Crestron CP2 - Manuals

2-Series Integrated Control Processor Crestron CP2/CP2E bit Motorola ColdFire  processor. The 2-Series operating system is vastly upgraded from Crestron’s X-generation products, yet compatible with existing Crestron software and programming. A key feature is the new Crestron Compiler, which allows ...

Crestron CP2/CP2E 2-Series Integrated Control Processor Physical Description The CP2/CP2E integrated control systems are housed in black enclosures with labeling on the front and rear panels. The front panels of both units include standard LEDs and two reset buttons. All connections to the units are...

2-Series Integrated Control Processor Crestron CP2/CP2E Controls and Indicators The CP2/CP2E front panel indicators and controls are described below. PWR (Power) This LED illuminates when the unit is connected to and receives 24VDC power from an AC power pack or the Cresnet NET connector. NET This L...

Crestron CP2/CP2E 2-Series Integrated Control Processor NOTE: The orientation of this connector is “upside down” compared to other Crestron network devices (e.g., CNX-BIPAD8, CNX-RMCLV). Be sure the mating Cresnet cable connector is properly aligned before attempting to insert it, to avoid damage to...

2-Series Integrated Control Processor Crestron CP2/CP2E COM Pinout to RS-485 Bus COM (DB9) CONNECTOR RS-485 BUS Tie Pins 1 & 9 - Tie Pins 4 & 6 + Pin 5 G INFRARED – SERIAL OUTPUT A B C D E F G H S G S G S G S G INFRARED - SERIAL OUTPUT S G S G S G S G These connectors provide eight serial ou...

Crestron CP2/CP2E 2-Series Integrated Control Processor 24VDC, 2.0A (Power Supply) 2 4 V D C 2.0A This male connector can be used to supply 24VDC power to the CP2/CP2E from an AC power pack purchased separately. (Refer to Optional Power Supply on page 13). When power is supplied to the units through...

2-Series Integrated Control Processor Crestron CP2/CP2E series control engine. Non-volatile memory contains information that is retained after loss of electrical power. Volatile memory is lost after a power failure. Refer to the lists below for a breakdown of memory usage for program-related informa...

Crestron CP2/CP2E 2-Series Integrated Control Processor DRAM DRAM is used by the operating system for dynamic storage of variables, signals and other constructs used at runtime. The actual amount of DRAM used at any given time depends on the particular program that is running, i.e., usage is variabl...

2-Series Integrated Control Processor Crestron CP2/CP2E Ear Attachment for Rack Mounting (CP2E shown in illustration) 1. Using a Phillips screwdriver, remove and retain the three side screws closest to the front panel. 2. Position a rack ear so that its mounting holes align with the vacated holes, a...

Crestron CP2/CP2E 2-Series Integrated Control Processor 5. Secure the wires connected to the terminal block with a tie wrap around the bussing strip to provide strain relief. Network Wiring NOTE: When making wire connections, refer to the latest revision of the Cresnet Network Interconnect Drawing (...

2-Series Integrated Control Processor Crestron CP2/CP2E Wire Gauge Values RESISTANCE (R) WIRE GAUGE 4 16 6 18 10 20 15 22 13 Doubled CAT5 8.7 Tripled CAT5 NOTE: When daisy-chaining Cresnet units, strip the ends of the wires carefully to avoid nicking the conductors. Twist together the ends of the wi...

Crestron CP2/CP2E 2-Series Integrated Control Processor Optional Power Supply The units can be powered through the NET network connector, or by an optional AC power pack (purchased separately). If an external power supply is to be used, Crestron recommends its CNPWS-75 External Power Supply or PW-24...

2-Series Integrated Control Processor Crestron CP2/CP2E Slot 1: C2Net-Device The C2Net-Device slot enables the CP2 and CP2E to control up to 252 Cresnet devices. Each Cresnet device is assigned a unique identifier called a Net ID, which is a hexadecimal value ranging from 03 to FE. To view the list ...

Crestron CP2/CP2E 2-Series Integrated Control Processor Slot 3: C2I-IO8 The CP2 and CP2E provide eight I/O ports called Versiports, each of which can function as a digital input, a digital output, or an analog input. Each Versiport has a corresponding pullup resistor. In Program Manager, drag the C2...

2-Series Integrated Control Processor Crestron CP2/CP2E Driving the corresponding <pu-disable> signal high can modify this behavior. This is not recommended, though, since it will cause the output pin to float when < o > goes low. Example 1 (recommended): The < pu-disable1 > signal...

Crestron CP2/CP2E 2-Series Integrated Control Processor A voltage source is placed on Versiport 1 and < MinChange1 > is set to 10 via an Analog Initialize symbol. The value of < i1 > will not be propagated until it changes by at least 10. If the current value is 500, then a new value wil...

Crestron CP2/CP2E 2-Series Integrated Control Processor If the program contains SIMPL+ or User modules, the conversion might generate error messages. This is because modules and programs often contain symbols with “ambiguous” signals. For example, the inputs of the Serial to Analog symbol can be def...

2-Series Integrated Control Processor Crestron CP2/CP2E Module Header Information After you convert each module in a program, you can convert the program as described previously: drag the CP2 or CP2E onto the existing control system in System Views and click Yes to confirm the replacement. For furth...

Crestron CP2/CP2E 2-Series Integrated Control Processor • Hardware handshaking (RTS/CTS) enabled. • Software handshaking (XON/XOFF) not enabled. “Port Settings” dialog box: Default PC settings for RS-232 communication with the CP2/CP2E. To verify communication, click Diagnostics | Establish Communic...

2-Series Integrated Control Processor Crestron CP2/CP2E use a CAT5 crossover cable to connect the two LAN ports directly, without using a hub. Once the cable connections are made, open the Crestron Viewport and click Setup | Communication Settings on the menu to display the “Port Settings” dialog bo...

Crestron CP2/CP2E 2-Series Integrated Control Processor some may be internal (e.g., for a modem). Consult the manufacturer’s documentation for further information about the COM ports on your PC. 3. Check the ERR LED indicator on the front panel of the CP2/CP2E. If this LED is illuminated, unplug the...

2-Series Integrated Control Processor Crestron CP2/CP2E Compiling and Uploading a Program to the Control System After you have completed your SIMPL Windows program you must compile and upload the program to the control system. To compile the program, simply click the Convert/Compile button on the SI...

Crestron CP2/CP2E 2-Series Integrated Control Processor Another way to verify that the program has been transferred successfully is to select Report Program Information on the Viewport Functions menu. Program information is also displayed in the Viewport console whenever power is removed and re-appl...

2-Series Integrated Control Processor Crestron CP2/CP2E Uploading Touchpanel Projects via the CP2/CP2E You can use a connection to the CP2 or CP2E to upload VisionTools Pro-e projects to any Cresnet touchpanel. Compiled projects for TPS panels are contained in VTZ files; projects for all other touch...

Crestron CP2/CP2E 2-Series Integrated Control Processor 3. After the transfer is complete, the CP2/CP2E will automatically reboot. To confirm the transfer, click Diagnostics | Check Ops Version . The Viewport console should display the new .cuz version number. Advanced Console Commands The SIMPL Win...

2-Series Integrated Control Processor Crestron CP2/CP2E Troubleshooting The table below and on the next page provides corrective action for possible trouble situations. If further assistance is required, please contact a Crestron customer service representative. CP2/CP2E Troubleshooting TROUBLE POSS...

Crestron CP2/CP2E 2-Series Integrated Control Processor Battery Replacement A Lithium battery is used to power the system clock within the CP2/CP2E. Under normal conditions, it will last for approximately 10 years. In the event that the clock fails, only an authorized technician should replace it. R...

2-Series Integrated Control Processor Crestron CP2/CP2E Passthrough Mode Dialog Box The PC will now be communicating directly with the device. To exit Passthrough mode, simply click Functions | Exit Passthrough Mode . A system reboot will also exit Passthrough mode. 30 • 2-Series Integrated Control ...

Crestron CP2/CP2E 2-Series Integrated Control Processor Further Inquiries If after reviewing this Operations Guide, you cannot locate specific information or have questions, please take advantage of Crestron's award winning customer service team by calling: • In the US and Canada, call Crestron's co...

2-Series Integrated Control Processor Crestron CP2/CP2E Software License Agreement This License Agreement (“Agreement”) is a legal contract between you (either an individual or a single business entity) and Crestron Electronics, Inc. (“Crestron”) for software referenced in this guide, which includes...

Crestron CP2/CP2E 2-Series Integrated Control Processor If You are a business or organization, You agree that upon request from Crestron or its authorized agent, You will within thirty (30) days fully document and certify that use of any and all Software at the time of the request is in conformity w...

2-Series Integrated Control Processor Crestron CP2/CP2E Return and Warranty Policies Merchandise Returns / Repair Service 1. No merchandise may be returned for credit, exchange, or service without prior authorization from CRESTRON. To obtain warranty service for CRESTRON products, contact the factor...

Crestron CP2/CP2E 2-Series Integrated Control Processor This page intentionally left blank. Operations Guide - DOC. 5980 2-Series Integrated Control Processor: CP2/CP2E • 35

Crestron Electronics, Inc. Operations Guide – DOC. 5980 15 Volvo Drive Rockleigh, NJ 07647 02.02 Tel: 888.CRESTRON Fax: 201.767.7576 Specifications subject to www.crestron.com change without notice.