Dell FD332 - Manuals

Indicator pattern Description Solid blue The storage sled is powered on, and is operating normally. Blinking blue The compute sled to which the storage sled is mapped, is identified. Blinking amber The storage sled or any component inside the storage sled is in fault condition. Hard drive/SSD indica...

Figure 4. Storage controller card indicators 1. indicator for PERC 1 2. indicator for PERC 2 NOTE: The PERC 2 indicator is always Off if you are using a single PERC. Indicator pattern Description Off Storage controller card is offline Solid blue Storage controller card is online Blinks blue Storage ...

To... Refer to... Know about how to configure storage mode in the storage sled and remote management of the storage sled from the Chassis Management Controller (CMC) interface PowerEdge FX2/FX2s CMC User’s Guide at dell.com/esmmanuals Know about remote management of the storage sled from the integra...

2 Performing initial system configuration After you receive your PowerEdge FD332 system, you must set up your system in the enclosure. If your storage sled has shipped pre-installed in the enclosure, it is recommended that you remove the sled before you install the enclosure in the rack, to reduce c...

• the iDRAC of the compute sled to which the storage sled is mapped. For more information, see the iDRAC User’s Guide at dell.com/esmmanuals . • the Dell OpenManage Server Administration (OMSA) software. For more information, see dell.com/ openmanagemanuals . Downloading drivers and firmware It is r...

3 Storage sled mapping configurations The storage controller(s) inside a storage sled map to compute sled(s) in the enclosure. PowerEdge FX2s supports multiple storage sled to compute sled mapping configurations. NOTE: Storage sled to compute sled mapping is pre-configured. NOTE: The PowerEdge FM120...

Figure 6. Single PERC/joined mode mapping configuration—four-bay chassis (one compute sled) Figure 7. Single PERC/joined mode mapping configuration—six-bay chassis Figure 8. Single PERC/joined mode mapping configuration—three-bay chassis Split mode mapping configurations CAUTION: Changing the storag...

• Split Dual Host mode Split single host mapping configuration In the split single host mapping configuration, dual controllers inside a storage sled map to a single compute sled.The following enclosure configurations support split single host mapping. • Four-bay chassis with two compute sleds—dual ...

NOTE: PowerEdge FX2s supports multiple split dual host mapping configurations. You must select the desired configuration based on your intended usage. The following are examples of split dual host mapping configurations. Figure 12. Split dual host configuration—four-bay chassis Figure 13. Split dual...

4 Installing and removing storage sled components This section provides information on installing and removing the storage sled components. For information on removing and installing the compute sled components, see the relevant sled Owner’s Manual at dell.com/poweredgemanuals . For information on i...

The storage sled also turns off. 2. Remove the storage sled from the enclosure. 3. Install the I/O connector cover. Related Links Removing a storage sled After working inside your system 1. Remove the I/O connector cover. 2. Install the storage sled in the enclosure. 3. Turn on the compute sled(s) t...

Figure 17. Removing and installing the I/O connector cover 1. storage sled 2. I/O connector cover Next steps Install the storage sled or sled blank. Related Links Safety instructionsStorage sled mapping configurations Installing a storage sled Prerequisites CAUTION: Many repairs may only be done by ...

Inside the sled Figure 19. Inside the sled 1. storage controller module 2. I/O connector to enclosure midplane 3. storage controller module cable 4. drive drawer 5. hard-drive/SSD release tab (16) 6. dotted line on top of storage sled Drive drawer The drive drawer supports up to 16 hot swap hard dri...

Opening the drive drawer Prerequisites CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to s...

Figure 21. Service caution label on the drive drawer Next steps Close the drive drawer. Related Links Closing the drive drawer Closing the drive drawer Prerequisites CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs a...

Figure 22. Closing the drive drawer 1. sled lock (2) 2. drive drawer 3. dotted line on the drive drawer Related Links Opening the drive drawer Mini Enterprise Service Tag The Mini Enterprise Service Tag is a removable label panel located on the storage sled front panel, which lists the system Servic...

1. Ensure that you read the Safety instructions . 2. Keep the #1 Phillips screwdriver ready. Steps1. Pull the drive drawer handle on the front panel of the storage sled, and keep it in open position. 2. Remove the screw securing the Mini Enterprise Service Tag (MEST) to the sled front panel. 3. Remo...

Steps1. Align the edge of the MEST opposite to the screw hole end, with the slot on the sled front panel. 2. Align the screw hole on the tag with the screw hole on the sled front panel and install the screw to secure the tag to the sled front panel. 3. Close the drive drawer handle. Related Links Re...

Figure 25. Release tabs for the top and bottom hard drives/SSDs Next steps Install the hard drive/SSD assembly. Related Links Installing a hard drive/SSD assemblyOpening the drive drawer Installing a hard drive/SSD assembly Prerequisites CAUTION: Many repairs may only be done by a certified service ...

Removing a hard drive/SSD from the drive rails Prerequisites CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support...

3. drive rail with release handle 4. screw (4) Next steps Install the hard drive/SSD into the drive rails. Related Links Installing a hard drive/SSD into the drive railsOpening the drive drawerClosing the drive drawerRemoving a hard drive/SSD assembly Installing a hard drive/SSD into the drive rails...

• FD33xS—storage controller module with single PERC• FD33xD—storage controller module with dual PERC NOTE: The default mode for the storage controller module is HBA mode. To enable RAID mode for the SCM, you must upgrade to RAID mode licensing. For more information on RAID mode licensing, see the Po...

Figure 28. Removing and installing the storage controller module 1. storage controller module 2. screw (3) 3. SCM cable touch point 4. SCM cable screw (2) 5. touch point on the SCM (4) 6. connector on midplane interface module Next steps Install the storage controller module. Related Links Installin...

NOTE: This is a field replaceable unit (FRU). Removal and installation procedures must be performed only by Dell certified service technicians. 1. Ensure that you read the Safety instructions . 2. Follow the procedure listed in Before working inside your system . 3. Keep the T15 Torx screwdriver rea...

Figure 30. Removing and installing the bezel assembly 1. screw (7) 2. top side of the sled 3. bezel assembly Next steps Install the bezel assembly. Related Links Installing the bezel assemblyRemoving the Mini Enterprise Service Tag Installing the bezel assembly Prerequisites CAUTION: Many repairs ma...

5 Troubleshooting your system Safety first—for you and your system CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and s...

Related Links Hard drive/SSD indicatorsRemoving a hard drive/SSD assemblyInstalling a hard drive/SSD assembly Troubleshooting a storage controller module Prerequisites CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs...

NOTE: Warning messages are generated by either the application or the operating system. For more information, see the documentation that accompanied the operating system or application. Diagnostic messages The system diagnostic utilities may issue messages if you run diagnostic tests on your system....

6 Using system diagnostics NOTE: You cannot run diagnostics tests on PowerEdge FD332. You must run system diagnostics from the compute sled(s) to which PowerEdge FD332 is mapped. If you experience a problem with your system, run the system diagnostics before contacting Dell for technical assistance....

Running the Embedded System Diagnostics from the Dell Lifecycle Controller 1. As the system boots, press <F11>. 2. Select Hardware Diagnostics → Run Hardware Diagnostics . The ePSA Pre-boot System Assessment window is displayed, listing all devices detected in the system. The diagnostics start...

7 Technical specifications—PowerEdge FD332 Physical Width 21.09 cm (8.3 inch) Height 4.01 cm (1.57 inch) Depth 52.36 cm (20.61 inch) Weight (maximum) 7.93 kg (17.48 lb) Drives Hard drives/SSDs Up to sixteen 2.5-inch, hot swap SAS or SATA hard drives/SSDs RAID Controller Controller type PERC FD33xS, ...

8 Getting help Contacting Dell Dell provides several online and telephone-based support and service options. If you do not have an active Internet connection, you can find contact information on your purchase invoice, packing slip, bill, or Dell product catalog. Availability varies by country and pr...