Datalogic C-BOX 150 - Manuals

GUIDE TO INSTALLATION The following can be used as a checklist to verify all of the steps necessary for complete installation of the C-BOX 150. 1) Read all information in the section "Safety Precautions" at the beginning of this manual. 2) Correctly position and mount the C-BOX 150 within th...

INTRODUCTION 1 1 INTRODUCTION 1.1 PRODUCT DESCRIPTION The C-BOX 150 is a connection box which can be used as an accessory to several Datalogic family scanners. Its main feature is to make the substitution of a Datalogic scanner in an installation plain and easy. To achieve this goal the C-BOX 150 pr...

C-BOX 150 1 1.2 C-BOX 150 COMPATIBLE DEVICES The C-BOX 150 can be connected to the following scanners through the 25-pin connector illustrated in Figure A. Scanner Configuration Tool DS1100 * WinHost™ DS2100A WinHost™ DS2100N Genius™ DS2200 * WinHost™ DS2400A WinHost™ DS2400N Genius™ DS4600A WinHost...

INSTALLATION 2 2 INSTALLATION 2.1 PACKAGE CONTENTS Verify that the C-BOX 150 and all the parts supplied with the equipment are present and intact when opening the packaging; the list of parts includes: 1) C-BOX 150 2) Installation manual 3) C-BOX 150 configuration CD-ROM 4) 2 mounting screws 5) Grou...

C-BOX 150 2 2.2 OPENING THE DEVICE To install the C-BOX 150 or during normal maintenance, it is necessary to open it by unscrewing the four cover screws: CAUTION The C-BOX 150 must be disconnected from the power supply during this operation. Figure 2 - Opening the C-BOX 150 It is possible to perform...

INSTALLATION 2 2.3 MECHANICAL INSTALLATION The diagram below gives the overall dimensions of the C-BOX 150 and may be used for its installation. mm inch Ø3.5 [Ø0.14] 12 [0 .47 ] 66 [2 .60] 12 [0 .47 ] 5 [0.20] 150 [5.91] 5 [0.20] 40 [1 .57] 161 [6.34] 90 [3 .5 4] 89.8 [3.54] 114.5 [4.51] Figure 3 - ...

INSTALLATION 2 2.4 ELECTRICAL CONNECTIONS AND HARDWARE SETUP The following figure shows the typical layout. SCANNER AUXILIARY INTERFACE C-BOX 150 SCANNER SCANNER CONFIGURATION PC SYSTEM CABLES Figure 5 – System Layout A PC can be connected to the C-BOX 150 (and consequently to the scanner auxiliary ...

C-BOX 150 2 After system functioning has been verified, close the C-BOX 150 using the 4 cover screws making sure the rubber seal is fitted correctly between the parts of the housing. NOTE It is recommended to use the dedicated grounding cable (included in the package) to improve the C-BOX 150 noise ...

INSTALLATION 2 C-BOX 1 2 VS GND USER INTERFACE GND V+ (10 - 30 Vdc) Figure 7 - Power Supply Connections The power supply must be between 10 and 30 Vdc only. NOTE Pin 1 is also electrically connected to pins 3 and 5, just as pin 2 is electrically connected to pins 4 and 6. This is useful for external...

C-BOX 150 2 • Using a device such as a screwdriver, push down on the lever directly next to the clamp (see Figure 8). • Insert the wire into the clamp and release the lever. The wire will now be held in the spring clamp. Figure 8 - System Cable Connections The wiring used can be solid or stranded bu...

INSTALLATION 2 The C-BOX 150 spring clamp connector pinouts are indicated in the following table. Refer to the scanner Reference Manual for details. Scanner Pinouts Pin Name 1, 3, 5 VS 2, 4, 6 GND 7, 8 EARTH GROUND *9, 13 RS485 CABLE SHIELD 20, 40 RESERVED 35 TX AUX 37 RX AUX DS1100 DS2200 DS2100A D...

C-BOX 150 2 2.4.3 Scanner Chassis Grounding Jumper Settings The scanner chassis grounding method can be selected by positioning a jumper (see Figure 9). In this way the scanner chassis can be connected to earth ground (only if pins 7 or 8 are connected to a good earth ground) or to the power supply ...

INSTALLATION 2 2.4.5 RS485 Bus Termination ON OFF Figure 11 - Termination Resistance Switch This switch enables or disables the insertion of the bus termination resistor for RS485 Half Duplex Multidrop applications. CAUTION In Multiplexer applications the termination resistor must be enabled ONLY on...

C-BOX 150 2 2.4.7 OM4000 Jumper Settings J6 J5 Figure 13 - OM4000 Jumpers The jumpers allow connection to the EXT TRIG signals on separate spring clamp terminals for applications which use the OM4000 Oscillating Mirror in Trigger Mode. They are used together and they have the following significance:...

INSTALLATION 2 9-pin C-Box 150 connector pinout in Normal mode Pin Name Function 1 NC 2 RXA Auxiliary RS232 3 TXA Auxiliary RS232 4 NC 5 GND Ground 6 NC 7 RESERVED Device Dependent Signal 8 RESERVED Device Dependent Signal 9 NC POSITION MODE CFG : When the switch is in this position, the C-BOX 150 c...

C-BOX 150 2 2.5 OPERATING MODES With the C-BOX 150, the following operating modes are possible: Normal Operation: At power on, the C-BOX 150 tries to connect to the scanner. Once the connection procedure is completed the C-BOX 150 verifies if an Automatic SEND command must be executed. While executi...

INSTALLATION 2 2. Release the buttons. 3. Press the left button corresponding to the GET function, the center button corresponding to the TEST function or the right button corresponding to the SEND function. NOTE Once the buttons are released in step 1, a ten-second timeout starts. If no button is p...

C-BOX 150 2 2.5.2 LED Indicators Warning (red) Pow n) er on (gree Power polarity error (red) TX (green) Status (yellow) Figure 16 - LED Indicators The internal LEDs of the C-BOX 150 (see Figure above) indicate the following: POWER ON ( PWR ) (green) indicates the C-BOX 150 is connected to the power ...

C-BOX 150 2 2.6 TYPICAL LAYOUTS 2.6.1 1000, 2000A/N, 4000 Family Scanners For 1000, 2000A/N and 4000 scanner families which operate in a point-to-point single scanner configuration, a typical layout is shown below and the C-BOX 150 is connected as follows. Laptop Host Scanner 1 2 3 1 2 3 M ain seria...

INSTALLATION 2 2.6.2 2000N Family Scanners For 2000N scanner families which operate in an ID-NET™ network configuration, a typical layout is shown below and the C-BOX 150/100s are connected as follows. Figure 18 – Typical ID-NET™ scanner Layout C-BOX 150 can perform Backup/Restore of a whole cluster...

INSTALLATION 2 In order to perform Backup/Restore of Master only, the C-BOX 150 Cluster GET/SEND parameter must be configured to "Master only", see the WinHost Help On-Line . 2.7 SCANNER REPLACEMENT If you have to replace the scanner with another one: 1. Switch-off the system. 2. Connect the...

C-BOX 150 3 3 TECHNICAL FEATURES ELECTRICAL FEATURES Power Supply voltage 10 to 30 Vdc Power consumption max. 2.5 W + scanner USER INTERFACE LED indicators Power ON, Warning, Status Tx, Polarity inversion PHYSICAL FEATURES Mechanical dimensions 161 x 114.5 x 40 mm (6.34 x 4.51 x 1.57 in) Weight abou...

DECLARATION OF CONFORMITY 07 Datalogic Automation S.r.l., Via S. Vitalino 13 40012 - Lippo di Calderara Bologna - Italy dichiara che declares that the déclare que le bescheinigt, daß das Gerät declare que el C-BOX-XXX Connection Box; e tutti i suoi modelli and all its models et tous ses modèles und ...

www.automation.datalogic.com C-BOX 150 Installation Manual