Dayton SPA1200/2400DSP - Manuals

Page 4 - Subwoofer Power Amplifiers; Table of Contents

(4) Operating Guide: Dayton Audio SPA1200/2400DSP Subwoofer Power Amplifiers Table of Contents Back panel and input/output (I/O) deﬁnition ........................................................... 5 SPA1200DSP and SPA2400DSP wiring .....................................................................

Page 6 - Do NOT bridge outputs. Dual voice coil and dual driver loads only!

(6) SPA1200DSP and SPA2400DSP wiring  SPA1200DSP  SPA2400DSP - NOTE: Do NOT bridge outputs. Dual voice coil and dual driver loads only!

Page 7 - Feature control-panel key; Green LED when amp is operating normally

(7) Feature control-panel key • Power ON LED: Green LED when amp is operating normally • Standby (STB ) LED : Red when amp is in energy saving “stand by” state • LIMIT LED (Yellow): Lit when Limiter is active • FEATURE SETUP: Single knob digital actuator with single/double-click enabled with rotary ...

Page 8 - Amp system block diagram

Page 11 - Starting iEQ; : Selecting the GUI’s

(11) Custom algorithms apply intelligent multi-band room equalization (iEQ™) The included 20Hz-capable iEQ microphone allows estimation of your room’s natural frequency response characteristics and precisely applies PEQ filters to compensate for inevitable response anomalies. Plug the microphone’s 3...

Page 14 - iOS Subwoofer Remote Control “App” Guide; Your SPA1200 or 2400DSP amp has its own internal Wi-Fi communica; Note: App Coming Soon; Discover the app (click page for

(14) iOS Subwoofer Remote Control “App” Guide Your SPA1200 or 2400DSP amp has its own internal Wi-Fi communica chip to allow for tuning and setup of your sub remotely via the dedicated Dayton Audio SubRemote iPhone Control “App”. Note: App Coming Soon The IOS app is currently going through the Apple...

Page 15 - If you have; not; connected your iPhone to the amp, the app will

(15) 3. Once the Wi-Fi successfully links to the sub, open the app to remotely control your sub’s amp. Note: If you have not connected your iPhone to the amp, the app will automatically enter “demo mode”. The demo mode is just a demonstration of each function. Optimally “smooth” operation is not fun...

Page 16 - Firmware Update Guide:; procedure if such an update is provided to all amp owners:

(16) Firmware Update Guide: Bug fixes or feature improvements may be introduced via Dayton Audio “firmware” updates. Use this procedure if such an update is provided to all amp owners: 1. Turn off the amp from the main power switch (next to power cord inlet). 2. Press and hold the control-panel’s fe...

Page 17 - above “Load File” button:

(17) 5. Load the updated firmware file from your saved location and select which new version by clicking the above “Load File” button: 6. When the firmware update is loaded, the below panel and green “progress bar” will show:

Page 19 - Press “RUN”; or; cycle power on your amp and the device will now run the new

(19) 9. Press “RUN” or cycle power on your amp and the device will now run the new ﬁ rmware version! 10. To validate your ﬁ rmware was successfully updated you can note a new opera tin g system version number “V.X.0X” on amp boot-up.

Page 20 - DSP Functions; Feature C; ti; Advanced C; GUI gives post-correc

DSP Functions (20) Feature C o ntr o ller (LCD mat rix, si ngle -kn o b, bezel m o unted ) a) V o lume: Range: 0 ~ -100dB, Step: 1dB b) High pa ss Filter : o Frequency Select: 31.5Hz ~ 125Hz, Step: 1 / 6 Oct. Sl o pe: Flat/-12dB/-24dB A. L o w pa ss Filter : a) Frequency Range: 31.5Hz ~125Hz, Step: ...

Page 21 - Base Specifications (AudioPrecision

Base Speciﬁcations (AudioPrecision ®) (21) Parameters Test condi ti ons Typical value I n p u t s en si ti vity RCA IN 1200W/4ohms @230VAC XLR IN 1200W/4ohms @230VAC SPDIF IN 1200W/4ohms @230VAC 280mV 280mV -10dBFS Gai n AMP output 80Hz @ 1W output +48dB I n p u t sat ur a tion level RCA le ft or ri...