Crestron PAC 2 - Manuals

Professional Automation Computer Crestron PAC2 available via Crestron’s single-port C2ENET-1 and dual-port C2ENET-2 Ethernet cards. The PAC2 offers eight programmable analog and digital inputs as well as digital outputs. There are eight normally open relays, isolated with MOV suppression. The 32 Cre...

Crestron PAC2 Professional Automation Computer Specifications Specifications for the PAC2 are provided below. PAC2 2-Series Automation Control System Specifications SPECIFICATION DETAILS CPU 32-Bit Motorola ColdFire ® Processor Processor Speed 257 MIPS (Dhrystone 2.1 Benchmark) On-board Memory 36MB ...

Crestron PAC2 Professional Automation Computer Physical Description The PAC2 automation control system is housed in a gray and black enclosure with labeling on the top and front panels. The dimensions are shown in the illustrations on the next page. PAC2 Physical View without Optional Y and Z Bus Ca...

Professional Automation Computer Crestron PAC2 PAC2 Physical Views 14.00 in (35.56 cm) 7.40 in (18.80 cm) 3.75 in (9.52 cm) Top View Front View Z-Bus Slot Y-Bus Slots Left Side View MEMORY EXPANSION 24 Y Z G 24 Y Z G 24 Y Z G 24 Y Z G 24 Y Z G 24 Y Z G 24 Y Z G 24 Y Z G 24 Y Z G 24 Y Z G 24 Y Z G 24...

Crestron PAC2 Professional Automation Computer Ports/Connectors The ports/connectors provided on the top and front panel of the PAC2 are described in the following paragraphs. LEFT, RIGHT LEFT (24 Y Z G OVERRIDE) RIGHT (OVERRIDE G Z Y 24) These 5-position connectors, rated at 24VDC, 2A maximum load,...

Professional Automation Computer Crestron PAC2 received between the “G” connection and the “L” or “R” connection (R is used in a double-wide enclosure only), the respective left or right column of modules will set the lights to the programmed emergency override state. The connector is rated at 5V, 1...

Crestron PAC2 Professional Automation Computer NOTE: The LAN LEDs are active only if the optional single port or dual port Ethernet card (which is field installed) occupies the Z-BUS slot. LAN A is used for a single port Ethernet card; LAN A and B are used for the dual port card. LNK A, LNK B (LAN) ...

Professional Automation Computer Crestron PAC2 Powering a Hub Segment Pair In the illustration above, one of the supplied 3-pin mini connectors with installed jumper wire is plugged into the POWER 1 port. The PAC 2’s internal power supply is connected to the INT pin; the port’s EXT pin is connected ...

Crestron PAC2 Professional Automation Computer File System Structure TOP LEVEL SECONDARY LEVEL DESCRIPTION \ Root of the file system DISPLAY Legacy directory used in ISYS panels to hold display lists SYS Contains various system configuration files SETUP NAT configuration Web pages HTML Web pages SIM...

Professional Automation Computer Crestron PAC2 Expandable Memory (Compact Flash) The on-board 36MB memory of the 2-Series integrated dual bus control system is enhanced with a 4GB expansion slot that supports off-the-shelf Type II compact flash memory and the IBM Microdrive  hard drive. The slot is...

Crestron PAC2 Professional Automation Computer Setup Mounting the PAC2 in the Crestron Automation Enclosure (CAEN) CAUTION: The CAEN houses equipment that needs to be air-cooled. Therefore, mount in a well-ventilated area. The ambient temperature range must be 32 ° F to 104 ° F (0 ° C to 40 ° C). Th...

Professional Automation Computer Crestron PAC2 Mounting the PAC2 in the CAEN 8B 1/4 inch screw CLX-Series Module PAC2 Double-wide CAEN AC Power Connection The PAC2 requires AC power for operation. This can be accomplished using the materials listed in the following table. This involves adding the te...

Crestron PAC2 Professional Automation Computer PAC2 AC Power Source Assembly and Connection Diagram CRESTRON Rail From HOT From NEUTRAL NEUTRAL To GND Strip HOT To PAC2 Black Terminal Block White Terminal Block Partition Plate End Plate End Bracket 1. Assemble the supplied terminal blocks, partition...

Professional Automation Computer Crestron PAC2 Bussing Strip Installation The PAC2 is supplied with two brass bussing strips to facilitate commoning (linking) of the S5 Relay Output terminal block connections. The bussing strips are constructed with four terminal block positions, and may be trimmed ...

Crestron PAC2 Professional Automation Computer When calculating the wire gauge for a particular network run, the length of the run and the power factor of each network unit to be connected must be taken into consideration. If network units are to be daisy-chained on the run, the power factor of each...

Crestron PAC2 Professional Automation Computer Establishing Communication with the PAC2 Before uploading a program to the control system or performing diagnostic functions, you must connect the control system to the PC. This connection can be serial or (if an optional Z-Bus card is installed) it can...

Professional Automation Computer Crestron PAC2 “Port Settings” Window: Default PC Settings for RS-232 Communication with the PAC2. To verify communication, click Diagnostics | Establish Communications (Find Rack) . This should display a window that gives the COM port and baud rate. TCP/IP Connection...

Crestron PAC2 Professional Automation Computer Once the cable connections are made, open the Crestron Viewport and click Setup | Communication Settings on the menu to display the “Port Settings” window. Then click TCP/IP as the connection type. Enter the IP address of the PAC2. “Port Settings” Windo...

Professional Automation Computer Crestron PAC2 Troubleshooting Communications Use the following checklist if communication cannot be established with the PAC2. 1. Verify that you are using the correct cables. As described previously, an RS-232 connection requires a straight-through serial cable. Tha...

Crestron PAC2 Professional Automation Computer f. Reinitialize the unit by recycling the power or pressing the HW-R button. If the connection is established, the Viewport console should display some text and the PAC2> prompt. g. If communication still cannot be established, contact Crestron custo...

Professional Automation Computer Crestron PAC2 If any errors are generated during programming, they will be displayed in the Messages field. You can double-click a message for more information. Once you have compiled the program files, you are ready to upload them to the control system and user inte...

Crestron PAC2 Professional Automation Computer With TCP/IP, type the IP address of the PAC2. If the panel is connected directly to a COM port on the PC, select Serial as the connection type and check Send directly to touchpanel . To communicate directly to an Ethernet touchpanel, select TCP/IP as th...

Crestron PAC2 Professional Automation Computer As shown on the previous page, click Yes to retrieve the program from Compact Flash, or No to retrieve the program from internal memory. Click Cance l to cancel the operation. When a program is uploaded, that program's filename is added to the New Progr...

Professional Automation Computer Crestron PAC2 2. Select the network ID of the touchpanel, as set in SIMPL Windows and configured on the touchpanel, from the drop-down list. 3. Browse to the HEX or VTZ file to be uploaded. If the file is a HEX file, click Open to begin the transfer. If the file is a...

Crestron PAC2 Professional Automation Computer Send Generic Files-permit you to choose between internal flash and compact flash when selecting programs/files for processing. A new SIMPL Windows command File | Copy Output to Compact Flash copies a compiled SIMPL Windows program (SPZ) file) to a compa...

Professional Automation Computer Crestron PAC2 Console Commands That Work with Compact or Internal Flash The following commands have been modified to enable processing functions for compact flash files/programs: • CD - Permits changing to a directory on compact flash • DELETE - Enables deleting file...

Crestron PAC2 Professional Automation Computer Programming Software You can create a program to control the PAC2 control system using the Crestron programming tools D3 Pro or SIMPL™ Windows ® . Customers whose focus is on lighting systems may prefer to use the D3 Pro software since it is designed es...

Professional Automation Computer Crestron PAC2 PAC2 Device Library Symbols Configuration Manager is where programmers “build” a Crestron control system by selecting hardware from the Device Library . In Configuration Manager, drag the PAC2 from the Control Systems folder of the Device Library to Sys...

Crestron PAC2 Professional Automation Computer Description Internal configuration of a Versiport +5V 2K pullup1 o1 S1-A S1-B A Used for analog input.Can be either a voltagesource or resistive load. VersiPort 1 Digital Output Mode When a Versiport is operating in digital output mode, the output pin w...

Professional Automation Computer Crestron PAC2 Analog Input Mode In analog input mode, the Versiport is typically tied to a resistive load (such as a humidity sensor) or a voltage source (both can be represented by box "A" in the Versiport diagram). When a resistive load is tied to a Versipo...

Crestron PAC2 Professional Automation Computer To add a device to the system, expand the C2 Net-Device slot and double-click the desired Net ID, or right click and select Add Item from the submenu. Then select the device you want to add. Alternatively, you can drag the device from the Cresnet Module...

Professional Automation Computer Crestron PAC2 2. Click Project | Edit Program Header . 3. Click 2-Series in the Target Control System Classes list box (refer to graphic below). You can select other types of control systems as well, but then you will be limited to symbols that are supported by all o...

Crestron PAC2 Professional Automation Computer Problem Solving Problems may occur with the 2-Series automation control system itself or there may be serial communication difficulties with other devices connected to the control system. The next two sections address possible problem solving tools or p...

Professional Automation Computer Crestron PAC2 2. Open Viewport and select Setup | Communication Settings to open the “Port Settings” window. 3. In the window, select RS-232 (Connection Type), 57600 (Baud Rate), N (Parity), 8 (Data Bits) and 1 (Stop Bits) and click OK . 4. Power down the PAC2. 5. Wh...

Professional Automation Computer Crestron PAC2 Further Inquiries If after reviewing this Operations Guide, you cannot locate specific information or have questions, please take advantage of Crestron's award winning customer service team in your area. Dial one of the following numbers. • In the US an...

Crestron PAC2 Professional Automation Computer Software License Agreement This License Agreement (“Agreement”) is a legal contract between you (either an individual or a single business entity) and Crestron Electronics, Inc. (“Crestron”) for software referenced in this guide, which includes computer...

Professional Automation Computer Crestron PAC2 If You are a business or organization, You agree that upon request from Crestron or its authorized agent, You will within thirty (30) days fully document and certify that use of any and all Software at the time of the request is in conformity with Your ...

Crestron PAC2 Professional Automation Computer Return and Warranty Policies Merchandise Returns / Repair Service 1. No merchandise may be returned for credit, exchange, or service without prior authorization from CRESTRON. To obtain warranty service for CRESTRON products, contact the factory and req...

Crestron Electronics, Inc. Operations Guide – DOC. 5941 15 Volvo Drive Rockleigh, NJ 07647 12.02 Tel: 888.CRESTRON Fax: 201.767.7576 Specifications subject to www.crestron.com change without notice.