Clover CDR1650 - Manuals

Contents 7 8-4.9.1. Terminal mode....................................................................................................................... 150 8-4.9.2. Multi mode...............................................................................................................................

9 About this manual This is the Instruction Manual for Stand-alone type DVR model CDR1650 . This Manual describes how to install and operate the Stand-Alone DVR and provides specifications and features. Please read this manual thoroughly and follow the installation process before using Stand- alone ...

11 1. Unpacking Care should be taken when unpacking to avoid damaging the unit. Please check that the following items are included: ▶ Stand-alone DVR unit ▶ All Accessories : Bracket, Power Cable, Screws ▶ Remote Controller & Battery ▶ PS2 Mouse ▶ DSUB 26p Connector (Sensor Input, Relay Output S...

13 2. Features ▶ Multi Functional Record - Powerful, multiple Record Modes available: Manual (Continuous), Timer, and Motion Detection Recording. ▶ User friendly GUI - A few simple buttons for Easy control. ▶ Automatic System Recovery - Automatic and Complete System recovery within 10 seconds. ▶ Eas...

15 3. What to do at the time of Installation Stand-alone DVR should be installed in the following order; 1. Make sure all the required hardware is available. - Stand-alone DVR unit (including HDD) - Up to 16 cameras (including power source) - CCTV or VGA monitor (or TV set) - Network cable if connec...

17 4. Specifications [Fig 4-1 Specifications] Design and the specifications are subject to change without notice. 4 IT E M T e le v is io n S y s te m N T S C P A L R e fre s h R a te 6 0 fie ld s /s e c 5 0 fie ld s /s e c V id e o R e s o lu tio n 7 2 0 x4 8 0 7 2 0 x5 7 6 V id e o In p u tsV id e...

5. Installation 19 5. Installation CONTENTS 5-1. C ONTROLS AND C ONNECTORS (F OR 8C H & 16C H DVR)........................................................ 20 5-2. N OTE FOR I NSTALLATION ...................................................................................................... 22 5-3...

5. Installation 21 - B z Rear a. Display (Full / Split) b. Emergency Record c. Zoom d. Quick Replay e. OSD On/Off f. Audio g. Stop (ESC) h. PTZ CAMERA INPUT VOLTAGE SELECT POWER INLET RS-422C PORT USB PORT ETHERNET PORT SENSOR IN/OUT VGA SPEAKER AUDIO INPUT LOOP OUT INPUT MAIN VIDEO INPUT AUX VIDEO ...

Stand-alone DVR Instruction Manual 22 5-2. Note for Installation ‹ Install the system according to the instructions described in this manual. ‹ This product is designed for indoor use and should not be used outdoors. ‹ Avoid any area with high humidity or dust which can shorten lifetime of the unit....

Stand-alone DVR Instruction Manual 24 5-4. Installation 5-4.1. Camera Connection ▫ Connection of Normal Cameras Connect the cameras to the Video Input (BNC connector) on the back of the unit as shown above [Fig. 5-3 System Connection]. ▫ Connection of Loop Output The Camera or video output is availa...

5. Installation 27 ▫ RELAY OUT Connection When necessary, use RELAY OUT. The Output of RELAY OUT is a relay contactor type and supports N.O. (Normal Open) & N.C. (Normal Close). The Output capacity is 220V 1A. A higher capacity can cause system failure. [Fig 5-6 RELAY OUT Connection]

5. Installation 29 5-4.5 Connection to an Ethernet Network ▫ Connecting the cable to Ethernet. Our Ethernet connector is a RJ45 type. The maximum cable length is 300 ft. When you want to use a longer cable, we suggest using repeater. [Fig 5-9]

Stand-alone DVR Instruction Manual 30 5-4.6. POWER CONNECTION Select proper voltage (see fig 5-10) and connect to a reliable power source. It should not be shared with other electrical equipment on the same line. Poor performance can occur if the connected voltage is more than 10% plus or minus the ...

31 6. How to operate CONTENTS 6-1. G ENERAL I NFORMATION ....................................................................................................... 33 6-2. O PERATING I NTERFACE ........................................................................................................ 34 6...

6. How to Operate 33 6-1. General Information ▫ You can operate all functions of the system by use of buttons located on the front panel, remote controller and a mouse. Additionally, you can remotely control this unit via RS422C or the Ethernet port located on the back of the unit. ▫ System status i...

6. How to Operate 37 6-4.3. APPEARANCE OR DISAPPEARANCE OF POWER BUTTON The Power On/Off button and the Audio buttons (See section 6-7.4) as shown in Fig.6-3-1 will always stay on the MENU bar when the system is not connected through the DVR Master (Client Host Program or Internet Explorer). But the...

Stand-alone DVR Instruction Manual 42 6-7.3. SEQUENCING SCREENS ▫ Displaying the cameras in SEQUENCE is available in the LIVE mode or the RECORD mode. Each of the channels will be displayed in sequence and the dwell time can be adjusted in the camera set up menu (Refer to section 7-4.7). ▫ This ICON...

Stand-alone DVR Instruction Manual 44 6-7.5. ZOOM The image on the screen will be zoomed up to 2 times when the ZOOM button is clicked in the LIVE mode (This function is available on the full screen mode only). ▫ Click the ZOOM button on the MENU bar in the LIVE mode. ▫ Move the mouse on the ZOOMED ...

6. How to Operate 45 6-7.6. OSD ON / OFF OSD ON /OFF is possible in the LIVE mode or RECORD mode. ▫ Click the OSD button on the MENU bar to turn the OSD (On Screen Display) ON or OFF. When the OSD is in OFF position, all the texts on the screen will be disappeared. [Fig.6-11 OSD ON SCREEN] 2007/05/2...

Stand-alone DVR Instruction Manual 46 6-7.7. PAN / TILT ▫ Click the PAN/TILT button on the MENU bar in the LIVE mode to access the PAN/TILT cameras. ▫ Click the (EXIT) button to return to the LIVE mode. [Fig.6-13 PAN/TILT button] [Fig.6-14 PAN/TILT window]

6. How to Operate 47 ▫ Channel Selection and Screen Conversion To change a channel, press the CHANNEL button on the front panel or click the CHANNEL button on the [Fig.6-15 PAN /TILT CONTROL window]. It will be converted a full screen. To return to the LIVE mode, press the SPLIT button on the front ...

Stand-alone DVR Instruction Manual 48 ▫ PRESET [Fig.6-15-1 Preset Menu] It is a function to preset the PTZ camera(s) which you wish to monitor frequently. Preset Setup - Select a position of camera you wish to preset and click the SET button in Fig.6-15-1. - Click the number(s) for the current posit...

Stand-alone DVR Instruction Manual 54 6-8. Record This system provides Watchdog function. When power goes off during recording and the power turns on, the system will automatically start recording. 6-8.1. Manual (Continuous) recording ▫ Click the SETUP icon on the MENU bar in the LIVE mode. ▫ Click ...

Stand-alone DVR Instruction Manual 56 6-8.4. Timer Event Recording ▫ Click the SETUP icon on the MENU bar in the LIVE mode. ▫ Click the RECORD button in the SETUP menu and the RECORD window will be displayed. ▫ Select the TIMER RECORDING ( ) between the MANUAL RECORDING ( ) and the TIMER RECORDING (...

6. How to Operate 57 6-8.5. Recording Icons The Recording Icons depends on recording modes are displayed in the upper left hand corner of the screen. ▫ To turn the Recording Icon OFF, click the DISPLAY ON in the RECORD menu and then it will be turned OFF. You can select the value ON or OFF by repeat...

Stand-alone DVR Instruction Manual 58 6-9. REPLAY 6-9.1. QUICK REPLAY It is available only by pressing the PLAY button on the front panel or the QICK SEARCH button on the remote controller. ▫ Press the PLAY button, then the recent recorded list will be played. 6-9.2. REPLAY ▫ Click the REPLAY icon o...

6. How to Operate 59 6-9.2.1. Playback Devices In order to payback, plug the USB devices such as external USB HDD, USB memory to the USB port or insert a recorded media (CD-R/W or DVD-R/W) into the DVD-R/W drive. When the devices are ready to playback, the Ready on the corresponding devices will be ...

Stand-alone DVR Instruction Manual 60 ▫ Select the hour on the Start Time Select Window (See Fig.6-32) by clicking the mouse on the Hour (0 – 23 hour) you wish to start to play. The green active buttons indicate the HOUR that contains recorded data, and the red active buttons indicate the selected S...

6. How to Operate 61 6-9.2.3. Replaying Replaying start time set-up can be possible within a recording time extent. ▫ Replay buttons (NORMAL / MOTION / SENSOR) NORMAL PLAY: Click the button to play all the recorded data. MOTION PLAY: Click the button to play the recorded data by MOTION only. SENSOR ...

6. How to Operate 65 6-10. COPY ▫ Click the COPY icon on the MENU bar, and then the COPY window as shown in Fig.6-38 will be displayed. ▫ Click the (EXIT) button to return to the previous mode. 6-10.1. Copying devices In order to copy the recorded data, plug the USB devices such as external USB HDD,...

6. How to Operate 69 6-10.4. Copying the recorded data during replaying The system, CDR1650 allows users to copy the recorded data during replaying. ▫ Start replaying (See section 6-9). ▫ Right-click on the replaying screen, and the COPY DATA screen will be displayed (See Fig.6-43). ▫ To set the sta...

73 7. SETUP CONTENTS 7-1. SETUP .............................................................................................................................. 76 7-2. SYSTEM ........................................................................................................................... 77...

Stand-alone DVR Instruction Manual 78 7-2.1. TIME / DATE ▫ Click the “TIME/DATE” button in the SYSTEM menu, and then the TIME/DATE menu will be displayed (See Fig.7-4). ▫ Click the “EXIT” button to return to the SYSTEM menu. ▫ TIME FORMAT Click the mouse on the TIME FORMAT button to change and then ...

Stand-alone DVR Instruction Manual 80 7-2.2. SYSTEM CONFIG ▫ Click the “SYSTEM CONFIG” button in the SYSTEM menu, and then the SYSTEM CONFIG menu will be displayed (See Fig.7-10). ▫ Click the “EXIT” button to return to the SYSTEM menu. 7-2.2.1. FACTORY DEFAULT ▫ Click the “ FACTORY DEFAULT ” button ...

Stand-alone DVR Instruction Manual 82 ▫ BACKUP CONFIG This function is to save the current settings to load the settings to the system. Save the current settings in the BACKUP CONFIG in order to load it to the system in the near future whenever you need to change the settings. - Click the BACKUP CON...

7. Setup 83 7-2.3. PASSWORD ▫ ON/OFF Select ON or OFF by clicking the mouse. If the ON is selected, the password has to be entered to get into the SETUP mode, RECORD mode, COPY mode, REPLAY mode, and when trying to connect the network through the DVR Master . ▫ PASSWORD CHANGE Click the password “**...

Stand-alone DVR Instruction Manual 84 7-2.4. IR REMOTE ID Up to 16 DVR systems can be controlled by only one remote controller we provided, but IDs should be assigned on each of the systems. You don’t have to assign any ID on the single unit and you can control the system with the provided remote co...

Stand-alone DVR Instruction Manual 92 7-4.5. Pan/Tilt Settings ▫ Click the PAN/TILT button on the corresponding channels in the CAMERA menu, then the PAN/TILT window will be displayed as shown in Fig.7-33. ▫ Click the (EXIT) button to return to the CAMERA menu. ▫ PTZ ID - Click the PTZ ID button in ...

Stand-alone DVR Instruction Manual 94 ▫ Baud rate Click the “BAUD RATE” button in the PAN/TILT window and choose a value among 1200bps, 2400bps, 4800bps, 9600bps, 19200bps, 38400bps, 57600bps and 115200bps on the Baud Rate pop-up window by clicking the mouse. ▫ Data Bits Click the “DATA BITS” button...

7. Setup 99 7-6.2. All Manual / Timer recording button ▫ Click the All Manual / Timer recording button in the RECORD menu, then the All Manual / Timer recording button will be displayed as shown in Fig.7-55. ▫ Select the Manual Recording button or Timer Recording button for all the channels by click...

Stand-alone DVR Instruction Manual 100 7-6.3. All Motion ON / OFF, Sensitivity and Velocity Setting ▫ Click the button in the RECORD menu, then the ALL MOTION setup pop-up window will be displayed as shown in Fig.7-57. ▫ By clicking the mouse, select the on the pop-up window (See Fig.7-57) to enable...

Stand-alone DVR Instruction Manual 102 7-6.6. Recording Speed ▫ Click the F/S (Frames Per Seconds: Recording Speed) button on each of the channels in the RECORD menu, then the Recording Speed pop-up window will be displayed as shown in Fig.7-64. ▫ Select one of the Recording Speed among AUTO, 30, 15...

7. Setup 103 30 25 15 12 10 8 7.5 6 5 5 3 3 2 2 1 1 NTSC OFF PAL OFF 7-6.7. Recording Quality ▫ Click the QUALITY button on each of the channels in the RECORD menu, then the QUALITY pop-up window will be displayed as shown in Fig.7-67. ▫ Select one of the Recording Quality among LOW, NORMAL, HIGH an...

Stand-alone DVR Instruction Manual 104 7-6.8. Recording Mode The factory default setting for Recording is the Manual Recording (or called Continuous Recording), which keeps recording continuously if the OVERWRITE is set ON in the DISK MANAGE menu. This Manual Recording mode is not only one of the mo...

Stand-alone DVR Instruction Manual 106 ▫ Pre-Alarm Time Setup Allows you to record a section of video just prior to Motion or Sensor activation. Click the mouse on the PRE in the MOTION menu and choose one of the values among 0, 1, 2, 3, 4 and 5 seconds with the mouse’s wheel, and then click it to s...

7. Setup 107 ▫ Spot Setup If the “ON” is selected by clicking the mouse on the SPOT button in the MOTION menu, a full screen will display when a motion is detected. If the “OFF” is selected, the full screen won’t be displayed even though motion of objects is detected. ▫ Region The Motion Detection A...

Stand-alone DVR Instruction Manual 108 - All Clear Click the ALL CLEAR button in the MOTION menu in order to clear the Motion Detection Area, and then the window turns to white color as shown in Fig.7-77. Right-click on the current window to return to the MOTION menu. [Fig.7-76 ALL CLEAR button] [Fi...

7. Setup 109 By Window Set Click the WINDOW SET button in the MOTION menu on each of the cameras and click one of cells (330 cells in total) for the starting point of the area which you would like to designate, and then click the other one of cells for the ending point of area until the motion detec...

Stand-alone DVR Instruction Manual 110 - Window Clear Click the WINDOW CLEAR button in the MOTION menu in order to clear the Motion Detection Area, and then the window you already created the motion detection area will be displayed. Click the starting point and the ending point as much as you wish t...

7. Setup 111 By Each Cell Click the EACH CELL button in the MOTION menu on each of the cameras and click the mouse on each of the cells as much as you would like to designate the Motion Detection Area. To clear, click the designated cells. Right-click on the current window to return to the MOTION me...

Stand-alone DVR Instruction Manual 112 ▫ Map View Click the MAP VIEW button in the MOTION menu to view the current settings for Motion detection area. Right-click on the current window to return to the MOTION menu. Note : Please pay attention to the following directions in order to use the Motion De...

Stand-alone DVR Instruction Manual 116 7-7. NETWORK ▫ Click the “NETWORK” button in the SETUP menu and then the NETWORK menu will be displayed on the screen as shown in Fig.7-92. ▫ Click the (EXIT) button to return to the SETUP menu. 7-7.1. IP Mode When the system uses the same IP address every time...

Stand-alone DVR Instruction Manual 118 7-7.3. Port ▫ PORT is the TCP address of the program, which is used to connect to the network viewer. It can be set from 1 to 65535 values. ▫ Click the PORT button and then the On Screen Keyboard will show up. ▫ Delete the current port number with the button an...

7. Setup 121 7-7.6. DDNS (DYNAMIC DOMAIN NAME SYSTEM) ▫ Select the DDNS button in the NETWORK menu by clicking the mouse, pressing the buttons on the front panel or remote controller. The DDNS menu will show up as shown in Fig.7-103. ▫ To return to the NETWORK menu, Click the (EXIT) button. ▫ If you...

Stand-alone DVR Instruction Manual 122 ▫ HOST NAME - Click the HOST NAME in the DDNS menu and type the HOST NAME registered to the DDNS server such as DYNDNS.ORG and NO-IP.ORG by using the On Screen Keyboard. - After changing the values, click on the OK button. ▫ USER ID - Click the USER ID in the D...

7. Setup 123 7-7.7. HOW TO SETUP AND USE THE DDNS 7-7.7.1. Router. It has to be set as a virtual server (or port forwarding) in order to utilize the DDNS. There are a lot of manufacturers on the market. Please read the provided manual thoroughly before setting or visit our website at www.cloverusa.c...

Stand-alone DVR Instruction Manual 126 ▫ EVENT Setup - Click the check boxes below to choose the events you need. - To delete, click the check box again. [Fig.7-111 Event setup] ▫ INTERVAL TIME Setup - Click the INTERVAL TIME (see Fig.7-112) to set the interval time of sending emails and then choose...

7. Setup 127 Note : If the motion is selected in Fig.7-112, you may receive numerous emails from the DVR systems due to a couple of factors such as continuous moving objects, a strong and changing lighting source, low resolution and noises of cameras. In case of this, select a longer INTERVAL TIME a...

Stand-alone DVR Instruction Manual 128 7-8.1. VIDEO ENHANCEMENT ON EACH CAMERA ▫ Click on an INPUT button in the VIDEO ENHANCE menu. ▫ The CONTRAST and BRIGHTNESS sliders will be displayed along with camera picture as shown in Fig.7-114. ▫ Adjust Contrast and Brightness with the sliders by clicking ...

7. Setup 129 7 -8.2. VIDEO ENHANCEMENT ON VGA OUTPUT ▫ Click on the VGA OUTPUT in the VIDEO ENHANCE menu. ▫ The CONTRAST, BRIGHTNESS and SATURATION sliders will be displayed along with camera picture. ▫ Adjust Contrast, Brightness and saturation with the sliders by clicking the mouse. ▫ To return to...

Stand-alone DVR Instruction Manual 134 8-2. Installing the Program to PC Install the program into PC by using program CD (supplied) as follows. How to install the program 1. Start the operating system (Windows 2000/XP/VISTA). 2. Insert the program CD into CD-ROM drive. 3. Open My Computer , and then...

8. Remote Host Program 135 8-3. Internet Explorer When you are trying to use this function, it is highly recommended that the password should be turned ON in the SYSTEM menu not to enable unauthorized personnel to access your DVR system (See section 7-2.3). Up to 10 users can remotely access your DV...

Stand-alone DVR Instruction Manual 136 • Click on the following message. This site wants to install the following add-on: ‘DVR Master’ from ‘Clover Electronics USA’. If you trust the website and the add-on and want to install it, click here…. • Click on the click install ActiveX Control …. on the po...

Stand-alone DVR Instruction Manual 138 Table. Description of Remote Host Program Button ① Minimization Button ② Close Button ③ Current Time ④ Connection Button ⑤ Setup Button ⑥ Player Execution Button ⑦ Capture Button ⑧ Multi-Mode ⑨ Terminal Mode ⑩ E-map Button ⑪ Splits the screen in 4, 9 & 16ch...

8. Remote Host Program 139 8-4.1. Setup ① Version number It represents the current version number of the Firmware. ② Copy Refer to Section 8-4.10 in regards to copying methods after selecting one between the Quick Copy and the Live + Copy. ▫ Quick Copy Click on the Quick Copy for faster copying the ...

Stand-alone DVR Instruction Manual 144 8-4.5. Replay It is possible to replay the recorded data from the DVR system by using the Replay button in Fig.8-10 in the Multi mode only (refer to section 8-4.9.2). - Click the Replay button as shown in Fig.8-10 to playback the recorded data from the DVR syst...

Stand-alone DVR Instruction Manual 146 8-4.6. COPY It is possible to copy the recorded data from the DVR system to a client PC by using the Copy button in Fig.8-13 in the Multi mode only (refer to section 8-4.9.2). - Click the Copy button as shown in Fig.8-13 to copy the recorded data from the DVR s...

8. Remote Host Program 147 “ALL” in yellow represents that all the cameras are selected. The camera channel number(s) in yellow represents that the corresponding channel(s) are selected. - Click the Copy ( ) button and then the copying progressive bar as shown Fig.8-15 will show up. - While copying,...

Stand-alone DVR Instruction Manual 148 8-4.7. Switch the Normal Screen to Full Screen ▫ Click the “FULL SCREEN” button on the DvrMaster as shown Fig.8-16 and then the current screen size will be enlarged to fit the monitor’s screen size, but the resolution will be lowered. ▫ Click the “FULL SCREEN” ...

8. Remote Host Program 149 8-4.8. Speaker / Microphone Buttons of Remote Host Program ① Audio Input channel selection: Select the same audio channel as the DVR has. ② PC Speaker ON/OFF: Turn the Speaker ON or OFF by clicking the mouse. ③ PC Microphone ON/OFF: Turn the Microphone ON or OFF by clickin...

Stand-alone DVR Instruction Manual 150 8-4.9. Connection mode There are two kinds of connection mode (See Fig.8-19) on the DvrMaster. Select one of them by clicking the mouse depending on your application. 8-4.9.1. Terminal mode The functions of icons such as Recording, Play, Copy, Setup, System Sta...

Stand-alone DVR Instruction Manual 152 8-4.10. Copy in the Terminal mode There are four icons such as NETWORK, USB, CD and DVD in the COPY menu of the Multi mode. The recorded data will be saved in the Backup Files (Open Windows Explorer – click My Computer - click the Program Files – click DvrMaste...

8. Remote Host Program 155 - To rename, right-click a saved eMap list and click “Rename” on the pop-up window as shown in Fig.8-27 . - To delete, right-click a saved eMap list and click “Delete eMap” on the pop-up window as shown in Fig.8-28 . - To display, double-click one of saved eMap lists. The ...

8. Remote Host Program 157 8-4.12 Pan / Tilt & Preset You can control the PTZ camera through DvrMaster. This feature is basically identical to what the DVR system has. Refer to section 6-7.7 PAN/TILT on page 46 . [Fig.8-32 PAN / TILT] PRESET / RUN FOCUS ZOOM PAN / TILT CHANNEL SELECT

Stand-alone DVR Instruction Manual 158 8-5. PLAYER [Fig.8-32 Player] Chart. Button of Player Program ① Status window (Play mode, Date, Time) ② Calendar ③ Convert to AVI File ④ Search button for replaying ⑤ Capture button ⑥ Print button ⑦ Division button ⑧ Playback (Replay) speed Control ⑨ Search sli...

8. Remote Host Program 159 ① Status window (Play mode, Date, Time) It indicates the play mode, date and time. ② Calendar It shows the date currently being replayed. [Fig.8-34 Calendar] ③ Convert AVI File Convert the recorded files to AVI files. - Click the Convert AVI button on the Player and the Co...

8. Remote Host Program 161 [Fig.8-38 Select one of the Channels] [Fig.8-39 Start Convert Button] How to play the AVI files By using Windows media player: - Click the OPEN button on the Convert AVI window and double click one of the AVI files to play. The AVI files will save in the AVI Files folder (...

Stand-alone DVR Instruction Manual 162 ④ Search button for Replaying - Click the Search button on the Player and the Browse for Folder will be displayed. - Select the folder that contains the recorded data and click the OK button on the Browser for Folder. One channel or all the channels can be repl...

8. Remote Host Program 163 ⑦ Division button Select one of the following divisions while replaying. ⑧ Playback (Replay) Speed Control Move the slider with the mouse to control the replaying speed. The “0” represents the normal speed, “-“and “+” represents slow speed and fast speed respectively. [Fig...

165 9. Installation of additional HDDs CONTENTS 9-1. HDD (H ARD D ISK D RIVE ) INSTALLATION ......................................................................... 166 9-2. I NSTALLATION OF AN ADDITIONAL HDD ................................................................................ 167 9

Stand-alone DVR Instruction Manual 166 9-1. HDD (Hard Disk Drive) INSTALLATION ▶ Three of internal Hard Disk Drives (HDD) and a CD R/W or DVD R/W can be installed in the system. DVR manufacturer already installed a 500GB of Hard Disk Drive (IDE) and a DVD R/W. To install additional hard disk drives,...

9. Installation of additional HDDs 167 9-2. Installation of an additional HDD ▶ Set the jumper setting to “Cable Select” position on the additional HDD. Note : Be sure that the jumper setting is correct. If not, the system will not recognize the additional HDD. ▶ Turn off the power. Unscrew and remo...

169 APPENDIX CONTENTS R ECORDING TIME TABLE ............................................................................................................170 F ACTORY DEFAULT SETTINGS .....................................................................................................171

Stand-alone DVR Instruction Manual 170 Recording time table HDD: 500GB, Based on 16 cameras Recording Resolution : CIF(320 X 240) DAYS 30 fps 15 fps 10 fps 7.5 fps 5 fps 3 fps 2 fps 1 fps (480fps) (240fps) (160fps) (120fps) (80fps) (48fps) (32fps) (16fps) Each CH (16CH/fps) BEST 12.14 24.28 36.42 48...

171 Factory default settings (1) LIVE SCREEN 16 SPLIT OSD ON (2) TIME / DATE DISPLAY: ON TIME FORMAT: 24 HOUR DATE FORMAT: MM/DD/YYYY (3) LOAD / BACKUP CONFIG NONE LISTS (4) USER ACCOUNT PASSWORD: SET YOUR PASSWORD (THE PASSWORD IS NULL) PASSWORD ON/OFF: OFF (5) IR REMOTE ID OFF (6) HDD OVERWRITE ON...

175 FAQ CONTENTS I CAN NOT LOGIN .......................................................................................................................176

Stand-alone DVR Instruction Manual 176 I can not login ▶ Please check if the link LED of DVR and LAN port of PC are lit. ▶ Please check if the IP address on DVR and the PC is identical. Check SYSTEM STATUS by pressing STATUS button of DVR MY IP: xxx.xxx.xxx.xxx Check Target IP Address by clicking CO...

177 Limited 2Year Warranty This warranty gives the original purchaser specific legal rights and you may also have other rights, which may vary from state to state. If our products do not function because of any defect in material or workmanship, we will repair it for free for 2 year on parts and lab...

Stand-alone DVR Instruction Manual 178 How to obtain Factory Service • Original purchaser must fill out the warranty card and mail it to the factory with the model number, serial number and the date of purchase. • We will repair or replace, and return the system to the owner under this limited warra...