Page 3 - Contents
Contents 1 About your Dell PowerEdge FD332................................................................... 5 Terms used in this document ............................................................................................................... 5 Front panel features and indicators—PowerEdge ...
Page 5 - About your Dell PowerEdge FD332; Terms used in this document
1 About your Dell PowerEdge FD332 The Dell PowerEdge FD332 is a storage sled supported on the Dell PowerEdge FX2s enclosure. PowerEdge FD332 supports up to sixteen hot swap 2.5 inch hard drives/SSDs, and a storage controller module with single or dual controller modes. Terms used in this document Th...
Page 6 - Front panel features and indicators—PowerEdge FD332; Storage sled status indicator
Front panel features and indicators—PowerEdge FD332 Figure 1. Front panel features and indicators Item Indicator, Button, or Connector Description 1 Drive drawer Consists of up to sixteen 2.5 inch hard drives/SSDs. 2 Mini Enterprise Service Tag (MEST) A removable label panel that lists the system Se...
Page 7 - Hard drive/SSD indicators; Storage controller card indicators
Indicator pattern Description Solid blue The storage sled is powered on, and is operating normally. Blinking blue The compute sled to which the storage sled is mapped, is identified. Blinking amber The storage sled or any component inside the storage sled is in fault condition. Hard drive/SSD indica...
Page 8 - Documentation matrix
Figure 4. Storage controller card indicators 1. indicator for PERC 1 2. indicator for PERC 2 NOTE: The PERC 2 indicator is always Off if you are using a single PERC. Indicator pattern Description Off Storage controller card is offline Solid blue Storage controller card is online Blinks blue Storage ...
Page 9 - Quick Resource Locator
To... Refer to... Know about how to configure storage mode in the storage sled and remote management of the storage sled from the Chassis Management Controller (CMC) interface PowerEdge FX2/FX2s CMC User’s Guide at dell.com/esmmanuals Know about remote management of the storage sled from the integra...
Page 10 - Performing initial system configuration; Setting up your PowerEdge FD332; Managing your system remotely
2 Performing initial system configuration After you receive your PowerEdge FD332 system, you must set up your system in the enclosure. If your storage sled has shipped pre-installed in the enclosure, it is recommended that you remove the sled before you install the enclosure in the rack, to reduce c...
Page 11 - Downloading drivers and firmware
• the iDRAC of the compute sled to which the storage sled is mapped. For more information, see the iDRAC User’s Guide at dell.com/esmmanuals . • the Dell OpenManage Server Administration (OMSA) software. For more information, see dell.com/ openmanagemanuals . Downloading drivers and firmware It is r...
Page 12 - Storage sled mapping configurations; Single PERC and joined mode mapping configurations
3 Storage sled mapping configurations The storage controller(s) inside a storage sled map to compute sled(s) in the enclosure. PowerEdge FX2s supports multiple storage sled to compute sled mapping configurations. NOTE: Storage sled to compute sled mapping is pre-configured. NOTE: The PowerEdge FM120...
Page 13 - Split mode mapping configurations
Figure 6. Single PERC/joined mode mapping configuration—four-bay chassis (one compute sled) Figure 7. Single PERC/joined mode mapping configuration—six-bay chassis Figure 8. Single PERC/joined mode mapping configuration—three-bay chassis Split mode mapping configurations CAUTION: Changing the storag...
Page 14 - Split single host mapping configuration
• Split Dual Host mode Split single host mapping configuration In the split single host mapping configuration, dual controllers inside a storage sled map to a single compute sled.The following enclosure configurations support split single host mapping. • Four-bay chassis with two compute sleds—dual ...
Page 15 - Drive to storage controller mapping
NOTE: PowerEdge FX2s supports multiple split dual host mapping configurations. You must select the desired configuration based on your intended usage. The following are examples of split dual host mapping configurations. Figure 12. Split dual host configuration—four-bay chassis Figure 13. Split dual...
Page 17 - Customer and field replaceable units—PowerEdge FD332; Safety instructions
4 Installing and removing storage sled components This section provides information on installing and removing the storage sled components. For information on removing and installing the compute sled components, see the relevant sled Owner’s Manual at dell.com/poweredgemanuals . For information on i...
Page 18 - After working inside your system; Recommended tools
The storage sled also turns off. 2. Remove the storage sled from the enclosure. 3. Install the I/O connector cover. Related Links Removing a storage sled After working inside your system 1. Remove the I/O connector cover. 2. Install the storage sled in the enclosure. 3. Turn on the compute sled(s) t...
Page 20 - Installing a storage sled
Figure 17. Removing and installing the I/O connector cover 1. storage sled 2. I/O connector cover Next steps Install the storage sled or sled blank. Related Links Safety instructionsStorage sled mapping configurations Installing a storage sled Prerequisites CAUTION: Many repairs may only be done by ...
Page 23 - Inside the sled; Drive drawer
Inside the sled Figure 19. Inside the sled 1. storage controller module 2. I/O connector to enclosure midplane 3. storage controller module cable 4. drive drawer 5. hard-drive/SSD release tab (16) 6. dotted line on top of storage sled Drive drawer The drive drawer supports up to 16 hot swap hard dri...
Page 24 - Opening the drive drawer
Opening the drive drawer Prerequisites CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to s...
Page 25 - Closing the drive drawer
Figure 21. Service caution label on the drive drawer Next steps Close the drive drawer. Related Links Closing the drive drawer Closing the drive drawer Prerequisites CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs a...
Page 26 - Mini Enterprise Service Tag; Removing the Mini Enterprise Service Tag
Figure 22. Closing the drive drawer 1. sled lock (2) 2. drive drawer 3. dotted line on the drive drawer Related Links Opening the drive drawer Mini Enterprise Service Tag The Mini Enterprise Service Tag is a removable label panel located on the storage sled front panel, which lists the system Servic...
Page 27 - Installing the Mini Enterprise Service Tag
1. Ensure that you read the Safety instructions . 2. Keep the #1 Phillips screwdriver ready. Steps1. Pull the drive drawer handle on the front panel of the storage sled, and keep it in open position. 2. Remove the screw securing the Mini Enterprise Service Tag (MEST) to the sled front panel. 3. Remo...
Page 28 - Hard drive/SSD assembly; Removing a hard drive/SSD assembly
Steps1. Align the edge of the MEST opposite to the screw hole end, with the slot on the sled front panel. 2. Align the screw hole on the tag with the screw hole on the sled front panel and install the screw to secure the tag to the sled front panel. 3. Close the drive drawer handle. Related Links Re...
Page 30 - Installing a hard drive/SSD assembly
Figure 25. Release tabs for the top and bottom hard drives/SSDs Next steps Install the hard drive/SSD assembly. Related Links Installing a hard drive/SSD assemblyOpening the drive drawer Installing a hard drive/SSD assembly Prerequisites CAUTION: Many repairs may only be done by a certified service ...
Page 33 - Removing a hard drive/SSD from the drive rails
Removing a hard drive/SSD from the drive rails Prerequisites CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support...
Page 34 - Installing a hard drive/SSD into the drive rails; Storage controller module
3. drive rail with release handle 4. screw (4) Next steps Install the hard drive/SSD into the drive rails. Related Links Installing a hard drive/SSD into the drive railsOpening the drive drawerClosing the drive drawerRemoving a hard drive/SSD assembly Installing a hard drive/SSD into the drive rails...
Page 35 - Removing the storage controller module
• FD33xS—storage controller module with single PERC• FD33xD—storage controller module with dual PERC NOTE: The default mode for the storage controller module is HBA mode. To enable RAID mode for the SCM, you must upgrade to RAID mode licensing. For more information on RAID mode licensing, see the Po...
Page 36 - Installing the storage controller module
Figure 28. Removing and installing the storage controller module 1. storage controller module 2. screw (3) 3. SCM cable touch point 4. SCM cable screw (2) 5. touch point on the SCM (4) 6. connector on midplane interface module Next steps Install the storage controller module. Related Links Installin...
Page 37 - Bezel assembly; Removing the bezel assembly
NOTE: This is a field replaceable unit (FRU). Removal and installation procedures must be performed only by Dell certified service technicians. 1. Ensure that you read the Safety instructions . 2. Follow the procedure listed in Before working inside your system . 3. Keep the T15 Torx screwdriver rea...
Page 39 - Installing the bezel assembly
Figure 30. Removing and installing the bezel assembly 1. screw (7) 2. top side of the sled 3. bezel assembly Next steps Install the bezel assembly. Related Links Installing the bezel assemblyRemoving the Mini Enterprise Service Tag Installing the bezel assembly Prerequisites CAUTION: Many repairs ma...
Page 41 - Troubleshooting your system; Safety first—for you and your system; Troubleshooting hard drives/SSDs
5 Troubleshooting your system Safety first—for you and your system CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and s...
Page 42 - Troubleshooting a storage controller module; System messages; Warning messages
Related Links Hard drive/SSD indicatorsRemoving a hard drive/SSD assemblyInstalling a hard drive/SSD assembly Troubleshooting a storage controller module Prerequisites CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs...
Page 43 - Diagnostic messages; Alert messages
NOTE: Warning messages are generated by either the application or the operating system. For more information, see the documentation that accompanied the operating system or application. Diagnostic messages The system diagnostic utilities may issue messages if you run diagnostic tests on your system....
Page 44 - Dell Embedded System Diagnostics; When to use the Embedded System Diagnostics
6 Using system diagnostics NOTE: You cannot run diagnostics tests on PowerEdge FD332. You must run system diagnostics from the compute sled(s) to which PowerEdge FD332 is mapped. If you experience a problem with your system, run the system diagnostics before contacting Dell for technical assistance....
Page 45 - Running Embedded System Diagnostics from an external media; System diagnostics controls
Running the Embedded System Diagnostics from the Dell Lifecycle Controller 1. As the system boots, press <F11>. 2. Select Hardware Diagnostics → Run Hardware Diagnostics . The ePSA Pre-boot System Assessment window is displayed, listing all devices detected in the system. The diagnostics start...
Page 46 - Technical specifications—PowerEdge
7 Technical specifications—PowerEdge FD332 Physical Width 21.09 cm (8.3 inch) Height 4.01 cm (1.57 inch) Depth 52.36 cm (20.61 inch) Weight (maximum) 7.93 kg (17.48 lb) Drives Hard drives/SSDs Up to sixteen 2.5-inch, hot swap SAS or SATA hard drives/SSDs RAID Controller Controller type PERC FD33xS, ...
Page 49 - Getting help; Contacting Dell; Locating your system Service Tag
8 Getting help Contacting Dell Dell provides several online and telephone-based support and service options. If you do not have an active Internet connection, you can find contact information on your purchase invoice, packing slip, bill, or Dell product catalog. Availability varies by country and pr...
