Conair CL-79 - Manuals

CONAIR 0 5 - 1 5 - 9 6 7 9 5 3. Functional description 3.1 Overview 79 granulators are designed for grinding different types of plastic waste. The granulator is controlled from an electrical cabinet with a start/stop functionand an emergency stop button. The material is fed into the hopper (A) and f...

CONAIR 0 5 - 1 5 - 9 6 7 9 6 3.2 Safety system Since there are rotating knives inside the granulator, there is a built-in safetysystem to prevent personal injury. Emergency stop: The equipment is fitted with an emergency stop switch on theelectrical cabinet. The emergency stop is activated by pushin...

CONAIR 0 5 - 1 5 - 9 6 7 9 7 4. Safety regulations 4.1 Overview The granulator is equipped with safety switches to prevent the front door andthe hopper from being opened during operation. The following safety measures should always be observed when handling thegranulator: • Always switch off the pow...

CONAIR 0 5 - 1 5 - 9 6 7 9 8 5. Installation All instructions must be carried out in the order described, to prevent personalinjury or damage to machinery. Always take great care when handling the knives since they arevery sharp and can cause personal injury. The granulator should be connected to th...

CONAIR 0 5 - 1 5 - 9 6 7 9 9 5.3 Electrical connection The granulator should be connected up by an authorised electrician. • Connect the granulator to the mains supply. See Electrical scheme, chapter9, connecting (Q1). Check the granulator motor’s rotation direction as follows: • Set the main circui...

CONAIR 0 5 - 1 5 - 9 6 7 9 10 6. Operation and daily maintenance 6.1 Starting and stopping The start and stop functions are controlled by a change-over button on theelectrical cabinet. NOTE: The granulator should not be stopped until it has finished grinding allthe material in the hopper and cutter ...

CONAIR 0 5 - 1 5 - 9 6 7 9 11 6.4 Trouble-shooting 6.4.1 If the granulator does not start • Check that the saftey switches’ break screws are turned fully clockwise. It isnot possible to start the granulator unless the break screws are screwed in. • Check that the emergency stop is not activated. It ...

CONAIR 0 5 - 1 5 - 9 6 7 9 12 7. Servicing All servicing work should be carried out by a qualified service engineer and inthe order described, to prevent personal injury or damage to machinery. 7.1 Changing the knives When changing the knives, also check for any wear to the screen. For safetyreasons...

CONAIR 0 5 - 1 5 - 9 6 7 9 13 Assembling the rotating knives 1. Clean the cutter's knife location and place a rotating knife in the knife location. 2. Fasten the screws (A) together with the washers (H) and tighten gently. 3. Adjust the knife using the setting screws (B) to give the correctamount of...

CONAIR 0 5 - 1 5 - 9 6 7 9 14 7.2 Sharpening the knives Always take great care when sharpening the knives since theyare very sharp and can cause personal injury. 7.2.1 Overview NOTE: Use the services of a skilled person when re-sharpening the knivesand only sharpen the edges marked with the special ...

CONAIR 0 5 - 1 5 - 9 6 7 9 16 7.3 Inspecting and adjusting the belts The V-belts must be inspected after 30 hours’ operation. • Loosen and remove the outer plateon the belt guard. • Load one of the V-belts between therotor pulley and the motor pulleywith 25 N in the middle of and at aright angle to ...

CONAIR 0 5 - 1 5 - 9 6 7 9 17 7.5 Rotor pulley, assembling/disassembling 7.5.1 Rotor pulley Disassembling 1. Loosen all screws a few turns. 2. Unscrew two of the screws. 3. Lubricate both screws and screw them into the disassembling holes (A). 4. Tighten both disassembling screws alternately until t...

CONAIR 0 5 - 1 5 - 9 6 7 9 18 8. Spare parts list 8.1 Overview Page 8.1.1 79, Cutter housing .......................................................... 19-21 8.1.2 79 ...................................................................................... 22 8.1.3 79, ....................................

CONAIR 0 5 - 1 5 - 9 6 7 9 26 8.1.6 Pause/pulse relay when emptying with air veyor In those cases when emptying of the granule bin with an air veyor has beenchosen, the pause/pulse relay should be cancelled to prevent a glut in thegranule bin. When delivered, the relay is presetas follows: T1 = rang...

CONAIR 0 5 - 1 5 - 9 6 7 9 28 10. Layout 10.1 Dimensions Page 10.1.1 79 ................................................... 28 10.1.2 79 .................................................... 29 10.1.3 79 .................................................... 30 10.1.4 79 ..................................

CONAIR 0 5 - 1 5 - 9 6 7 9 33 11.1.1 79, all models: Third fixed knife, disassembling/ assembling Pos. Qty. Part no. 1 1 1-19022 2 1 2-17732 3 1 2-17733 4 2 9-40106 5 2 9-40302 6 1 3-19021 7 2 9-40075 8a 2 9-50086 8b 2 9-50214 9 2 9-40050 Disassembling 1. Unscrew the screws (4) and release the ruler...

CONAIR 0 5 - 1 5 - 9 6 7 9 35 11.1.3 79, Hopper with band conveyor Disassembling/Assembling the band conveyor Disassembling 1. Release the fastening screw (A). This is done most easily by unscrewing thenut on the under side. The vibrationabsorber is then released. 2. Release the hood over the screw ...

CONAIR 0 5 - 1 5 - 9 6 7 9 36 12. Transporting and storing 12.1 Overview Handling and transporting of the machinery should be carried out by speciallytrained personnel. The machine is packed in weather-proof and partly shock-proof plastic sheeting.It is fixed with straps to a pallet for transportati...