60 System To install the S60 system, Dell Force10 recommends completing the installation procedures in the order presented in this chapter. Always handle the S60 system and its components with care. Avoid dropping the system or its Field Replaceable Units (...

Install the S60 System | 12 To attach the brackets to the chassis, follow these steps: Install the Chassis into the Rack or Cabinet To permit access and airflow, ensure that there is adequate clearance surrounding the rack or within the cabinet. When you install two S60 systems near each other, to p...

Install the S60 System | 13 Attach the Ground Cable The S60 system is shipped with two 10-32 screws to attach a ground cable to the system. The cable is not included. To properly ground the system, Dell Networking recommends using a 6AWG two-hole lug, #10 hole size, 63" spacing (not included). T...

Install the S60 System | 14 Insert Optional Modules The S60 system has expansion slots at the front left and rear right of the system that you can use for stacking modules or for Small Form-Factor Pluggable Plus (SFP+) devices. Table 3-1 lists the optional modules that you can install into these exp...

Install the S60 System | 15 Install the SFP and SFP+ Optics In addition to the optional SFP+ optical modules, the S60 system has four Small Form-Factor Pluggable (SFP) optical ports in the front of the system. WARNING: ESD damage can occur if the components are mishandled. Always wear an ESD-prevent...

Install the S60 System | 16 Figure 3-1. S60 Stacking Topology with 2-port, 12G Stacking Modules Figure 3-2. S60 Stacking Topology with 1-port, 24G Stacking Modules While the diagram shows A-to-B connections, the ports are bi-directional so you can connect A-to-A or B-to-B, as shown in the examples o...

Install the S60 System | 17 Connect Two S60 Systems 2-port, 12G Stacking Modules As an option, when using the 2-port, 12G stacking modules, insert a second cable into the other open stack ports ( Figure 3-4 ). The second cable provides both backup connectivity and increased data transfer between the...

Install the S60 System | 18 Connect Three or More S60 Systems 2-port, 12G Stacking Modules As an option, when using the 2-port, 12G stacking modules, insert a second cable into the other open stack ports ( Figure 3-5 ). The second cable provides both backup connectivity and increased data transfer b...

Install the S60 System | 19 Figure 3-6. Three S60 Systems with 1-port, 24G Stacking Modules Connected in a Ring Topology Supply Power and Power Up the System Supply power to the S60 system after you have mounted them in a rack (or on a table) and have installed the optional modules. Dell Networking ...

Install the S60 System | 20 The PWR Light Emitting Diode (LED) blinks until the boot-up sequence is complete. When the boot up is complete, the PWD LED is steadily lit. The Stack ID LED displays a digit to show the position of the unit in a stacking chain. For a single chassis, a 0 displays. AC Powe...

Install the S60 System | 21 Hot-swap Units in a Stack You can add, remove, or swap units in an existing stack. The units in the stack and the new units can be already powered up or they can be powered down. All units in a stack must run the same version of the operating system. If you attempt to att...

Power Supplies | 22 4 Power Supplies The S60 system is designed to support two hot-swappable power supply units (PSUs) with integrated fans that provide the cooling for the system. There are two types of power supplies (AC or DC) and there are two airflow directions (normal and reverse). Two PSUs ar...

Power Supplies | 23 Figure 4-2. DC Power Supply Power supply 0 (PSU0) is on the left side of the system; power supply 1 (PSU1) is on the right side of the system. Install an AC or DC Power Supply The PSUs in the S60 system are field replaceable. When both PSUs are up and running, you can remove one ...

Power Supplies | 24 Replace an AC or DC Power Supply NOTE: If a PSU fails, you must completely replace it. There are no field servicable components in the PSU. To request a hardware replacement, refer to Chapter 8, Technical Support . To replace a PSU, follow these steps: 6 For DC PSUs, replace the ...

Fans and Filters | 25 5 Fans and Filters The S60 system comes from the factory with one Power Supply Unit (PSU) and one fan module installed in the system ( Figure 5-1 ). If a second (redundant) PSU is installed and running, both the fan module and the integrated fan/PSU are hot-swappable. With redu...

Fans and Filters | 26 Components • S60 Fan module • S60 Fan module - Reverse flow • S60 Fan filter • The fan filters are used on the reverse flow (R) fan modules only. Figure 5-1. The S60 Fan Module Module slot 0 is on the left side of the system; module slot 1 is on the right side of the system. In...

Fans and Filters | 27 Error messages appear when the fan tray is removed and when the temperature approaches the threshold. • When a fan tray is removed, the system displays the following message: 00:00:37: %STKUNIT0-M:CP %CHMGR-2-FAN_TRAY_BAD: Major alarm: fan tray 0 in unit 0 is missing or down • ...

Access the Console Ports | 28 6 Access the Console Ports You can access the S60 system directly through the console port at rear of the system ( Figure 6-1 ). Access the RJ-45 Console Port (RS-232) NOTE: Before starting this procedure, be sure you have a terminal emulation program already installed ...

Access the Console Ports | 29 Access the RJ-45 Console Port with a DB-9 Adapter If the DTE has a DB-9 interface, you can connect to the console port using an RJ-45 to DB-9 adapter along with the RJ-45 rollover cable. Table 6-1 lists the pin assignments. Access the USB-B Console Port The S60 system h...

S60 Specifications | 31 7 S60 Specifications This chapter the following sections: • Chassis Physical Design • Agency Compliance Chassis Physical Design Environmental Parameters AC Power Requirements Parameter Specifications Height 1.7 inches (4.3 cm) Width 17.32 inches (44.0 cm) Depth 16.73 inches (...

S60 Specifications | 32 DC Power Requirements IEEE Standards The S60 complies with the following IEEE standards: • 802.3ae 10 Gigabit Ethernet • 802.3ab 1000Base-T • 802.1p L2 Prioritization • 802.1Q VLAN Tagging, Double VLAN Tagging (Q in Q), GVRP • 802.1s Multiple Spanning Tree Protocol • 802.1w R...

S60 Specifications | 33 WARNING: Electrostatic discharge (ESD) damage can occur if the components are mishandled. Always wear an ESD-preventive wrist or heel ground strap when handling the S60 system and its components. CAUTION: The intra-building port(s) of the equipment or sub-assembly is suitable...

S60 Specifications | 34 European Union EMC Directive Conformance Statement This product is in conformity with the protection requirements of EU Council Directive 2004/108/EC on the approximation of the laws of the Member States relating to electromagnetic compatibility. Dell Networking cannot accept...

S60 Specifications | 35 Korea Compliance Korea Information China Compliance Safety Standards and Compliance Agency Certifications • CUS UL 60950-1, 1st Edition • CSA 60950-1-03, 2nd Edition • EN 60950-1, 2nd Edition • EN 60825-1, 1st Edition • EN 60825-1 Safety of Laser Products—Part 1: Equipment Cl...

S60 Specifications | 36 • EN 60825-2 Safety of Laser Products—Part 2: Safety of Optical Fibre Communication Systems • FDA Regulation 21CFR 1040.10 and 1040.11 • IEC 60950-1, 2nd Ed, including all National Deviations and Group Differences Electromagnetic Compatibility (EMC) Emissions • International:...

S60 Specifications | 37 Figure 7-1. The European WEEE symbo l In accordance with the European WEEE Directive, electrical and electronic equipment (EEE) is to be collected separately and to be reused, recycled, or recovered at end of life. Users of EEE with the WEEE marking per Annex IV of the WEEE D...

S60 Specifications | 38 Battery Replacement and Recycling CAUTION: The lithium battery is not field replaceable. Only authorized personnel should remove and replace the lithium battery. If the battery requires replacement, contact Dell Networking Technical Support. WARNING: ESD damage can occur if t...

S60 Specifications | 40 For California: Perchlorate Material — Special handling may apply. See: http://www.dtsc.ca.gov/hazardouswaste/perchlorate The foregoing notice is provided in accordance with California Code of Regulations Title 22, Division 4.5 Chapter 33. Best Management Practices for Perchl...

Technical Support | 41 8 Technical Support This appendix contains the following sections: • The iSupport Website • Contacting the Technical Assistance Center • Requesting a Hardware Replacement The iSupport Website iSupport provides a range of documents and tools to assist you with effectively using...

Technical Support | 42 Contacting the Technical Assistance Center How to Contact Dell Networking TAC Log in to iSupport at http://support.dell.com/force10 and select the Service Request tab. Information to Submit When Opening a Support Case • Your name, company name, phone number, and E-mail address...

Technical Support | 43 Requesting a Hardware Replacement To request replacement hardware, follow these steps: Step Task 1 Determine the part number and serial number of the component. To list the numbers for all components installed in the chassis, use the show hardware command. 2 Request a Return M...