DCS GDSBE1-302-N - Manuals

5 SAFETY AND WARNINGS ! WARNING! Hot Surface Hazard Failure to follow this advice may result in fire, burns, scalds or personal injury. • Accessible parts may become hot during use.• When in use, do not touch the burner, grate, or immediate surrounding area as these areas become extremely hot. Clean...

6 ! WARNING! Explosion Hazard Failure to follow this advice may result in injury or death • If you smell gas, do not use the appliance. • Do not use water on grease fires, a violent steam explosion may result. Turn all burners off, then smother fire or flame or use dry chemical or foam-type extingui...

7 z z Do not store a full LP tank in direct sunlight. z z After a period of storage or non-use, the appliance should be checked for gas leaks, deterioration, proper assembly, and burner obstructions before use. General Use z z This appliance is not intended to be installed in or on recreational vehi...

8 Gas requirements z z This appliance can be used with any brand of 20lb LP gas tank provided it is compatible with a proper retention device (not supplied). z z The LP gas cylinder must be: z z Designed for use with a Type 1 system only. z z Constructed and marked in accordance with the Specificati...

9 BEFORE YOU BEGIN z z Ensure the installer has completed the final checklist in the installation instructions. z z Read this guide, taking special note of the Safety and warnings section. z z Remove all packaging and dispose of it responsibly. Recycle items that you can. Seasoning the griddle 1 Cle...

10 LIGHTING INSTRUCTIONS | SIDE BURNER 1 If you are using propane gas, a slight pop or flash may occur at the burner ports a few seconds after the burner has been turned OFF . This is normal for propane gas. 2 3 Push in and hold the selected dial for 2 seconds before turning to HI . Hold for 5 secon...

12 LIGHTING INSTRUCTIONS | GRIDDLE If burner does not light after several attempts turn the dial to OFF and refer to the troubleshooting section. 2 3 The griddle burner is equipped with a thermocouple and safety valve system which monitors the burner. This will turn the gas off if the burner isn’t l...

14 LEAK TESTING 2 1 3 Remove the 2 screws securing the valve panel to the unit using a Phillips screwdriver. Remove all dials by pulling outwards. Pull the valve panel down then outward and unplug any wires. Removing the valve panel A complete gas tightness check must be performed at the installatio...

16 LOW FLAME ADJUSTMENT 1 3 4 2 Remove the dial. While holding the valve shaft with pliers, insert a flat-tipped screwdriver into the shaft and, while viewing the burner, adjust to a minimum stable flame. Push in and hold the selected dial for 2 seconds before turning to HI . Hold for 10 seconds to ...

17 CARE AND CLEANING Stainless steel Always use the mildest cleaning method first. Do not use steel wool to clean the product as it will scratch the surface. Burner grates For durability and optimal performance, the side burner grates are crafted using porcelain enamel over cast iron. It is recommen...

18 TROUBLESHOOTING PROBLEM POSSIBLE CAUSES WHAT TO DO The burner won't light when the ignition is pushed There is no gas flowing to the unit. Check gas supply and connections. Ensure no air is trapped in line. There is a something blocking the air or gas flow. Check all openings for blockages. Burne...

19 WARRANTY AND SERVICE Complete and keep for safe reference: Mode Serial No. Purchase Date Purchaser Dealer Suburb Town Country Before you call for service or assistance Refer to the installation instructions and your user guide and check that: z z Your product is correctly installed. z z You are f...

U S C A 5 9 2 075 A 1 1 .1 9 DCSAPPLIANCES.COM © Fisher & Paykel Appliances 2019. All rights reserved. The product specifications in this document apply to the specific products and models described at the date of issue. Under our policy of continuous product improvement, these specifications ma...