COZY 78111 - Manuals

COMBUSTION AND VENTILATION AIR When installed, this gas appliance must be provided with freshair for combustion, ventilation, and dilution of hot flue gases.The minimum required volume of the area where the appliance isinstalled should be 50 cubic feet per 1,000 btu/hr. If installed in an area of th...

LOCATION AND SPECIAL PRECAUTIONS The wall furnace should be located near the center ofthe house for best heat distribution. If the area where the appliance is to be installed containscarpeting, tile or combustible materials, other than woodflooring, the appliance shall be installed on a metal plate,...

INSTALLATION / WHEN RECESSED (UP TO 9-1/4”) STEP 1 . Cut out floor plate between 2x4 studs, so heater will set flat on floor. STEP 2 . Make electrical connection of 115 V. wiring into junction box provided on top of header plate. STEP 3. Attach the base plate (purchased with the vent pipe)to the hea...

Installation of B-W Gas Ventfor one-story buildings or forfirst floor of multi-storybuildings. Ceiling plate spacers to centerB-W Gas Vent in stud space -nail securely at both ends. Plate cut away for fullwidth of stud space toprovide ventilation. Studs on16 inch centers Sheet metal screw baseplate ...

CF353C-H, CF354C-H, CF503C-H, CF504C-H, CF653C-H, CF654C-H STANDING PILOT FOR YOUR SAFETY READ BEFORE LIGHTING WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life. A. This appliance has a pilot, which must ...

TERMINAL BLOCK WIRING DIAGRAM CAUTION: Label all wires prior to disconnection when servicing controls. Wiring errors can cause improperand dangerous operation. Verify proper operation after servicing. AUXILIARY LIMIT SWITCH For your safety this furnace is equipped with a manual reset auxiliary limit...

CF353C-H, CF354C-H STANDING PILOT CF503/504C-H, CF653/654C-H Page 14 CF353C-H,CF354C-HPICTORIALSCHEMATIC Thermostat PowerCord Black Black Green White White Black Black Black White Black Black Brown Blue Black T r a n s f o r m e r Motor SpillSwitch LimitSwitch FanSwitch Brown Blue Black T H T R GasV...

CF357C-H, CF358C-H I.I.D. CF557C-H, CF558C-H Page 15 BLACK BLACK BLACK AUXILIARYLIMIT SWITCH SPILLSWITCH PILOT IGNITION MODULE MV/PV GAS VALVE LIMITSWITCH FANSWITCH SELECTORSWITCHBLACK BROWN BLUE TRANSFORMER MOTOR WHITE BLACK BLACK BROWN BLACK GREEN WHITE WHITE BLACK THERMOSTAT POWERCORD RED RED GRE...

ROUGH-INS FOR REAR OR SIDE DISCHARGE Install plastergrounds as shown in Figure 12 and Figure 13. NOTE: When side discharge is being used, furnace should be set exactly 4” from side wall. 14-3/8” 10-3/ 16” PlasterGround SIDE FIGURE 13 REAR FIGURE 12 OPTIONAL ACCESSORY KITS REAR REGISTER KIT (Flush Mo...

SIDE DISCHARGE ON CASING 1. Use optional kit No. 306SR-A. 2. Cut out and remove embossed area on casing side. 3. Remove knockout from inner liner. 4. Place 1-1/2” boot from kit through opening, matchingflanges of boot to knockout on inner boot. 5. Mark screw holes and remove boot. 6. Drill holes wit...

SYMPTOM POSSIBLE CAUSES CORRECTIVE ACTION Flame too large 1. Defective operator section of gas valve. 1. Replace complete valve. 2. Burner orifice too large. 2. Check with local gas company for proper orifice size and replace. 3. If installed above 2,000 ft. 3. Refer to orifice chart on Page 9. Nois...

SYMPTOM POSSIBLE CAUSES CORRECTIVE ACTION Pilot won’t light, 1. Air in line. 1. Bleed line. or stay lit 2. Defective thermocouple. 2. Replace thermocouple. (STANDING PILOT) 3. Pilot flame too low. 3. Adjust pilot flame. 4. Manual reset switch not engaged. 4. Push on button. Pilot won’t light, 1. Spa...

REV. 03/05 COUNTERFLOW WALL FURNACE / STANDING PILOT Prices and specifications subject tochange without notice. Allprices are F.O.B. factory. MODELS: NAT. GAS L.P. GAS CF353C-H CF354C-H CF503C-H CF504C-H CF653C-H CF654C-H CONTROL ASSEMBLY Page 20 26 24 14 25 34 5 10 11 4 27 29 28 12 30 13 35 1f 31 1...

Page 21 * REQUIRES TWO REV. 03/2005MARCH 2009 HOW TO PROPERLY ORDER PARTS : In addition to part description and part number, please give model number, serial number, and type of gas used. This information can be found on the rating plate that is attached to heater. N A T U RA L M O D E L N U M BE R ...

HOW TO PROPERLY ORDER PARTS: In addition to part description and part number, please give model number, serial number, and type of gas used. This information can be found on the rating plate that is attached to heater. Page 23 *REQUIRES TWO REV. 03/2005MARCH 2009 N A T U R A L M O D E L N U M B E R ...

IMPORTANT SAFETY BULLETIN ON YOUR GAS CONTROL AND PILOT LIGHT SYSTEM FOR HEATING EQUIPMENT WHAT YOU DON’T KNOW CAN HURT YOU. Your pilot light system has been designed for safe and reliable operation. Although safety mechanisms are built-in,the potential for hazard exists. This information is intende...

L I M I T E D W A R R A N T Y The Louisville Tin & Stove Co. warrants to the original user the accompanying product for the period specified herein, provided said product is installed, operated, maintained, serviced, and used according to the instructions and specifications accompanying the prod...