Crestron Power Switching - Manuals

Page 2 - Physical Description; DIMENSION; CRESTRON GREEN LIGHT Power Switching

Power Switching CRESTRON GREEN LIGHT™ Physical Description This section shows the exterior and interior dimensions of the CRESTRON GREEN LIGHT cabinet. External Dimensions of CRESTRON GREEN LIGHT Power Switching Cabinets KNOCKOUT (FOR 3 4 " (19 MM) CONDUIT) TYPICAL BOTH SIDES TECHNICAL KNOCKOUTS...

Page 3 - Service 277 Service

CRESTRON GREEN LIGHT™ Power Switching Interior Dimensions of CRESTRON GREEN LIGHT Cabinets (120/208 VAC, left; 277/480 VAC, right) H1 H1 1 7 8 " (48 mm) 8 1 8 " (207 mm) 1 7 8 " (48 mm) 6 1 4 " (159 mm) 2" (51 mm) 2" (51 mm) 8" (204 mm) 3 7 8 " (99 mm) Interior Dimens...

Page 4 - Installation; Observe the following when installing the cabinet:

Power Switching CRESTRON GREEN LIGHT™ Installation Observe the following when installing the cabinet: • The cabinet must be mounted by a licensed electrician in accordance with all national and local codes. Refer to the diagram below for specific requirements. • The cabinet is designed for surface m...

Page 5 - Wiring; CLASS 2; Installation Guide – DOC. 6672B

CRESTRON GREEN LIGHT™ Power Switching Wiring NOTE: All wiring must be installed in accordance with all local and national electrical codes. NOTE: Refer to the torque settings specified on pages 6, 7 and 8. CRESTRON GREEN LIGHT cabinets are shipped with GLXP modules installed and prewired to the bran...

Page 7 - installation. The jumper shorts the; SW; Use copper conductors only – rated 75; NEUTRAL; connection is only present on; OUTPUT 1

CRESTRON GREEN LIGHT™ Power Switching Load Wiring (Section B) CAUTION: Bypass jumpers are provided on each output to allow testing and to protect the module during installation. The jumper shorts the L and SW terminals so that the load circuit is energized when the branch breaker is on. Do not remov...

Page 8 - Turn on the circuit breakers.; NET

Power Switching CRESTRON GREEN LIGHT™ The GLXP-DIMFLV8 also requires wiring the terminals for 0-10 VDC control wire. Refer to the following diagram when connecting the dimmable ballast. Each control wire terminal accepts one 12 – 28 AWG wire. 0-10 VDC Control Wiring for GLXP-DIMFLV8 Only TO + ON 4-W...

Page 9 - NET Port Wiring

CRESTRON GREEN LIGHT™ Power Switching Connector Wiring RED WHI T E BLUE BLACK NET: TO CONTROL SYSTEM AND OTHER CRESNET DEVICES POWER: 24 VDC JUMPERED FROM NET PORT or EXTERNAL SUPPLY. PROVIDES CRESNET POWER TO THE MODULES OVERRIDE: FROM DEVICE PROVIDING CONTACT CLOSURE & TO OTHER DEVICES RECEIVI...

Page 10 - EXT; and; POWER; supplied connector as shown in the following diagram.; MODULES; port; PWR; OVERRIDE Port Wiring; OVERRIDE; connector on the bottom of the

Power Switching CRESTRON GREEN LIGHT™ To power the modules externally from a Cresnet 24 VDC power supply, connect the external power supply to the EXT and G pins on the POWER supplied connector as shown in the following diagram. Providing Cresnet Power Externally CRESTRON 24 VDC POWER SUPPLY G 24 Wh...

Page 11 - Testing; Manual Control; Override Mode; Save Override Settings

CRESTRON GREEN LIGHT™ Power Switching Testing Manual Control A lighting module can be manually controlled from its front panel. GLXP-SW and GLXP-HSW Modules: The state of each output can be manually controlled from the front panel. To toggle the output between off and on, tap the appropriate ON/OFF ...

Page 12 - System Operation and Commissioning; must; be performed to ensure system operation.

Power Switching CRESTRON GREEN LIGHT™ System Operation and Commissioning This cabinet has been designed as a component of a programmed Crestron system. System commissioning by an authorized Crestron representative must be performed to ensure system operation. Once the cabinet has been wired and the ...

Page 13 - Problem Solving; TROUBLE; Further Inquiries; to fully benefit from all

CRESTRON GREEN LIGHT™ Power Switching Problem Solving Troubleshooting The following table provides corrective action for possible trouble situations. If further assistance is required, please contact a Crestron customer service representative. Troubleshooting TROUBLE POSSIBLE CAUSE(S) CORRECTIVE ACT...

Page 14 - Appendix A: Setting Module Net IDs; Setup

Power Switching CRESTRON GREEN LIGHT™ Appendix A: Setting Module Net IDs The following procedure will normally be performed by an authorized Crestron representative as part of the System Commissioning phase. For system wiring and basic testing as described on pages 5 and 11, it is not necessary to p...

Page 15 - Appendix B: Module Specifications

CRESTRON GREEN LIGHT™ Power Switching Appendix B: Module Specifications Specifications for the GLXP modules are listed in the following table. GLXP Module Specifications SPECIFICATION GLXP-SW10 GLXP-SW16 GLXP-HSW8 GLXP-HSW12 GLXP-DIMFLV8 Description 10 Channel Switch Module 16 Channel Switch Module ...

Page 16 - Return and Warranty Policies; Merchandise Returns / Repair Service

Power Switching CRESTRON GREEN LIGHT™ Return and Warranty Policies Merchandise Returns / Repair Service 1. No merchandise may be returned for credit, exchange or service without prior authorization from CRESTRON. To obtain warranty service for CRESTRON products, contact an authorized CRESTRON dealer...